I have an '06 5.7 H and this procedure seemed to have destroyed my Throttle Body (TB). I did disconnect the Neg. on Battery, but did not remove the TB for the cleaning as in the video. I also used my finger and toothbrush as in the video. Upon completion, as the fellow covered, the vehicle did run rough but that did clear up. However, when I next drove the truck and ever since, I am getting the Red Flashing lightning bolt error. Since, in doing research, everything says to remove the TB and most say not to touch the fin. I would recommend removing the TB, it's only 4 bolts and obviously wish I had done that. One video I saw, the fellow removed the TB an showed where it states "DO NOT CLEAN" right on the unit. He cleaned it and it seemed to work well. Anyway, I've ordered a new TB.
This method stands the risk of trashing your stock TB. I owned my 08 for 3 days in 2013 when it needed a new TB post cleaning. This is how I always cleaned them previously but now they come off the vehicle, cleaner sprayed on the rag and then the rag to the throttle body. Do not spray directly into your throttle body. You've been warned. Great video for dismantling though.
I wasn't really worried about the throttle body but the fuel injectors. That debris can clog one or more of them unless there is some sort of filter before the injector. I don't see how spray it directly makes a difference than wiping it with a rag do you care to explain more? I am going to be cleaning my TB again. The first time I just sprayed it like in this video but my plan is to remove it and clean it correctly.
Thank u so much I can tell a huge difference between when my rpm drops from 600 it's now studying at 700 thanks dude and my gas mileage is a lot better 😀
+Sparkchaser91 Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
Back 2005 guy had old 1961 Caddy. Idle was so rough and low. With Gumout and a toothbrush I cleaned the throttle plate, poured some more in carb, let her sit about 10 minutes. That baby fired up and ran like a new engine. idle up, smooth. Guy thought I was a magician.
You can just unclip airbox, unscrew the 2 bolts and take out the whole thing in one unit. Leave the filter in the bottom of air box to hold your tools. While your in there clean or replace the pcv valve and when done replace the air filter.
I think you’re not supposed to move or touch the blade on any electronic throttle body because it will mis calibrate so Please don’t do it how it’s shown in this video otherwise you will have to reprogram it with a computer program compatible with dodge ram ecu or in the worst of the cases replace the throttle body with a new OEM one!!! Please do your research first and you’ll se what I’m talking about ✌️
Yes you're right but that's why I'm here in this video because on the Dodge Ram Hemi 5.7 the throttle won't open when the key is ignition on and foot on the gas pedal like the Chevys so I don't know what the f*** to do now I'm just clean the outside of the throttle for now but why doesn't the throttle open when the ignition key is on
These guys usually make good videos but this one is not recommended, always best to remove throttle body for cleaning, all that grime is being pushed down into ports.
yes it sure can. Remove the wiring harness before even touching these things, and never stick your fingers in there with it hooked up! High torque motor with a gear reducer will take your finger off like nothing! Honestly, it's 4 more little 8mm bolts, and it slips right off. I've never seen anyone leave it on to clean. Why would you wanna flush all that crap down your intake? And it's way easier to clean on your bench, or parts washer if you have it.
correct me if I am wrong, by taking off the negative terminal, that allows you to move the throttle body to clean it, so you don't cause issues with your throttle coding. Also correct me if I am wrong, you can also have someone turn the ignition on and hold down the throttle while you clean it.
+Andy Southern You want to make sure the negative is disconnected so you do not cause any issues with the computer or electrical system while cleaning the part. you do NOT want the vehicle on while doing this process.
I was told by a dodge mechanic, that the only 2 ways to clean there throttle bodys is 1. use a scan tool to open throttle to wide open, or 2. have some one turn the ignition on but don't start engine then have then slowly push the throttle all the way wide open, then get in there with throttle body clearner and a tooth brush and get at it lol once done cleaning have the person who is holing the throttle wide open to slowly release the throttle. then turn off ignition. this is what he told me ......Yup. Don't touch it with the key off, or the battery disconnected, unless you want to buy a new one. You have to go Wide open throttle with a scan tool, or it MAY do it with the key on, foot down on the gas. The TPS and the Throttle actuator are both on the same shaft, so it may lose position if the key is off or battery disconnected. Take the intake elbow off, key on(not running), see if it opens wide. If it does, have somebody hold the pedal, get a tooth brush and a can of intake cleaner, get er done!!
