I Just Say You Are A Good mechanic I wish you were here in California. But the mechanics out here are very bad they don't really take the time to look at the cars and trucks. I just want to say you're not going to cannock and I love you videos. I have learned a lot from watching your videos and asking questions. Thank you
I'm a subscriber of the female variety, and I love watching your videos. Honestly, I don't care when you talk about the "fellas", or when you say "there's your problem, lady!" I find that last bit super funny. That aside, I have learned so much from watching your videos, especially the ones where you run down electrical issues... I've gotten better at diagnosing issues by following your techniques. Thank you for all your great videos, even the ones you think are silly. Every one of them teaches something new!
Your experience is impressive. I think you only showed the wiring diagram for our benefit because I don’t think you needed it. You found that bad ground in no time. And the way you repaired it was the same way I would. Nice work.
honestly I think he shows the diagram to head off stupid comments by interweb know-it-alls. Unfortunately those types will always find something to run someone else down for.
I agree, but he already knew that it was a bad ground because of the dim light. We are taught that electricity runs from positive to negative but ? Electricity much like water is always looking for the easiest path to ground and without that it can be manipulated and or weakened.
OH Eric!! Oh baby! That was fantastic. Absolutely beautimus... the crimping, the soldering, the lead smoke, the fluid film! Let me lay here for a few to catch my breath!
I am so surprised that the ground lug was up top at the front of the vehicle! Chrysler loves to put them at the bottom where all the salt spray can get to them! Good solder job! Thank you Eric and Mrs. O. for the entertainment! 😁
You ain't lying. My buddy's 2016 Cherokee left him stuck on the side of the road. The engine just died and would not start back up. After looking at it, there was a (what used to be) ground strap just corroded to the point of dust in the upper inner wheel well. Brilliant placement.. 🙄
@@Ram14250 The Corolla has been good! That's my daughter's car, but she is telling me she's hearing some braking noise that could just be pads or *might* be a bearing. Not sure. If it's a bearing I will DEFINITELY do a video as I haven't had much to release lately since I did the oil change on the Tacoma and the transmission fluid on the Lexus! Need some content (curse of a part-time TH-camr) 😁
The ONLY thing that matters...and sir I do mean the ONLY thing that matters is that Mrs. O is happy. That said I have to say the sticker "Prtected by manual transmission " is classic! Nice job.
I am a 39 year master tech 13 years at Chrysler ( factory trained) and the rest at BMW,Toyota and Nissan. I will say that BMW and Toyota focused their attention to their electrical training and engineering,Chrysler didn’t but my understanding of wiring diagram’s did elevate me to shop Forman and a better pay check. Great video always enjoyable and your sense of humor is so cool. 😎😎😎😎
found this video posted in a forum after constant trial and error attempts to fix my intermittent blinker. You've saved me one more headache with my '08!
HERE YOU GO AGAIN,,,,,,,,,,,,,,,,,,,,VERY FUNNY AS FUNNY AS IT CAN BE. YOU HAVE THE GREATEST ATTITUDE ON DOING THE JOB IN VERY INTERESTED WAY, AND THE MOST PROFESSIONAL AND TECHNICAL KNOWLEGE I HAVE SEEN IN MY 76 YEARS OF LIFE. POWER TO YOU; JUST WANT YOU TO KNOW BEHIND EVERY SUCCESSFUL MAN IS A GREAT WOMEN, SIR YOU HAVE A JEWEL ON YOUR HAND. PLEASE REWARD HERE EVEY CHANCE YOU GET. MRS. O THANKS A BILLION FOR BEING AN EXAMPLE TO HUMANITY.
Before your appointment with the optometrist, you should know that standard trifocals don't work well under a car, and they are poor for welding and cutting, too. The reason is they rely on the assumption that when you're looking at something up close, you're looking down. Under the lift, you're looking up, not down! It's awkward to find a way to move your head into a position to look down on everything, and I find them confusing while welding. You want something closer to safety readers for work, and maybe trifocals when you're not working. Trifocals can be designed to work well for computer use, which might be a suboptimal compromise.
