Dyson Soft Cleaner Head - not spinning - kind of repair
ฝัง
- เผยแพร่เมื่อ 9 ก.พ. 2023
- This is a strange issue, I didn`t understand exactly why the motor mount changed its shape and got damaged. Excessive vibrations or using it on the carpet may have something to do with that. Still, the roller doesn't look like it is unbalanced and vibrations are not much higher than usual.
- วิทยาศาสตร์และเทคโนโลยี
![USAB Showcase: CANADA vs USA [OFFICIAL STREAM]](http://i.ytimg.com/vi/m9Cz3xsdDgc/mqdefault.jpg)
Nice job my friend!!! You saved me. Only thing is that the resistance is around 31 Ohms for my motor.
After the repair of the wires the resistance is now 8 Ohms....Thank you for the video!
Glad I could help
You legend. Solved my problem as well. Both wires were cut exactly like yours, and it was because the same exact part had its plastic "ring" that holds it in place broken where it fits in with the keyed plastic area. I just put some glue and some electrical tape around the edge to hold it into place. Hopefully it lasts.
Glad it helped!
Hey. Thanks for the fix. This is the reason mine stopped spinned and this video helped get it going again. My plastic mount was also broken with a section missing. Used superglue and will see how long it holds for.
Glad it helped
Thanks- solved my problem too- in my case the wire was not cut but the connector got loose -very helpful !
I'm glad I could be of help.
Same issue for me (2 wires cut). Thanks for this video. Problem fixed!
Thanks!!!!!
Glad it helped
Great video, helped me a ton!
Awesome, thank you!
This helped me out a lot! Thank you!
Glad it helped!
Merci beaucoup pour cette video, j'ai réussi a réparer mon balai dyson
Glad it helped!
This helped me a lot as well.. Thanks! :)
Glad it helped!
Exactly the same thing, it saved me! My version of the plastic part that's holding the motor was kinda broken, but some tough tape will do the job hopefully. Thanks!
Mine is having the same issue. The brush head stops spinning but when I disassemble and test it without the brush head on, the motor doesn't stop at all. I made sure all debris was gone and it's still not working. What could cause this?
Thanks to U man I solved the same problem ! Great
You're welcome!
How long is super glue and electrical tape going to hold it?
Mine doesn't spin in any case, with brush and without brush, the rotor doesn't rotate What can it be? I don't know how to solve
Sounds like a defect. The plastic holding the motor was broken. I haven’t disassembled all the way yet, but I am sure the wires are cut, too. I thought Dyson is supposed to be good.
Thanks you!
Glad it helped!
Hi when removing hair I cut through a black lining roller. The smaller purple / blue head won’t turn any quick fix please?
I'm sorry, I don't understand what you mean. Can you elaborate? Or can you send some pictures to TechFixPOVinfo@gmail.com?
If you catch something with brush bar and it stops it this will happen. The plastic piece in mine shattered so it's not fixable without new part.
Yes, in this case, only a new part will make your brush work again.
My V8 soft roller is also not spinning. I tried to remove the soft roller but it is stucked at the other end. Any idea how to remove it. Thanks
It looks like the plastic melted inside the roller. That can be caused by a stuck bearing (rusted?). You can remove it only by force, try to put some pressure on the roller with a flat screwdriver.
I have a problem, the brush doesn’t spin on Dyson. But if I connect 16v directly to the brush It spinning🤔 All connectors on Dyson are clean and when I check by multimeter it shows that there are voltage on the Dyson connectors. Do you have any ideas?
I think you have a problem with the electronic board of the vacuum cleaner. The board uses a MOSFET to power the brush and constantly monitors the consumption. It is possible that the MOSFET or another component is faulty.
Where can one get the new plastic part? Thank you.
Unfortunately, this component cannot be purchased separately.
Mine doesnt also spin. But i have deassembled the whole thing. The wires are intact. And sometimes it spins for like 1 turn and then it stops. I think its maybe an cracked cable or sum idk do you maybe know something i dont?
First, you should check if it works normally when the fluffy bar is not mounted. Maybe it is a mechanical issue. If it still doesn't work normally, you could check both wires individually using a multimeter set to read resistance.
This is my problem too the roller bar /motor has power then it does like a hiccup and stops, it does this every time
I have the same problem, all the wires are connected properly.
The other brushes works great, only this one, turn half spin and stop..
🤷♂️
Mine does the same, have you fixed yours yet?
I have the same issue. The brush spins for 1-2 seconds and stops. Pressing the power button again causes it spin again for a few seconds and stops. Sometimes it does not spin at all.
The wires are connected and seem to be okay as far as I can tell.
Could it be that the motor in the brush bar is the problem?
Having the same issue. .however, until the moment I saw the cable snap decided not to DIY.....leave it to service center to fix. Complicated.
Repairs like this are usually not done in service centers. Most likely they will recommend you to buy a new brush. This is also the purpose of this channel, to show how various problems can be solved to avoid the expensive complete replacement of the defective accessory.
thanks a lot same issue here haha
Glad it helped!
My dyson heads all spin backwards. It pushes dirt out in front rather than sweeps it into the vacuum. How to fix!!
what model is the vacuum cleaner?
@@techfixPOV V8
Watch this video I made: th-cam.com/video/BCf2DCHRWqU/w-d-xo.html
Depending on how the two wires (red and white) are connected, the brushes will rotate in one direction or another.
In your case, if all the brushes rotate in the opposite direction, I recommend that you reverse the two wires. If you watch the video from the beginning, you can see the entire disassembly and assembly process. Good luck!
If you have other questions, please ask.
@@techfixPOV omg u fixed it. ily
I'm glad it works now :)
La spazzola a volte non gira
Watch the two videos I made with this brush. Two different defects are presented.
Why should ever I pay so much money for this dyson-p*ece of sh*t, and then fix it by myself? What is more, the battery also sucks, it does not work after one year, if I use turbo-mode. I will never ever buy Dyson.
Screw all that. I'll just buy a new one.
That`s also an option :))