man this video may have just saved me a ton of money! iv changed wet sleeves but was clueless on a dry sleeve. I was looking for a new block for my kubota!! thanks man!
Did you have to bore and hone the sleeves? I really want to replace my liners when I rebuild the engine but I don’t have the time to pull the engine to have it bored
I have a d750 that needs a complete rebuild…I’m looking at complete overhaul kits with sleeves, do I order a kit for STD cylinder liners? Do I have to have the block bored for them? Appreciate any help, Thanks
@@tractorsmarinemechanic Yes, boring out the old Sleeves is a much Better/Safer way. BTW, this type of Sleeve can also slip inside the Block causing Noise and another failure. I've seen Aftermarket Sleeves that have STEP on their TOP, which LOCKS the Sleeve into the Block. The Block will have to be machined to accept this STEP. In some cases the new Sleeve is then Bored so the correct Piston Clearance is obtained!
man this video may have just saved me a ton of money! iv changed wet sleeves but was clueless on a dry sleeve. I was looking for a new block for my kubota!! thanks man!
Thank you for watching.if you try to remove the sleeve,just be careful to hit or scratch cylinder wall.
Very interssesting !
It's very difficult to find video showing that. Thanks !
are the cylinder liners prefinished, where do you get those?
please cover up those fuel outlets. there will get almost certainly metal parts inside this way
I thought you had to re-bore the block replace stock Kubota liners ?
You have to bore the block and fit the liners and rebore the liners for the pistons to fit. These must be finished liners fitted.
obviously it can be done, but what is the labor hours of this vs the cost of the tool?
Did you have to bore and hone the sleeves? I really want to replace my liners when I rebuild the engine but I don’t have the time to pull the engine to have it bored
No..
Do you have time to do the job a second time? You better because that is probably exactly what will happen.
Thanks you very much good working 🌹🌹🌹
Head fitting video pluses
Do you finish the cylinder liners to size before you install them? Great video!
Yap.thank you for watching
Never seen sleeves removed this way,but anything possible.
I have a d750 that needs a complete rebuild…I’m looking at complete overhaul kits with sleeves, do I order a kit for STD cylinder liners? Do I have to have the block bored for them? Appreciate any help, Thanks
Replace sleeve if needed
@@tractorsmarinemechanic Yes, boring out the old Sleeves is a much Better/Safer way. BTW, this type of Sleeve can also slip inside the Block causing Noise and another failure. I've seen Aftermarket Sleeves that have STEP on their TOP, which LOCKS the Sleeve into the Block. The Block will have to be machined to accept this STEP. In some cases the new Sleeve is then Bored so the correct Piston Clearance is obtained!
Sir Saan po naka Lagay na Kobuta tractor ung ganyan makina po 3 cylinder. Ty po
Sa b1200 po
Is th firing order of a L 3540 .....th same like 123
All Kubota engine with 3 cylinder is the same in firing order.thank you for watching.pls subscribe share and hits like.
Has v2203 and v1505 liners?
None
Сколько нароботки было до кап. ремонта?
Good video bro
Thank you.
sir ang k4c na makina pareho lng ba ang sukat nyan sa sleeve?
Iba po ata.
sir san ba makakabili ng mga pyesa ng k4c ung tractor ko d2350 mitsubishi?
Mahirap po hanapin Ang piesa ng mitsubishi.ano po Ang kailangan nyo n piesa?
marami po ba mabilhan ng pyesa sa tractor ko sir?
Medyo mahirap po.
where you buy parts ???
I think it's too far for you buy spare parts.you can buy from the Kubota, Philippines.
Bonjour ou prenez vous les pièces type cylindre ou chemise pour b7001
Super vodeo
Philippines
@@tractorsmarinemechanic merci ya t'il un site internet ou réseau ou commandé ses pièces ?
Sir pwede rin ba ganyanin sa kubota 4 cylender pagtangal ng sleeve v2203 kubota
Walang sleeve Yan 2203
Boss meron po bang sleeve ang d1403?
Wala po.D1402 meron
@@tractorsmarinemechanic salamat boss
Paki follow po ako sir sa fb.salamat din
@@tractorsmarinemechanic ok boss
Salamat
Boss meron bang kabitan ng temperature sensot tong 750?
Wala po.pero Kung gusto mo lagyan.barenahan mo sa head.at lagyan mo ng sensor.
@@tractorsmarinemechanic ah salamat boss
Hp?.
تمام
Ola me puede enviar un vídeo la postura de los piñones de la distribución Gracias
Япония ?
👍
Филипины
Почему то я думал что это японцы
ho-honingin mo pa pagkatapus lods ang sleeve.
Hindi n po sir.may nabibili n po nyn n pwd n isalpak.
@@tractorsmarinemechanic My kubota D902 din ako dito lods bt nag drive sya ng centrifugal pump (fire pump) galing offshore.
Bali pinalitan ng bagong engine, Quotation sa parts for repair ang gastos halos katumbas ng new engine.
Donde les ago una visita tengo un minicargador necesito ponerle un motor es un kubota 743 b
И весь образ в в поршневую ((
3аааа
Necesito un número telefónico
Donde les ago una visita tengo un minicargador necesito ponerle un motor es un kubota 743 bocat