Every time I hear a horn beep, I say, "Hey, it's Eric!" Thanks for your videos. I watch each and every one of them, even when you replaced the cables on your hoist.
When you stripped the insulation off of the big wire you cut a circle around it to sever the insulation, so technically you circumcised the wire, as the term literally means circular cut. Now you can boast of a new service to your customers! Great video as usual!
2 things Mr O, 1st is this is a family channel, no stripping permitted, lol. 2nd, your repair is better than factory. If it were factory it wouldn’t last. Otherwise another great video, thanks!
Between Ivan (Pine Hollow Auto Diagnostics), Keith (New Level Auto) and yourself, that pretty much covers some of the best in electrical diagnostics. Congrats on nearly 800K subs and on your way to 1M.
as someone told me once, "don't ever assume someone knows what you know". Don't feel that you are diminishing us in any way thinking we know what you know. We dont't. Otherwise, we wouldn't be here. :) Love the content.
My cousin and I flipped cars as teenagers. When someone asked about our guarantee, we told them we offered a taillight guarantee. As long as we can see your taillights, it's guaranteed.
Your repair on the wiring looked better than factory. Only thing I would have done differently would have been to add a small piece of heat shrink to the connection area after lube. This would keep moisture out and lube in.
You taking the time to properly repair a bad ground connection took me back to my early days of trouble shooting tube guitar amplifiers. Start cutting corners here and you're just asking for trouble in the future... 🙂
Just spent 17 minutes of my life not necessary learning how to strip wire and put a new eye on but spent 17 minutes waiting for your sarcasm on various subjects and you didn't disappoint...
@@commietube_censorship_sucks That is mainly due to the steel alloy they used and that crappy coating they devised that holds the salt in. I remember when the first imports hit here in the late 60's and 70's and the cars like the Datsuns and Toyotas that would be totally rotted out in under 10 years because they used a lighter steel alloy. As for the Jeep frames. They were C channel just like most others until recently. They still rot out very fast. But you can get new frames relatively cheap. The aftermarket has gotten to the point now that you can build a complete Jeep CJ without using a single OEM part! (You can also do that with some classic cars, like the model T or A or the Tri5 Chevies and even some others.
@@commietube_censorship_sucks They had a couple boxed areas but most were just stamped C channel with riveted joints. The supposed idea was it allowed them to flex better. The DJ was built a little better than the CJ as it was a contract vehicle.
Soldering and Fluid Film, couldn't be happier! Perfect, better than factory repair. Here in Canada I would spray with ACF50 or Krown, but, you gotta work with what you have, eh!
Hey Mr Eric O. I think you're totally not like our government. Fun to watch and I always learn something. AND you don't solder bad. But I can help you with one small thing. When I was building electronic parts we learned to "tin" the ends of the wires first, before crimping or connecting. Tinning is just adding some solder to the stripped end. It makes a way stronger never cold joint after the final solder to the junction. If I can do it, you can do it. Cheers.
“Marine” heat shrink (incorporating a heat sensitive glue) over the wire and terminal all the way up to the terminal ring can extend the life of the ground point. And a good cleaning of the ground stud will also help. Thanks for the videos!
G'day Eric, I have a mate here in Oz who bought a collectable car, spent many hours fixing the appearance, and then set off for a bi-annual interstate event for these cars. He only got an hour down the road before having to return home because the engine was running rough. He was really down in the mouth about wasting his time and money on this car. I have an Autel that I bought after watching many of your videos, and along with the knowledge you've shared I was able to diagnose a faulty O2 sensor. When he replaced the sensor the car became the best thing since sliced bread. "It really hammers!" So, many thanks to you for your knowledge sharing. It really helps others. South Main Auto rocks!!!
Hey Eric, thanks for adding us girls to the conversation. I'm a retired school bus mechanic, 30+ years. Love your videos and humorous banter. Keep it going
I used to work on a lot of 80s Chrysler products. Number 1 problem? Yep, bad grounds. Followed closely by bad hall effect pickup in the distributor. Some folks took to keeping a spare in the glovebox. 🤣
I had a camshaft position sensor code pop on my '97 Cherokee. Was like WTF? there's no overhead cam in this thing, with a position sensor! Yep - has that same exact hall effect sensor inside the distributor, and that was the cause of the code. It has to synchronize with the crankshaft position sensor for the computer to be happy.
