अच्छा वीडियो था । एक बात clear नहीं हुई कि torqe reference के बारे में ज्यादा बात नहीं हुई कि torque reference control कार्ड को torque reference किस प्रकार और कहाँ से मिलता है । और PLC bits के बारे में भी प्रकाश डालिये ।धन्यवाद ।
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Much thanks! i got enough working principle of vfd . i get gap on how to use it esp for multi function 2,3,4 motors . Add me pls, if you have some thing on its usage .
There may be short circuit in IGBT inside drive.disconnect motor from drive and run the drive without motor if output voltage is balanced and drive keep running then drive is not faulty.
what is the requirement of external torque reference in torque reference control block diagram as well as what is the its effect on speed pid regulator?please reply sir..
check the load, decouple the motor with load and check shaft, it should be free, and run without load and check current, check motor current setting and overload factor setting parameter, if everything ok increase acceleration time slitely..this may help also check motor bearing condition and ..
Sir ji jab HM drive ki output voltage meter se measure karte hai to meter par voltage show Nahi karta jabki motor run Karti hai or input voltage Sahi measure Hoti hai aise kyu . please sir iske baare me bataye
Drive ka output Pulse width madulated hota hai but our meter will measure average voltage .if you use digital multimeter meter it can be checked. aur input me soinosoidal voltage hota hai wo bhi multimeter measure kar sakta hai
Sir mere Yaha PLC lagi hui h or V.F.D lagi hui h joki 2 motor chalati h forward bhi or revised bhi chalti h mgar mere ko direct signal motor ko dekar Chala h too kya karu sir please help me
Sir Matlab ki PLC me dusra koi fault Aaya h magar mere ko jaldi se motor chalani h taki me motor ko piche kar dugaa too aaram se fault theek kar Sakta hu taki saara Kam hota rahe
Apko drive ko ek digital input deke drive ka on off and speed reference terminal k through karna padega aur potentiometer laga k speed reference dena padega.mai ek video banane wala hu bahut jaldi..
Dear sir Mere pas 1 danfoss drive ha jisma mod no fc -51 k1p5 ha usko auto manual dono type se use karte h Usmai ek 0 to 20ma ka trans meter bhi laga ha ,no 12 no se 60 par transmitter ko reference Diya gaya ha aur 12 no se hi 27 no ko digital input Diya ha .Jase ise selector switch se on karte ha 13 no fault ata ha auto mad ho ya manual mad. Please tell me something about this please....... My what app no 8383878650
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .....
Your explanation is so simple that a fresher can also understand. Thanks for knowledge sharing!
You are welcome!
sir,i like your final advice anyways ..." be happy and smile" good to remember it
Sir,your teaching method and process is very simple to understand.keep it on.👍👍
I like your video very much. Your way of teaching is so nice.kindly make the video about encoder details and servomotor details.awaiting your update.
Knowledgeble video ....👌👌👌
th-cam.com/video/kfjJr7GAxr8/w-d-xo.html
Thank you sir
Very good interpretation
Thanks for TheVideo!🙏
Thanks sir for clearing fundamental of drives, sir if you also justify the use of choke with the help of learning video then it will help us more ...
th-cam.com/video/kfjJr7GAxr8/w-d-xo.html
Great work sir ji
Sir very nice video
1 question sir motor run on AC supply then why we first convert AC supply into DC and then again DC to AC
Nice video sir..
अच्छा वीडियो था । एक बात clear नहीं हुई कि torqe reference के बारे में ज्यादा बात नहीं हुई कि torque reference control कार्ड को torque reference किस प्रकार और कहाँ से मिलता है । और PLC bits के बारे में भी प्रकाश डालिये ।धन्यवाद ।
Torque reference par mai alag se video banaunga.thanks for this feedback..