No, definiitely don't clean it while the truck is running. It's very easy to remove, and that's how you should clean it. 4 bolts, 8mm. Keep your fingers and engine safe.
zachary i need your help i have 2007 dodge ram 1500 5.7hemi and i want to clean throttel body so i dont have a scan tool so i can turn key and push on gas to ooen it and then clean? So dont disconnect battery? I am confused please hellllp
My mother in law has a 2007 Dodge ram 1500 4x4 with 5.7 liter , this scary situation caused so much anxiety for my mother in law that she Don’t want to drive it anymore, So she was going down the highway at 65 miles and there was a car go slow so she is passing the car and seen a car coming so she kicks the pedal down and makes it , but the truck is still in high exceleration and going higher , she panicked and try’s to hit the brake but can’t stop , finally she able to put the vehicle in neutral and coast to the side of the road and the engine is just blasting in high rpm , what would be the cause of this .
+Enimativ D We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
The throttle body could attribute to that. Alot of problems like that happen in the airflow parts of the engine. Those are the easiest to work on too. So it doesn't hurt to see
Anyone remember the GUMOUT Cleaning Kit for carbs? Plug fuel line, feed straight GUMOUT into carb. from bottle you hung under the hood engine running. Boy those kits helped. They were discontinued because of fire hazard. I got lucky and Penzoil sent me like 8-10 kits for free.
We currently do not have an auto repair video specific to your vehicle. You might be able to apply some of the basic steps shown in this video to your application. +Keesha Tyler
Thanks for checking us out! We would not be able to guarantee the procedure that would need to take place if the light appears on your dash. You can always try cleaning the thorttle body first to see if it fixes the issue. Otherwise, the item may need to be replaced. We hope this helps you out! +Chase Kennedy
what about the 3.7L V6 ? I am unable to figure out to remove the resonator box/air intake cover? i have an 08 , but your hemi engine removal is a breeze compare to mine. those bolts under the alterntor and oil filler I dont have them. Reading online and everyone has the 4.7 , Hemi or the 4th gen ram. Any clue on removal?
I have the 3.7L engine. Sorry it took three years for you to get a reply :) The resonator is mounted with two bolts, one of the left and one on the right. The one on the passenger side is at an angle and the one on the drivers side is vertical. Once those bolts are out, hit the bottom front of the box upward, with your fist or a rubber mallet, to loosen the post from the hole it's in. Then grab the box with both hands and move it around to loosen the outlet from the throttle body. Pull it towards you, away from the throttle body.
Fred No... You disconnect the battery because you need to be able to move the blade manually without it trying to keep closed and without it being energized at all. Inside the throttle body the motor is very powerful and can cut your fingers if it tries to close. You disconnect the battery and when you're done reinstalling everything, the ECU will have a blank map and will relearn the TPS values which have changed after the cleaning.
@@mannys9130 it's about time someone has a brain on youtube. There is a lot of bad advice out there . If you dont no the answer dont make one up it will cost someone big buck to fix something that wasn't broken .
![“อ.เบียร์ คนตื่นธรรม” มาตามคำเรียกร้อง แหกศาสตร์ฮวงจุ้ย เตือนสติอย่างมงาย | แฉ 7 พ.ย. 67 [1/3]](http://i.ytimg.com/vi/5fc4S3xBNfc/mqdefault.jpg)
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
I have an '06 5.7 H and this procedure seemed to have destroyed my Throttle Body (TB). I did disconnect the Neg. on Battery, but did not remove the TB for the cleaning as in the video. I also used my finger and toothbrush as in the video. Upon completion, as the fellow covered, the vehicle did run rough but that did clear up. However, when I next drove the truck and ever since, I am getting the Red Flashing lightning bolt error. Since, in doing research, everything says to remove the TB and most say not to touch the fin. I would recommend removing the TB, it's only 4 bolts and obviously wish I had done that. One video I saw, the fellow removed the TB an showed where it states "DO NOT CLEAN" right on the unit. He cleaned it and it seemed to work well. Anyway, I've ordered a new TB.