I watched the Prius rear brake video in prep for my day in the garage with "Percy", my admittedly non-masculine but much-valued hybrid. Its purpose in life is to keep commuter, grocery and errand miles off of my expensive truck. Many days/miles between fuel stops doesn't hurt either. Afterward, I stayed on your channel to watch this Jeep turn signal troubleshooting and ground replacement video as well. It's appreciated by this male viewer that you aim the camera at the work being done for 99% of your videos and only chat into the camera for short times to keep the vids friendly and personal. So many vids these days are guys being movie stars who constantly show their face at arm's length (or closer!) and their pointing/waving arm & hand gestures in the frame more than whatever is the subject of their video. It very much appears that you know what you're doing, showed me a couple of tricks with the brake bleed by making use of the Prius' electrically-pressurized brake system (instead of fighting it) and both soldered and spray sealed the ground connection on this Jeep. I like learning from someone who is willing to fix somebody else's vehicle as though it were their own and who doesn't want to deal with the very same problem again later because they said "good enough" before completing a job properly the first time. Have been servicing all of my own machinery since high school in the mid-70s, but still find it encouraging to see someone else go through the steps on screen while I have a cup of coffee and get my game face on for a day in the garage. Then I head out to roll around on a sheet of cardboard with rust flecks falling down my collar and turn the wrenches with a fresh review of a job I haven't done in awhile and maybe even a new trick or two. Well done! Pleasant and informative. Subscriber count = +1.
@0:11 I learned manual on my cousins farm driving the old International pickup on a hill picking up hay at the ripe age of 12! Definitely a lost art!! 😂😂😂
Eric! Great Job! Exactly how I do it. Perfect. The only time I ever got in trouble soldering a wire on a car was: ON MY OWN VEHICLE I soldered the eye on the end of the big wire going to my GM alternator. It had broken, so when I put a new eye on it I soldered it, but it broke in about 2 weeks again. That was because it was a 5.7Liter Diesel. Remember the 350 cid Olds V8 they turned into a Diesel? It vibrated a lot way out at the alternator. So on my 2nd attempt I anchored the wire to about 10 things along the way out to the alternator and that was that. Excellent touch with your shot of Fluidflm. Rust belt benny/ michigan
Thanks for this post! Been chasing this dim signal/no-signal-with-headlights for a few weeks now. Figured bad ground, but with that wire spaghetti behind the pass side headlight, didn't quite know where to start tracing the root cause. With this info, I at least was able to run a temp jumper to that post, and permanent repair forthcoming once I get the new lug!
Your trouble shooting, logic and path to diagnose the problem is amazing! doing the research first as you say is so important, question is where is the best place to get the necessary info say for someone who is only taking care of their own and family vehicles??
PERFECT simile you came up with for the Chrysler grounds there at the end! Couldn't agree with more!! People like you and Mrs. O give me some hope and comfort. Many thanks
Thanks for the information I just had my 2011 wrangler ground fixed the horn and front fender markers lights went out bad ground I was thinking that since I had the jeep Woolwax That maybe it was the Woolwax that was causing bad ground Now I know it wasn`t that but the nature of the beast
Oh man thank you for this video! I’m currently administering hospice care to my 2012 Wrangler and having this exact problem. Thanks to you she won’t die on me just yet!
I used to scratch my head at how a simple bad ground can cause so many crazy problems, until watching your video about that 2019 GM truck that was throwing codes about the trailer towing module and something else just from turning the steering wheel on the electric power steering, and that all being caused by that rusty ground strap. This wasn't so crazy but I probably would have spent twice as long figuring out what to fix.
Huge thumbs up! My jeep has been broken for months with this exact issue, after watching your video I fixed it in about an hour. Thanks for the free knowledge.