उस video का मिल सके तो उपलब्ध करवाएं, और plc bits के बारे में भी । धन्यवाद ।
Wonderful sir
Please make videos on sectional drive and standalone drive..
sir DC drive ka bhi video banaw n sir g please❤❤❤❤❤❤
Very clear understanding
Vfd ka manual ko kaise understand kr ke koi v motor ko control kar sake aise video bano
Sir: Put Video to make us install the ABB's Variable Frequency Drive
Thank you sir.
Sir, Do you know anything about Starter software used for Siemens drives. If possible please make videos on it..
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Good
Sir help one video make ac motors high voltage igbt how to work for motor with painel internal connection pleas
Miss you your video sir
Thank You ❤️
Can a single phase to three phase VFD, be used to get solar power and to run the 1 hp Crompton Greves submerssible pump with 2 kw solar panel
Sir ladder logic FBD STL LOGIC KASE BANATE HAI ISKA BHI VIDEO START KARIYE POINT TO POINT SAMJH AANA CHAHIYE
Very good
thanks a lot, keep in touch
Very good explanation .sir
IGBT firing angle pe video banaiye plz
Maine firing sequence pe banaya plz Pehle usko dekho. Firing angle pe mai aur video banaunga. Thanks for your kind suggestions.
Sir how speed reference is converted into torque reference as only one mode is active at one time.
Thanx sir
Nice voice again
भाई एक question tha
Ager vfd ke output me MCB ya relay lagaye to kya wo work karegi
Yes Relay/MPCB are recommended in output of drive.MCB is not suitable for motor protection so don't use.
Much thanks! i got enough working principle of vfd . i get gap on how to use it esp for multi function 2,3,4 motors . Add me pls, if you have some thing on its usage .
Sir what is reason for vfd trip on over current when motor load cable and everything is normal condition.what happened in internal fault in vfd.
There may be short circuit in IGBT inside drive.disconnect motor from drive and run the drive without motor if output voltage is balanced and drive keep running then drive is not faulty.
@@aforautomation thanks sir very much
How about under voltage supply.....
Thanks
Thank you
Sir single phase input to single phase out put Kon si vfd vfd lagegi
Sir closed loop spped and torque seperately active mode karna padata hai ki at a time 2 active hote hai
at a time one active rahta hai
Thanks sir ji
welcome brother
Sir VFD PCB k baare me bhi btao khuchh please sir VFD gate voltage testing
Ritik Deol
+91-7777006122
indianationalautomation@gmail.com
National Automation India (LLP)
Regd. Office: 49, Rajeev vihar Hapur Uttar Pardesh 245101
Work Office: 41,Gali no. 2, 5 number Bhatta road, Meerut road, Ghaziabad Uttar Pardesh -201001
GSTIN:- 09AAQFN5704N1ZL
We deal in Industrial Automation (PLC,HMI, Ac/Dc Drive), Instruments (Sensor, PID,all types
valves,transmitter,transducer,flowmeter,flow switch), Panel manufacturer (Starter panel, PLC & Drive
panel, HT/LT panel), Repairing (Ac/Dc Drive, HMI & Panel) & Service provider…
Please contact free feel any inquiry .
spacel VFD Reparing
@@ritikdeol7727 sir muje vfd repairing sikhna h
Thank you sir...
Sectional Drive panel control circuit hai..
what is the requirement of external torque reference in torque reference control block diagram as well as what is the its effect on speed pid regulator?please reply sir..
th-cam.com/video/CcYkQy7TMOM/w-d-xo.html
អរគុណThank🙏🇰🇭
What is 230 volt three phase please explain
Cold loop torque control kab use karte hai
Sir ABB ke parameters kaise karte hai...eska video banao
okay. thanks for watching
Cold lop Speed ham kab use karte hai
Sir G120 SIEMENS KA VFD KA DI DO AUR PAPRAMETER BATAO
Simense ka 100 hp ka drive hai usko over current fault aa rhaa hai to usko kya kiya jaye plz bataye sir
fault kab aata hai?
starting k tume pe ? ya continuous running time pe?
check the load, decouple the motor with load and check shaft, it should be free, and run without load and check current,
check motor current setting and overload factor setting parameter,
if everything ok increase acceleration time slitely..this may help
also check motor bearing condition and ..
