DJI Mini 3 Pro Disassembly and Repair Guide: Ultimate Step-by-Step Tutorial
ฝัง
- เผยแพร่เมื่อ 31 พ.ค. 2024
- In this comprehensive repair tutorial, I'll walk you through the step-by-step process of disassembling DJI Mavic mini 3 Pro drone to replace ESC board, arm shaft, and vision sensors. Drone reassembly steps included!
Buy tools and parts on AMAZON:
Screwdrivers set: amzn.to/2Dp1Rcm
Opening tools: amzn.to/31ejoR3
Magnetic Mat: amzn.to/2Rw4G2w
Tweezers: amzn.to/39rWix5
ALIEXPRESS:
Screwdrivers set: ali.pub/302o00
Plastic Pry Tools: alli.pub/6dhrz1
Tweezers: alli.pub/6dhrts
DJI Mini 3 Pro Spare Parts: alli.pub/6fm1ke
Gimbal Calibration: • DJI Mavic Gimbal Calib...
More DIY repair guides on www.how-fixit.com
FOLLOW ME:
Instagram: / howfixit
Facebook: / howfixit
Twitter: / howfixit
Time code:
00:00 Replacement instructions
00:16 Screwdrivers and tools for repair
00:55 Start disassembling DJI mini 3 pro
01:21 Opening the drone body
02:10 Removing top cover of the drone body
03:30 Removing the GPS module
08:18 Removing the motherboard
09:11 Removing bottom cover of the drone body
11:15 Vision sensors replacement
16:22 ESC board replacement
16:51 Removing the arm shaft
17:17 Replacing rear arm
17:45 Replacing front arm
18:14 Drone arm replacement
18:42 Reassembling the DJI Mini 3 Pro drone
DESCRIPTION
Welcome to my channel, where I present the ultimate DJI Mini 3 Pro Disassembly and Repair Guide! In this comprehensive tutorial, I will walk you through the step-by-step process of disassembling and repairing your DJI Mini 3 Pro drone. Whether you're a beginner or an experienced enthusiast, this guide is tailored to meet your needs. You'll learn insider tips, tricks, and techniques to ensure a successful repair. Don't miss out on this opportunity to become a pro at repairing your DJI Mini 3 Pro drone. Watch the video now and take your repair skills to the next level!
Additional Information
After replacing the drone's GPS module, you will need to perform a GPS calibration of the aircraft in the DJI Fly mobile app.
After replacing the motherboard, you will need to calibrate the gimbal camera.
To replace the ESC board and drone arms, you will need a soldering iron and some electronics soldering experience. If you do not have soldering experience and the required tools, I'd recommend sending your drone to DJI for ESC board repair.
* DISCLAIMER *
This video intended for general information only. We will not accept any liability for damage or injury caused while following this guide. Any reliance you place on such information is therefore strictly at your own risk. This video description and commentaries contains affiliate links, which means that if you click on one of the product links, I could receive a small commission.
* AFFILIATE PROGRAMM *
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
#howfixit #fix #repair #djimini3pro - วิทยาศาสตร์และเทคโนโลยี
I wanted to see how the gimbal came out.
The ribben that was connected with a metal cap comes out with the gymbal, had to fix mine today and found it out watching this thinking the same thing 😂
Same
Dude, you rock! Very well thought out and made with the user/ viewer in mind. Very, very professionally done!
Yo when you starting putting the pieces on that square magnet mat thing, I knew I was in the right place😂
Grande vidéo faite par un vrai pro de la réparation et de la communication, un régal. Merci.
Quality video with actually decent chill music? and that magnetic mat looks pretty handy too. thanks.
I'm glad I watched this before doing it blind as i have bad habit of doing.
@13:27 I WANTED TO KNOW how that part (gimbal axis side cover) is to be removed and installed back as the shell popped out and I was scared to press and fix it as it could result in breaking of the tiny moulding.
Anyways now I know the gimbal case cover shell is an individual part, I can go ahead and fix it.