Definitely not that first video of yours where the dreaded G102 ground was at fault but I think it is the most accessible of the ones you’ve repaired.😬🍺
Thanks for the video. I had been having the same issue on my 2009 Wrangler. I suspected the ground and had that same ground off and cleaned it. I have been trying to learn more about the electrical side but was close to giving up on this one. I saw your video and went back to the garage and took that ground connection apart and replaced and soldered the connection. It works fine now. Thanks again.
People might say you did it wrong because what they would do is just strip all the wire, wrap it a few times on the stud, and just bolt onto the loose wires like that! Great fix with the right way!
I started my DIY career by buying a 1954 BelAir that the owner had given up on due to failed grounds. That was in 1970. Been chasing failed grounds ever since.
as a 07 jkur owner and having many jeep friends this is a common repair ive done on all of the stud grounds in the engine compartment along that rail there. theres also one on the bottom of the block on the 3.8 with the ground from the battery that has 4 in it and last but not least lets not forget the 2 on each kick panel in the front....i agree with u about the chevy grounds....
I own this one. 2013JK2D and have taken apart the whole Jeep about 3 times so far but I have not fixed that one yet. Thanks for showing me yet another fix and yes I solder all mine back as well. I will say that after I have replaced the suspension, The D30, the shocks, the brakes with a Big brake kit, the control arms with core4x4 HD, The drive shafts, The draglink, the tie rod and trackbar with Steersmarts 1.5 ton HD, The steering with PSC Big bore steering box, the plastic bumpers, ALL the cheap ass lights with JW Speakers, The Radiator, hoses, plugs etc.. the tires and rims and too many other little things to list. The Jeep is perfect now. Runs like a well balanced top. Only cost me about another 15K+ on top of the price of the Jeep. At least mine didn't have the rocker arm issue.
Nice. You said I had to explain how you did it wrong.... I think you should have relocated each ground separately to a different corner of the vehicle, Like left front should be grounded to the right rear, yeah that's it! Oh, and also use a different color for each one with plenty of extra wire hanging around!
So the signal was grounding through the headlight, and therefore dimmer because of the extra load on the circuit. We had a lot of those with trailer tail lights which would work on their own and go out when the signal was turned on,(or the brakes were applied ) .
My first thought was a bad ground. On my 77 E150, I had to run separate ground wires to both front turn signals to keep them working. Also had an issue with the horn losing power.
*Millennial Anti-Theft Device Sticker* - amzn.to/3Wk9Ezi
*Manual Transmission Bumper Sticker* - amzn.to/3Wo4PVQ
*Save The Manuals Vinyl* - amzn.to/43b61hh
*3 Pedals are Greater Than 2 Pedals* - amzn.to/3BDYagC
*Change Gears NOT Genders* - amzn.to/3WkaDzu
Eric O, I've been a subscriber for a looong time and really enjoy your content. But is that last sticker really necessary?
@@nicholaspaul4847 I agree, there is no need for it. Do no harm and live and let live. Like Eric says himself @9:11
Aren’t you you going to take it for a “toot”
I'm a huge fan of the channel and the last sticker threw me off a bit - I didn't expect that from Eric.
I Just Say You Are A Good mechanic I wish you were here in California. But the mechanics out here are very bad they don't really take the time to look at the cars and trucks. I just want to say you're not going to cannock and I love you videos. I have learned a lot from watching your videos and asking questions. Thank you
I'm a subscriber of the female variety, and I love watching your videos. Honestly, I don't care when you talk about the "fellas", or when you say "there's your problem, lady!" I find that last bit super funny. That aside, I have learned so much from watching your videos, especially the ones where you run down electrical issues... I've gotten better at diagnosing issues by following your techniques. Thank you for all your great videos, even the ones you think are silly. Every one of them teaches something new!
Soldering it plus the fluid film will certainly push this repair past the life expectancy of that Chrysler by-product. Great repair as usual Mr. O!
Nothing lasts long in the rust belt 🙄
@@sheerwillsurvival2064 Sure does. Rust.
I thought they are called Stellantis?
@@wolfgangpreier9160 😂 right
@@wolfgangpreier9160 I find my Jeeps have always done good. But I no longer live in the rust belt
Lady with a Jeep here- perfect fix to my problem. Solved in an afternoon. Very much appreciated!!!!!!!