Sir ji jab HM drive ki output voltage meter se measure karte hai to meter par voltage show Nahi karta jabki motor run Karti hai or input voltage Sahi measure Hoti hai aise kyu . please sir iske baare me bataye
Drive ka output Pulse width madulated hota hai but our meter will measure average voltage .if you use digital multimeter meter it can be checked.
aur input me soinosoidal voltage hota hai wo bhi multimeter measure kar sakta hai
Hi
Sir regenrative drive ka block diagram bataiye
i will make very soon, keep in touch.. thanks for watching..
Our regenerative drive always trips on DC link voltage during power outage..
Sir kya hua ap ab video kyo nhi bnate hai
actually i changed location, laptop lene k baad phir start karunga
sr, aapke aur videos kyon nahi as rahe hain
th-cam.com/video/kfjJr7GAxr8/w-d-xo.html
VFD DC rectifier kyo use krta h
Sir mere Yaha PLC lagi hui h or V.F.D lagi hui h joki 2 motor chalati h forward bhi or revised bhi chalti h mgar mere ko direct signal motor ko dekar Chala h too kya karu sir please help me
Agar PLC Kam naa kare to ham kya kare motor chalane ke liye
Sir Matlab ki PLC me dusra koi fault Aaya h magar mere ko jaldi se motor chalani h taki me motor ko piche kar dugaa too aaram se fault theek kar Sakta hu taki saara Kam hota rahe
Apko drive ko ek digital input deke drive ka on off and speed reference terminal k through karna padega aur potentiometer laga k speed reference dena padega.mai ek video banane wala hu bahut jaldi..
sir,apka koicontact no. milega kya?jisse humdirect v bat kar sake agar kuch problem ho vfd k bare me to
Ritik Deol
+91-7777006122
indianationalautomation@gmail.com
National Automation India (LLP)
Regd. Office: 49, Rajeev vihar Hapur Uttar Pardesh 245101
Work Office: 41,Gali no. 2, 5 number Bhatta road, Meerut road, Ghaziabad Uttar Pardesh -201001
GSTIN:- 09AAQFN5704N1ZL
We deal in Industrial Automation (PLC,HMI, Ac/Dc Drive), Instruments (Sensor, PID,all types
valves,transmitter,transducer,flowmeter,flow switch), Panel manufacturer (Starter panel, PLC & Drive
panel, HT/LT panel), Repairing (Ac/Dc Drive, HMI & Panel) & Service provider…
Please contact free feel any inquiry .
spacel VFD Reparing
Dear sir
Mere pas 1 danfoss drive ha jisma mod no fc -51 k1p5 ha usko auto manual dono type se use karte h
Usmai ek 0 to 20ma ka trans meter bhi laga ha ,no 12 no se 60 par transmitter ko reference Diya gaya ha aur 12 no se hi 27 no ko digital input Diya ha .Jase ise selector switch se on karte ha 13 no fault ata ha auto mad ho ya manual mad.
Please tell me something about this please.......
My what app no 8383878650
Thank you sir
th-cam.com/video/rEbg-kYxXUA/w-d-xo.html
Sir bs iss video hindi ya english me samjha dijiye bahut help milega muje🙏
kya thik h ?
Sir apse WhatsApp pe bath Kar Sakthe he
Amartami cant understand.speak english
Very good
Sir: Put Video to make us install the ABB's Variable Frequency Drive
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
By changing the width of wave it's time duration gets changed ,and frequency is equal to 1 by T ,so we can change frequency also.
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .......
Sir by changing width of Wave, we can change output voltage,, this is clear.. But if we want to change output frequency , so how to do this in inverter ???? Please reply .....
Maine ek pwm pe video banai hai wo dekhiye apko clear ho jayega