Thank you so much. 13:28
Can you take that off without having to disassemble the top?
I suffered a fall with my mini three Pro, breaking the flat of the GPS module. Replaced the module and the errors stopped appearing... However, the Drone does not crash, but it is no longer stuck in the air. I need help
Thanks for the video guide, I have to replace a broken rear arm. I can follow your guide and have good soldering skills so it should not be a problem but is there a quicker way to replace the rear arm without doing the entire tair down?
Thank you for the video! I changed the downward sensor and now the drone tells me there a vision sensor error (with calibration) and won't take off. How can you calibrate it?
I loved your vídeo. Is helping me a lot, since my drone felt on a corn field and I need to change several pieces. By the way, do you know of I need to replace the motherboard since I cant get the drone to sync with the remote?
Very good job, please continue with that good job.
Great Video. This will be very helpful when my DJI Care Refresh expires haha
can you tell if the connection of the camera is a proprietary part or is it some sort of standardized connection ? would be cool if it was possible to switch it for a different camera core
How do I order the sensor board for the Digi Mini 3 ?? Please help me brother please
Awesome great video! Can you tell me how to remove the battery shells. I ordered new ones due to my son running over both of the plastic housings on the batteries and put small dents just in the housing. The batteries are still working. I just can’t figure out how to get them apart.
You didn't mention anything about fixing stuck gimbal issue. I'm stuck with it. Opened up the drone. Saw wiring is intact. The gimbal is moving in 2 directions on booting up. 3rd direction is stuck. Please help
Hi thanks, but can you confirm the 2 screws on the underside above the gimbal need removing to get the top cover off?
Hi, I really need to know how to deal with the front sensor not working. HELP..!
Is there any particular order for prying off the body covers? They are so well clipped together and I need to remove and re-attach the top cover because parts of the left edge is not sitting flush with the main body after a crash. Drone is fine otherwise. Thanks
Very good
Are the sockets into which the screws holding the arm spring are screwed in, plastic or metal?
Bonjour
L’un des moteurs de mon mavic mini 3 tourne plus vite que les autres après un crash, ce qui empêche le décollage du drone. Quel est le problème?
Can you tell me what the screw size is for the front control arm shaft or where I can find them?
When you removed bottom cover you broke the black strip. What is it for? I had same accident :D
What about at the end of the arm the rotor Cen that cat be removed. I have grinding going on in there.
What is that black ribbon tape on the bottom cover.... When I went to remove the cover I ripped the tape
Nicely done. I might need to replace a drone arm next week and this gives me an idea of where I need to go. If I can get the tape off (tape? really? God damn) and go through the bottom, it looks like there isn't much preventing me getting to the ESC board to unsolder/resolder the wires for the arm.
At 6:25, concerning the black tape, in general is it okay if that black tape ripped off, an inch of it perhaps, due to the back and forth of the insert and release of the battery?
How can I fix the button? It presses down but doesn't do anything I noticed that mine vs yours doesn't have the white cap in the middle its the inside metal shorts instead.
Really great video!
I yanked the front right arm and did some damage. What kind of cost I'm I looking at? I wish I could post the picture to show you.
Do I have a real chance to repair a Mini 3 Pro that spent 24 hours in a mountain stream about 1 ft below the surface? Without disassembling the drone I can see minor signs of oxidization where the battery connects to the drone.
@13:20 GIMBAL AXIS SIDE COVER ASSEMBLY
Hi అన్నయ్యా 😍😍🥰🥰 చాలా Thanks అన్నా🥰🥰🙏🙏 ఇలా చేసి చూపించినట్టు ఇంకెవ్వరూ చేయలేదు... Super బాగుంది బాగా చేసారు
I changed my gimbal parts not it's not coming to centre. Please help with gimbal callibration.
This Dude is awesome. Great video 😅
The link for the drone spare parts does not work. Can you post an updated link please?