“If only I could see where I wrote the note for the eye appointment”! Lol, sounds like me.
Your experience is impressive. I think you only showed the wiring diagram for our benefit because I don’t think you needed it. You found that bad ground in no time. And the way you repaired it was the same way I would. Nice work.
honestly I think he shows the diagram to head off stupid comments by interweb know-it-alls. Unfortunately those types will always find something to run someone else down for.
@@donakahorse Mouthwrenches 😊
I agree, but he already knew that it was a bad ground because of the dim light. We are taught that electricity runs from positive to negative but ? Electricity much like water is always looking for the easiest path to ground and without that it can be manipulated and or weakened.
Yeah luckily even chryslers breakdowns and failures are reliable! Lol
Yep........not his first rodeo,,,or 50th Man knows his way around a vehicle. Absolutely one of the best there is.
Always entertaining.. And I love how Mrs O answers from across the shop when she barely knows what you said... funny.
OH Eric!! Oh baby! That was fantastic. Absolutely beautimus... the crimping, the soldering, the lead smoke, the fluid film! Let me lay here for a few to catch my breath!
I am so surprised that the ground lug was up top at the front of the vehicle! Chrysler loves to put them at the bottom where all the salt spray can get to them! Good solder job! Thank you Eric and Mrs. O. for the entertainment! 😁
You ain't lying. My buddy's 2016 Cherokee left him stuck on the side of the road. The engine just died and would not start back up. After looking at it, there was a (what used to be) ground strap just corroded to the point of dust in the upper inner wheel well. Brilliant placement.. 🙄
The solder will last longer than the Jeep. Heck, it will probably last longer than Stellantis. Thanks, Eric!
😅
The sticker will last longer than the Jeep.
DIY Dave... need another Corolla video. Find that oil use!!!
@@Ram14250 The Corolla has been good! That's my daughter's car, but she is telling me she's hearing some braking noise that could just be pads or *might* be a bearing. Not sure. If it's a bearing I will DEFINITELY do a video as I haven't had much to release lately since I did the oil change on the Tacoma and the transmission fluid on the Lexus! Need some content (curse of a part-time TH-camr) 😁
The ONLY thing that matters...and sir I do mean the ONLY thing that matters is that Mrs. O is happy. That said I have to say the sticker "Prtected by manual transmission " is classic! Nice job.
I bought a used Jeep and the guy said the local garage quoted him $500 to fix. Watched your video and fixed it myself in about 20 minutes. You rock!
I am a 39 year master tech 13 years at Chrysler ( factory trained) and the rest at BMW,Toyota and Nissan. I will say that BMW and Toyota focused their attention to their electrical training and engineering,Chrysler didn’t but my understanding of wiring diagram’s did elevate me to shop Forman and a better pay check. Great video always enjoyable and your sense of humor is so cool. 😎😎😎😎
wiring diagrams
@@NoName-zn1sb would you accept wiring schematics?
@@johnrpizzaguy
@ No Name is having a snark at the superfluous apostrophe 😊
I can understand why BMW focuses their training on Electrical! lollll They are filled with electrical issues! lolllll
What connector did he use
found this video posted in a forum after constant trial and error attempts to fix my intermittent blinker. You've saved me one more headache with my '08!
HERE YOU GO AGAIN,,,,,,,,,,,,,,,,,,,,VERY FUNNY AS FUNNY AS IT CAN BE.
YOU HAVE THE GREATEST ATTITUDE ON DOING THE JOB IN VERY INTERESTED WAY, AND THE MOST PROFESSIONAL AND TECHNICAL KNOWLEGE I HAVE SEEN IN MY 76 YEARS OF LIFE.
POWER TO YOU; JUST WANT YOU TO KNOW BEHIND EVERY SUCCESSFUL MAN IS A GREAT WOMEN, SIR YOU HAVE A JEWEL ON YOUR HAND. PLEASE REWARD HERE EVEY CHANCE YOU GET.
MRS. O THANKS A BILLION FOR BEING AN EXAMPLE TO HUMANITY.