I have a'04 Ram 1500 Hemi and I've cleaned mine a few times, and I always take off the TB, never had problems afterwards.
This method stands the risk of trashing your stock TB. I owned my 08 for 3 days in 2013 when it needed a new TB post cleaning. This is how I always cleaned them previously but now they come off the vehicle, cleaner sprayed on the rag and then the rag to the throttle body. Do not spray directly into your throttle body. You've been warned. Great video for dismantling though.
I wasn't really worried about the throttle body but the fuel injectors. That debris can clog one or more of them unless there is some sort of filter before the injector. I don't see how spray it directly makes a difference than wiping it with a rag do you care to explain more? I am going to be cleaning my TB again. The first time I just sprayed it like in this video but my plan is to remove it and clean it correctly.
Thank you, guys, for all of your videos!!! I have saved at least $3k in labor cost to get my 3rd gen RAM up and running again.
I love how they show how to do so much with the 2008 because thats what i drive
Same hahaah
You won’t be loving it for long….lol just kidding, that is cool,
What is the wire with the red connector called? Mice chewed threw mine and I can’t figure out what it’s called to order a new one
Thank u so much I can tell a huge difference between when my rpm drops from 600 it's now studying at 700 thanks dude and my gas mileage is a lot better 😀
Perfect video. It's not a hard job to do, but it was nice to watch this. It made an easy job even easier.
+Sparkchaser91 Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
Back 2005 guy had old 1961 Caddy. Idle was so rough and low. With Gumout and a toothbrush I cleaned the throttle plate, poured some more in carb, let her sit about 10 minutes. That baby fired up and ran like a new engine. idle up, smooth. Guy thought I was a magician.
Great video. Well spoken and easy to understand. Thank you very much!!!!!
+Drew k Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c
How do you do the throttle body reset procedure?
Do you have to relearn the throttle body after cleaning? I have an 06 Ram 1500
You can just unclip airbox, unscrew the 2 bolts and take out the whole thing in one unit. Leave the filter in the bottom of air box to hold your tools. While your in there clean or replace the pcv valve and when done replace the air filter.
I place my tools on the air cleaner all the time. Probably not the cleanest way but it damn sure is convenient.
Thanks excellent video and explanation blessings.🤗
I was just in there cleaning mine, leaving the bottom half of the air box gives you a good spot to set tools and stuff on and doesn't get in the way.
Is there a tps sensor for this exact tuck? I can’t find the location if so. Any help would be great
Would you recommend taking it off to clean it ?
+The New Life. Pt2 If you can, yes. You'll clean it better
I think you’re not supposed to move or touch the blade on any electronic throttle body because it will mis calibrate so Please don’t do it how it’s shown in this video otherwise you will have to reprogram it with a computer program compatible with dodge ram ecu or in the worst of the cases replace the throttle body with a new OEM one!!! Please do your research first and you’ll se what I’m talking about ✌️
you are right !
It's more of messing with the screws on the throttle blade because they are calibrated but it's best to have a trust worthy mechanic deal with it
Yes you're right but that's why I'm here in this video because on the Dodge Ram Hemi 5.7 the throttle won't open when the key is ignition on and foot on the gas pedal like the Chevys so I don't know what the f*** to do now I'm just clean the outside of the throttle for now but why doesn't the throttle open when the ignition key is on
I think if the truck is off and raw battery is disconnected you can move it. It's when the truck is running you should never do it.
This is incorrect
These guys usually make good videos but this one is not recommended, always best to remove throttle body for cleaning, all that grime is being pushed down into ports.
Do you know how to fix the accelerator pedal position sensor on the 03 04 ram hemi ?
Can moving the Throttle Body by hand like that mess up the calibration?
yes it sure can. Remove the wiring harness before even touching these things, and never stick your fingers in there with it hooked up! High torque motor with a gear reducer will take your finger off like nothing! Honestly, it's 4 more little 8mm bolts, and it slips right off. I've never seen anyone leave it on to clean. Why would you wanna flush all that crap down your intake? And it's way easier to clean on your bench, or parts washer if you have it.
it seemed to mess mine up.