Can anyone help me or show me how to remove the metal motor cover on the DJI mini 3 please ?
Any ideas on a mini 3 with a 30210 error?
My dji mini 3 pro keeps giving me IMU error and callibration error
Great video thanks for sharing 👍. The music however, is quite annoying, you really don’t need it.
How long is the warranty on the dji mini pro ?
very informative video
Can somebody please help me?
I have changed one motor of the drone and put all together after that. When I want to start the drone I get the Erros that the ESC is not working Errorcode 6080027(and the battery could be broken or empty (I don ´t think so)).
I hope someone`s got a solution, thank you if you help me
Hi where is the location of the campus in the Mavic mini 3
Greetings from São Paulo BRAZIL.
I'm impressed by such great ability to handle these toys.
Congrats!! 👏
Here, 1+sbscrbd with thumbs up.
My mini 3 has got an issue.
Its camera lens is foggy with no reasons.
Amazing !
hello.
two questions:
1. can i remove the bareometer, so i can fly over 500m?
2. can i remove the speaker in the controller so i get rid of the annoying beeping sound?
You can mute the controller
Detailed pin to pin explanation
What's the black sticker on bottom cover ? I disassemble my bottom cover an ripped it of :( It has a metallic surface and now im fear that it was a part of the antenna system
Same here and I need answer but I can't found it. Please tell me your conclusion 6 months later
Thank you for posting this video! I literally just crashed my dji mini 3 pro a few mins ago and it cracked the top shell :( . Where can i order replacement parts?
Thanks!
Thanks for your support !
My back visioen sensor has an error. You didn’t removed it in your video 😢
Is this a Mavic or a mini pro 3???
one of my blade screws is stripped... any suggestions on how to remove it to replace the blade?
happened to me once, your best bet is to buy a micro screw extractor kit
I realize this is 6 months too late but for others, what I did when a prop screw got stripped is, assuming the propeller on that screw is damaged and will not be used again (as this process will damage it further) I took a flat file, and ran its thin edge across the head of the screw... Did that enough times it ended up digging a sort of trench in thr screw head, deep enough to use a flat head screwdriver to help unscrew it. Alternatively, you can use a small pair of long nose pliers to unscrew the screw but this too will damage the prop blade.
That looks like hot glue - you can either use a hot air rework tool to soften it or take a can of air and turn it upside down so it spits out liquid. That will freeze the hot glue and make it very brittle - you can then easily crack/shatter it.
Whats the torx screw size? Cant seem to figure out
5
Thank you!
I'm the 1000 liker 😅
The top shell cover has 2 more screws you forgot to show and I almost break the cover.
My drone gimbal stuck.. Can u help me bro?😢😢
u have to replace hole gimbal area. coast 300 €
Great video, but i waited all the time to see how to replace or fix the gymball and it not happened :)
Where’s the compass.
It would frustrate me a lot if the rotor blades were not removed during such a drastic operation!
Is the hot glue optional?
Also what is the minimum teardown required to replace the rear arms? Do I need to perform all prior steps in order to complete?
5 stars.....
i did'nt realise how zippy she is in sport mode. when i was landing her i had to reverse her slightly and the drone zipped straight in to a tree, tumbled and landed with a bang upside down on a concrete path. she's OK but a piece of plastic broke off the front left arm. i got a new arm to install but i'm horrified now to know that I have to perform brain surgery to attach the new arm?
same here, it's either do all this, or pay someone 1/4 of the price for something that might happen again.
@@susanbarragan6308 im going for it! ordered my new rear wing yesterday along with the items on the description. its $166 to have it replaced. Ill have another use for the tools and Ohio Drone Parts sells each OEM leg for $30-35. the chances of me breaking it again are too high to shell out so much money every time it happens.
The “Ultimate Guide” didn’t remove the gimbal. 🤦🏻♂️
mini 3 pro replacement motherboard $300?!
This guy is calling the mini the mavic...
look for him to do it @dr.drone.bahia