Before your appointment with the optometrist, you should know that standard trifocals don't work well under a car, and they are poor for welding and cutting, too. The reason is they rely on the assumption that when you're looking at something up close, you're looking down. Under the lift, you're looking up, not down! It's awkward to find a way to move your head into a position to look down on everything, and I find them confusing while welding. You want something closer to safety readers for work, and maybe trifocals when you're not working. Trifocals can be designed to work well for computer use, which might be a suboptimal compromise.
OMG you did NOT insulate that connector properly. J.K.
Long time viewer here thanks for the videos !!!
One of the more enjoyable TH-camrs to watch due mainly to the ongoing commentary, very experienced mechanic is a bonus 👍
Hilarious Sarcasm...just one of the many services offered here at South Main Auto! 😆😅🤣😂🤣😅😆
Guaranteed repair, 5 years or the end of the driveway, whichever comes first.
Thanks for sharing.
Thank you including us ladies! I’ve watched u since u started! I’ll be overriding the VATS chip in my 90’s Corvette probably this weekend! 😊
Nice job on the solder repair. I could see the solder flow on camera. That repair will outlast the vehicle.
2012 and the turn signals dont work? Geez, the signals on my 29 year old 1994 F150 still work fine.😊 Jeeps were good when Willys made them Olive Drab.
Every time I hear a horn beep, I say, "Hey, it's Eric!" Thanks for your videos. I watch each and every one of them, even when you replaced the cables on your hoist.
I’ve breathed that stuff for 50 years! Maybe that’s why I watch you! Crazy loves company!!!
Improper fix! That's better than OEM.
I'm chasing ground connections in my newly-acquired 43' enclosed trailer, so I feel your pain. Thanks!
When you stripped the insulation off of the big wire you cut a circle around it to sever the insulation, so technically you circumcised the wire, as the term literally means circular cut. Now you can boast of a new service to your customers! Great video as usual!
====o Snip!
Uh.....errrr......I think the NY State medical licensing people MIGHT have something to say about Eric offering that particular service!😮
You should see the video of circumcising a battleship.
Hey, its just a snip... until he slips!
@@markh.6687 Do long as he states it's vehicular circumcision so there isn't any confusion.....
Being an individual of the lady variety, I'm sure there isn't a lot of us that watch, but we do.
I like it when he says "there's your problem, lady!" 🤣🤣🤣🤣🤣
There's your problem, lady.
As you should be able to do without comment or stigma. Logical thinking doesn't have a gender.
Guy just shoot the pars cannon from the hip first, then take it to a mechanic. 😅
She ain’t no lady!
I love how vice grips have their own sound....still use them at least once every project...
2 things Mr O,
1st is this is a family channel, no stripping permitted, lol.
2nd, your repair is better than factory. If it were factory it wouldn’t last.
Otherwise another great video, thanks!
Between Ivan (Pine Hollow Auto Diagnostics), Keith (New Level Auto) and yourself, that pretty much covers some of the best in electrical diagnostics.
Congrats on nearly 800K subs and on your way to 1M.
Diagnosedan
as someone told me once, "don't ever assume someone knows what you know". Don't feel that you are diminishing us in any way thinking we know what you know. We dont't. Otherwise, we wouldn't be here. :) Love the content.
Well said. He should quit using ‘assume’ for ‘presume’. He knows his stuff.
I'm so broke I can't pay attention. But I'm trying to catch a damn clue nonetheless...or Moore (ha ha not funny 😑)
@@AndieZ4U2
Agreed. Lol
I had this happen in the early 80's while driving a milk truck. That was how I learned what a failed ground looks like, and how to check it.
That is the best fix and workmanship that I have seen in weeks. That includes Ivan from PHAD.
My cousin and I flipped cars as teenagers. When someone asked about our guarantee, we told them we offered a taillight guarantee. As long as we can see your taillights, it's guaranteed.
Your repair on the wiring looked better than factory. Only thing I would have done differently would have been to add a small piece of heat shrink to the connection area after lube. This would keep moisture out and lube in.
