The arms you recommended are amazing but they are also ridiculously expensive. I have 49 inch monitor and 27 inch above it both mounted on the same 1 meter tall monitor post. Each has individual arm attached to the post. Post costed 35 Euro Arms costed 17 Euro each. I have this setup for over 2 years now and it did not fail a single time. I do extend forward arm with 49 inch monitor too whenever I setup my sim rig. When it is extended the post slightly leans forward under the load. Everything is set on a havy, very stable wooden desk. All I'm trying to say is...sure, if I had 400 dollars lying around I would buy one of the arms you advertised. But frankly, most people have more important things to spend money on.
Here's another tip. I have one of those IKEA desks that are filled with paper. They do not recommend using a monitor arm with this desk, but I' had two of them. I bought a couple of sets of wide reinforcement plates off of Amazon. These are metal plates that go under and over the desk to spread out the mounting pressure. I have a very heavy 49" Samsung CRG9 on my desk right now and the arm supporting it is working great.
Just FYI, you can often get 3D printed adapters for monitors that don't have VESA mounting holes. I had a 34" ultrawide HKC monitor, and the adapter for it was only like $10. Same with some of the MSI monitors that have a fancy stand but no VESA mounting holes. Purchase an adapter. They work great.
Hi! I have a 49" Samsung Odyssey CRG9 DQHD 120Hz monitor, can you recommend an arm for it? I have a standing desk that doesn't have a metal frame on the edges.
Hi my desk surface from the back to clamp the monitor arm is too long whereas it’s is open desk mine has a drawer so it makes the surface from the back very long will this not allow me to have a monitor arm because as i seen in the pictures they have a small clamp which wouldn’t fit my desk, is there any recommendations
Why do people mount monitor arms off to the side with ultrawide monitors? Shouldn't it be dead center directly underneath the screen to maximize longevity? Does mounting it to the side save space behind the desk?
I have a desk that is particle board with a thin wood veneer (Karlby from IKEA.) I did the grommet mount and it feels pretty solid. I'm sure I could have used the C-clamp and that would have worked just as well.
I have a question I want to buy a standing desk but my budget is entry level I want to get the kaemeng standing desk 140 x 70 is it any good bc pictures I can’t trust ? Haven’t seen it in a video of yours
Ok, I am looking for a solution for a 49" Curved Samsung monitor for a adjustable height powered standing desk., the Desk is 24" deep, I need an arm that will be able to handle the 44 LB monitor weight, but also let me push the monitor back way from the desk so it is not in my face. So something which I can mount to the desk, and the monitor can be pushed backwards, still being in the middle of the desk. I have tried a few things, but the pole is the limitation, as you cannot push the monitor more than where the pole is mounted to the desk. Any idea's?
Which we covered what we deemed to be the most common problems. It would be impossible to know what everyone’s potential problem is, especially if they don’t share it. Just complaining we didn’t satisfy your need doesn’t do any good for you, us or the rest of the community -Greg
Watch This: The Last Video You'll Need Before Buying a Monitor Arm - th-cam.com/video/oDAL_nmbZ6M/w-d-xo.html
The arms you recommended are amazing but they are also ridiculously expensive.
I have 49 inch monitor and 27 inch above it both mounted on the same 1 meter tall monitor post. Each has individual arm attached to the post.
Post costed 35 Euro
Arms costed 17 Euro each.
I have this setup for over 2 years now and it did not fail a single time.
I do extend forward arm with 49 inch monitor too whenever I setup my sim rig. When it is extended the post slightly leans forward under the load.
Everything is set on a havy, very stable wooden desk.
All I'm trying to say is...sure, if I had 400 dollars lying around I would buy one of the arms you advertised. But frankly, most people have more important things to spend money on.
They are sales man
What post/arm are those? Im looking for the type that could be above my regular monitor myself.
Wow, hats-off to this guy for investing into many nitty-gritty details. Nice !
Jxdhhdjxhxj
Wow, you pretty much covered all issues one could have buying these stuff, amazing video!
Here's another tip. I have one of those IKEA desks that are filled with paper. They do not recommend using a monitor arm with this desk, but I' had two of them. I bought a couple of sets of wide reinforcement plates off of Amazon. These are metal plates that go under and over the desk to spread out the mounting pressure. I have a very heavy 49" Samsung CRG9 on my desk right now and the arm supporting it is working great.