Try and re calibrate it
Re learn
Yes it can mess up the sync settings and you will have to perform a relearn process
Really appreciate all the videos on the 3rd Gen Hemi! thanks!
I thought you weren't suppose to move the blade by hand
correct me if I am wrong, by taking off the negative terminal, that allows you to move the throttle body to clean it, so you don't cause issues with your throttle coding. Also correct me if I am wrong, you can also have someone turn the ignition on and hold down the throttle while you clean it.
+Andy Southern You want to make sure the negative is disconnected so you do not cause any issues with the computer or electrical system while cleaning the part. you do NOT want the vehicle on while doing this process.
I was told by a dodge mechanic, that the only 2 ways to clean there throttle bodys is 1. use a scan tool to open throttle to wide open, or 2. have some one turn the ignition on but don't start engine then have then slowly push the throttle all the way wide open, then get in there with throttle body clearner and a tooth brush and get at it lol once done cleaning have the person who is holing the throttle wide open to slowly release the throttle. then turn off ignition. this is what he told me ......Yup. Don't touch it with the key off, or the battery disconnected, unless you want to buy a new one. You have to go Wide open throttle with a scan tool, or it MAY do it with the key on, foot down on the gas. The TPS and the Throttle actuator are both on the same shaft, so it may lose position if the key is off or battery disconnected. Take the intake elbow off, key on(not running), see if it opens wide. If it does, have somebody hold the pedal, get a tooth brush and a can of intake cleaner, get er done!!
No, definiitely don't clean it while the truck is running. It's very easy to remove, and that's how you should clean it. 4 bolts, 8mm. Keep your fingers and engine safe.
zachary i need your help i have 2007 dodge ram 1500 5.7hemi and i want to clean throttel body so i dont have a scan tool so i can turn key and push on gas to ooen it and then clean? So dont disconnect battery? I am confused please hellllp
@@zacharysouthern9798 this is a joke right
What would the benefit be?
excellent job guys..
Will a bad throttle make it hesitate wild pressing the gas pedal
+monet Malisham This is possibly a symptom of a bad throttle body but could be many other things as well.
very well done video thank you!
Can no put a 4barrell carb on a 05 ram 1500 that has a throttle body
My mother in law has a 2007 Dodge ram 1500 4x4 with 5.7 liter , this scary situation caused so much anxiety for my mother in law that she Don’t want to drive it anymore, So she was going down the highway at 65 miles and there was a car go slow so she is passing the car and seen a car coming so she kicks the pedal down and makes it , but the truck is still in high exceleration and going higher , she panicked and try’s to hit the brake but can’t stop , finally she able to put the vehicle in neutral and coast to the side of the road and the engine is just blasting in high rpm , what would be the cause of this .
can apply this process to my dodge caravan 08 3.3 with electronic throttle body?
+Armando Sanchez You should be able to
My ram 5.7 08 doesnt get past 2de gear. Would this solve the problem?. I'm not from USA, we dont have any "dealer/specialst" for USA cars
+Enimativ D We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
I cannot accelerate smoothly. I depress pedal and nothing will happen and then suddenly rev up. Could this be the issue?
The throttle body could attribute to that. Alot of problems like that happen in the airflow parts of the engine. Those are the easiest to work on too. So it doesn't hurt to see
Anyone remember the GUMOUT Cleaning Kit for carbs? Plug fuel line, feed straight GUMOUT into carb. from bottle you hung under the hood engine running. Boy those kits helped. They were discontinued because of fire hazard. I got lucky and Penzoil sent me like 8-10 kits for free.
I can't find the Idle air flow sensor on my dodge ram 1500 5.7l hemi year 2007 , can you show a vedio on how to clean it or replace it ?? Thanks
+G Ali Mardani We're always cycling through common cars. We'll add this repair to our list! 1aau.to/m/Shop-1AAuto-c
Where the heck is the mass air flow sensor on these Dodge V8s? My friend has a 4.7 Durango and I can't seem to find it.
