thankyou this video helped me fix a month old mini 3 pro I bought for really cheap because the camera wasn't working after the guy crashed it into his ceiling
@@FernandoSilva-lo5pl i did yes and all worked fine afterwars as thr cables pretty feeble then traded for a full dji fpv setup with a broken arm repaired that then traded again and now have a basically brand new mini 4 pro
I need to do this on my drone also I need to change the cable after doing this do I need to calibrate or use any special program on a computer or it's just good to go does any message will go saying gimbal erro or kind of
I have same problem, i crash with my drone, and not work the gimball just a very little move. What do you think its enough just buy a cable? Mechanism work well, i check all connector and i re connect but didnt work. I dont really want buy new gimbal or send to service both very expansive story... ( dji mini 3 )
If gimbal stuck and your all motor component is still old componen, maybe your cable is broken or maybe your gimbal pitch motor is dirty or broken. That can't fix with calibration software.
The point where the camera clips onto the motherboard gets very hot. As much as my finger can't stand it. I guess it's not normal. And the gimbal sometimes makes a grinding noise in some places. There are explanations for all this.?
@@Djiservisi hi i am an automotive transmission builder i have a question to ask you. when you pull the gimbal motor off and don't mark the screw location does that though off the calibration. thank for your time
Piece of junk chinese trash for $1000 for a cheap garbage drone and a minor crash my dji mini 4 is still giving me "gimbal stuck" after changing the rubber and this wire. 💩
Fixed my drone after a crash. Couldn't have done it without this video. Thank you for posting!
My first mini3 repair, thanks for sharing.
I am already your subscriber.
Greetings from Mexico.
thankyou this video helped me fix a month old mini 3 pro I bought for really cheap because the camera wasn't working after the guy crashed it into his ceiling
Did you have to replace the cable? Mine crashed too and it's like that.
@@FernandoSilva-lo5pl i did yes and all worked fine afterwars as thr cables pretty feeble then traded for a full dji fpv setup with a broken arm repaired that then traded again and now have a basically brand new mini 4 pro
Hello, good video. I already subscribed. Do the mini 3 and the mini 3 pro use the same cable? thank you
I need to do this on my drone also I need to change the cable after doing this do I need to calibrate or use any special program on a computer or it's just good to go does any message will go saying gimbal erro or kind of
hey from where did you purchase the new cable?
Does PTZ cable for mini 3 are the same with mini 3 pro?
Hello friend, can you tell me if I can repair a filament of this pra cable which is broken?
I have same problem, i crash with my drone, and not work the gimball just a very little move. What do you think its enough just buy a cable? Mechanism work well, i check all connector and i re connect but didnt work. I dont really want buy new gimbal or send to service both very expansive story... ( dji mini 3 )
In what failure do we need to replace ptz cable?
Crash maybe one or all motors are not working or camera signal not there you will get gimbal motor stuck sometimes
If your gimbal can't move, your error is gimbal stuck and your camera not shown.. but check your cable connector is plug to gimbal component or not..
Quando estou fazendo o vôo, o guibal começa ficar sem controle, o q seria esse problema
I have the same problem. I think this is one solution to change the PTZ cable. If it doesn’t work, then maybe we need to change the full gimbal module
great vid!
Great video!if you get a gimbal stuck error, will this fix the issue?and does it require dji software calibration once all settled?
It is not possible for me to give a definitive answer. Contact DJI Support.
If gimbal stuck and your all motor component is still old componen, maybe your cable is broken or maybe your gimbal pitch motor is dirty or broken. That can't fix with calibration software.
The background music sounds as if you were saving the world
The most frustrating part was the small round cap on the inner arm😡
Hot to buy cable gimbal?
I just changed the ptz cable, with watching your video...
The point where the camera clips onto the motherboard gets very hot. As much as my finger can't stand it.
I guess it's not normal.
And the gimbal sometimes makes a grinding noise in some places.
There are explanations for all this.?
after changing the cable will it cause error code 40021 or 40011?
Parabéns pelo trabalho
Meu drone está com problema nesse cabo. E vendo seu vídeo vou tentar fazer eu mesmo
Thanks
@@Djiservisi hi i am an automotive transmission builder i have a question to ask you. when you pull the gimbal motor off and don't mark the screw location does that though off the calibration. thank for your time
Seu video me ajudou muito. Fiz no meu drone e deu tudo certo. Obrigado
Tengo Dji mini 3 normal y en un accidente dejo de funcionar el gimbal pero funciona la cámara.
hello i have the same problem, did you solve the problem?
Same problem, replace the wiring.
any idea gimbal calibration error code is 1D020001. minor crash, no visible damage. the gimbal does not shoot at all.
hi price determination required
Did you fix this? same problem minor crash
Excelente ❤
❤️❤️❤️❤️
I already fixed my gimbal but pushed the Like just for the choice of music...
Please do a video for mini 4 pro camera lens error
my Dji mini 3 has ERROR 180016, 180017,180031. errors in the lower visual sensor
SHOWW 💪✋💯🤙👏👏👏👏👏
👍👍👍
❤️❤️❤️
Muito bom
Replaced the cable and gimbal still says its stuck with 40002 error
Contact the dji service in your city
Check your pitch motor. Maybe your pitch motor is dirty or maybe your motor is broken. or maybe the cable connector is not plug properly
Piece of junk chinese trash for $1000 for a cheap garbage drone and a minor crash my dji mini 4 is still giving me "gimbal stuck" after changing the rubber and this wire. 💩