Oh man, thanks for this. We also have the IKEA white desk and noticed the thin material is starting to be dented.
Just FYI, you can often get 3D printed adapters for monitors that don't have VESA mounting holes. I had a 34" ultrawide HKC monitor, and the adapter for it was only like $10. Same with some of the MSI monitors that have a fancy stand but no VESA mounting holes. Purchase an adapter. They work great.
This guy mounts
Hi! I have a 49" Samsung Odyssey CRG9 DQHD 120Hz monitor, can you recommend an arm for it? I have a standing desk that doesn't have a metal frame on the edges.
Any recommendations for a 55 inch 16:9 37lbs „monitor“ with vesa 300x400? 😢
Hi my desk surface from the back to clamp the monitor arm is too long whereas it’s is open desk mine has a drawer so it makes the surface from the back very long will this not allow me to have a monitor arm because as i seen in the pictures they have a small clamp which wouldn’t fit my desk, is there any recommendations
What is the name of the type of c clamp mount at 1:14, for the desks with a long overhang
D Rick drilling like a boss!
I would love to see a test of various standing desks, comparing vertical stability when leaning into them, just like you did at 3:17
any budget options tested? the arms you show cost more than my monitor 😂😭
What about a pole mount for an 34" ultrawide curved monitor that is 20lbs? I don't have the room behind my desk for a swing arm.
excellent video
Why do people mount monitor arms off to the side with ultrawide monitors? Shouldn't it be dead center directly underneath the screen to maximize longevity? Does mounting it to the side save space behind the desk?
It might save space on the desk directly in front of you. Some of these monitor arms are incredibly over built.
If I have a desk thats made of particle board, would a monitor arm bracket help me use a monitor arm?
I have a desk that is particle board with a thin wood veneer (Karlby from IKEA.) I did the grommet mount and it feels pretty solid. I'm sure I could have used the C-clamp and that would have worked just as well.
@@gregorymoore2877 I have the same karlby set up, I ended up using a c clamp mount and a support bracket..no complaints so far!
I have a question I want to buy a standing desk but my budget is entry level I want to get the kaemeng standing desk 140 x 70 is it any good bc pictures I can’t trust ? Haven’t seen it in a video of yours
did you end up getting anything?
@@zephronic1062 not yet can’t afford it em but I found a desktop 160x80 it fits fine and found a frame so I just need £400 then it’ll begin
What could we do when the arm can`t hold the weight anymore? The problem with this arms is that they are disposable.
Ok, I am looking for a solution for a 49" Curved Samsung monitor for a adjustable height powered standing desk., the Desk is 24" deep, I need an arm that will be able to handle the 44 LB monitor weight, but also let me push the monitor back way from the desk so it is not in my face. So something which I can mount to the desk, and the monitor can be pushed backwards, still being in the middle of the desk. I have tried a few things, but the pole is the limitation, as you cannot push the monitor more than where the pole is mounted to the desk. Any idea's?
Most monitor arms have small screws that prevent the arm from going back ,so you just need to remove it.
I use an ergotron HX, very satisfied
Was looking for monitor arms and then I realized my 25lb 4k monitor is a bigggg boi
I have a 44lb Samsung g9😭😭
@@kriaz9916same
$450 for a mount?!? Hot dayummm
That monitor arm is more expensive than the monitor itself
No need to make a huge hole like in the video, just enough a hole the size of the screw.
there is not tips, you're showing the issues, but not actually showing the solution ...
If I had that monitor, my desk would hugely improve without doing anything else.
👍
reasons not to use amazon for something as complex as a monitor arm
4:25 abra-cadabra
or you could get a wall mounted arm like i did and the shaking isnt a problem whatsoever
Ergotron are way overpriced, as are many of the monitors you feature.
And thankfully, they are over engineered and over built as well. And they include a 10 year warranty.
or in other words, use common sense.
Saw the thumbnail hoping it could help with my problem but you didn’t even mention it once…
You didn’t either haha -Greg
But it's your video? I should watching this video for the solution. If I had the solution do you think I would be here?
Which we covered what we deemed to be the most common problems. It would be impossible to know what everyone’s potential problem is, especially if they don’t share it. Just complaining we didn’t satisfy your need doesn’t do any good for you, us or the rest of the community -Greg