Good job, thanks!
Can this cause a bad misfire ?
Can you clean the 2005 Dodge Durango 4.7 V8 the same way
We currently do not have an auto repair video specific to your vehicle. You might be able to apply some of the basic steps shown in this video to your application. +Keesha Tyler
Can the throttle body be shot with a lubricant to help it move more easily .
What is the hose connected to the air filter box called
Is the Idle Control Valve on the throttle bodys? I know up to 02 they were on the back of the throttlebody but I'm not sure on my 03
+anon It is just below and forward of the throttle position sensor, attached to the throttle body. Thanks for the question.
@@1AAuto no thank YOU. Hopefully this is the last thing I have to mess with on this old truck to get it going again
+anon Thanks for checking us out! 1AAuto.com
My truck is not Reving past 2,500 rpm and it’s running rough how would I fix it
I have A 2002 Dodge 1500 and my RPM go up to 4-6 Why what can I do cheap and easy
Thank you kindly
Very helpful..Nice!
Nice. I'll do this.
great video... thanks!
should I replace or clean it the lighting bolt light comes on in the dash.
Thanks for checking us out! We would not be able to guarantee the procedure that would need to take place if the light appears on your dash. You can always try cleaning the thorttle body first to see if it fixes the issue. Otherwise, the item may need to be replaced. We hope this helps you out! +Chase Kennedy
How can I do the relearn on a 08 V6?
You’re not supposed to move the blade on the throttle body you’ll mess up the motor mechanism and will have to replace
+Ben Valentour Thanks for the tip!
what about the 3.7L V6 ? I am unable to figure out to remove the resonator box/air intake cover? i have an 08 , but your hemi engine removal is a breeze compare to mine. those bolts under the alterntor and oil filler I dont have them. Reading online and everyone has the 4.7 , Hemi or the 4th gen ram. Any clue on removal?
I have the 3.7L engine. Sorry it took three years for you to get a reply :) The resonator is mounted with two bolts, one of the left and one on the right. The one on the passenger side is at an angle and the one on the drivers side is vertical. Once those bolts are out, hit the bottom front of the box upward, with your fist or a rubber mallet, to loosen the post from the hole it's in. Then grab the box with both hands and move it around to loosen the outlet from the throttle body. Pull it towards you, away from the throttle body.
I have an 02 3.7 and it has a bolt on both sides and 1 hose on the back of it.
I would never clean my throttle body on my truck. It's super simple to remove it first.
I used penetrating oil in a spray can yesterday smh is that bad
What cleaner was used? Cause I've heard that some cleaner can harm the sensors inside
Max Morrison wd40
C. Smith No... Throttle body cleaner is specifically formulated for this job.
This video is good, but the title should be how not to clean your throttle body
Do these people ever respond to questions?
+Fred Hi Fred, We respond all the time. If you have any questions, you can leave a comment and we will reply back. 1aauto.com
Thanks!
Why do you disconnect the battery?
Because you can fry the computer or cause a spark creating a fire. I have never had these people respond to questions.
Fred No... You disconnect the battery because you need to be able to move the blade manually without it trying to keep closed and without it being energized at all. Inside the throttle body the motor is very powerful and can cut your fingers if it tries to close.
You disconnect the battery and when you're done reinstalling everything, the ECU will have a blank map and will relearn the TPS values which have changed after the cleaning.
@@mannys9130 it's about time someone has a brain on youtube. There is a lot of bad advice out there . If you dont no the answer dont make one up it will cost someone big buck to fix something that wasn't broken .
THE BUTTERFLY BLADE SHOULD NOT BE TOUCHED!!!!!! THEY ARE CALIBRATED TO SPECIFIC SPECS!!????????
+Jose Vasquez Thanks for the feedback!
You can touch it as long as the battery is disconnected. Never do it when the truck is running .
You can't do this to a Chrysler TB.
Lazy puts, why you didn't take the throtle out? All the dirt went into the engine..
I remove the throttle body
Wtf i payed 40 buck too clean mine