You taking the time to properly repair a bad ground connection took me back to my early days of trouble shooting tube guitar amplifiers. Start cutting corners here and you're just asking for trouble in the future... 🙂
I discovered this channel by finding a previous video on this same problem that popped up on my wife's 2011 Wrangler.
Hiya Mr O super cool video job good job on the repair so please keep them coming GL&HF coming from Dulwich England(✌peace✌)
Just spent 17 minutes of my life not necessary learning how to strip wire and put a new eye on but spent 17 minutes waiting for your sarcasm on various subjects and you didn't disappoint...
Eric after watching you for the last few years. We all trust you 101. I have a decent garage which I trust but even sometimes they make me think FFS.
Love the subtle humor everyone should be equal its 2023. You make it look so easy. Respect
The fact that a frame repair kit is available for those heeps should tell you all that you need to know! Best part of it is that sticker!
To be fair though, the frames on all of them from the early CJs on up are one of the weak points.
@@commietube_censorship_sucks That is mainly due to the steel alloy they used and that crappy coating they devised that holds the salt in. I remember when the first imports hit here in the late 60's and 70's and the cars like the Datsuns and Toyotas that would be totally rotted out in under 10 years because they used a lighter steel alloy. As for the Jeep frames. They were C channel just like most others until recently. They still rot out very fast. But you can get new frames relatively cheap. The aftermarket has gotten to the point now that you can build a complete Jeep CJ without using a single OEM part! (You can also do that with some classic cars, like the model T or A or the Tri5 Chevies and even some others.
@@commietube_censorship_sucks They had a couple boxed areas but most were just stamped C channel with riveted joints. The supposed idea was it allowed them to flex better.
The DJ was built a little better than the CJ as it was a contract vehicle.
Saw a sticker on an armored car today: "Protected by Smith & Wesson".
@@markh.6687 I have that sticker on my toolbox!
Dang Skippy you found that one quick and fixed it very quick dang good😊
Never disappointed watching you do your thing, Mr. O. Still lurking, always watching but rarely commenting, I am. Thanks for all the fish... 🐟
Eric continues to bring us all together in 2023..people..wires..it's all about unity and being well grounded.Way to go Mr. O 😎✌🇨🇦
Soldering and Fluid Film, couldn't be happier! Perfect, better than factory repair. Here in Canada I would spray with ACF50 or Krown, but, you gotta work with what you have, eh!
Hey Mr Eric O. I think you're totally not like our government. Fun to watch and I always learn something. AND you don't solder bad.
But I can help you with one small thing. When I was building electronic parts we learned to "tin" the ends of the wires first, before crimping or connecting.
Tinning is just adding some solder to the stripped end. It makes a way stronger never cold joint after the final solder to the junction.
If I can do it, you can do it. Cheers.
my guess was that there was an LED bulb involved since they can make older cars misbehave. definitely learned how to chase a ground. thanks eric!
“Marine” heat shrink (incorporating a heat sensitive glue) over the wire and terminal all the way up to the terminal ring can extend the life of the ground point. And a good cleaning of the ground stud will also help. Thanks for the videos!
G'day Eric, I have a mate here in Oz who bought a collectable car, spent many hours fixing the appearance, and then set off for a bi-annual interstate event for these cars. He only got an hour down the road before having to return home because the engine was running rough. He was really down in the mouth about wasting his time and money on this car. I have an Autel that I bought after watching many of your videos, and along with the knowledge you've shared I was able to diagnose a faulty O2 sensor. When he replaced the sensor the car became the best thing since sliced bread. "It really hammers!" So, many thanks to you for your knowledge sharing. It really helps others. South Main Auto rocks!!!
Your videos give me a lot of confidence to diagnose my own electrical problems. love the channel
Crimp looked factory to me!! Why would anyone question that repair? Great Job thank you!!
Great fix! Soldering is the key to longevity.
You are an automotive electrical genius...sir!! Love the video!
That was a very appropriate ground fix considering it’s a Chrysler . On par with some VW wiring I have fixed in the past.
Hey Eric, thanks for adding us girls to the conversation. I'm a retired school bus mechanic, 30+ years. Love your videos and humorous banter. Keep it going
Oh my goodness, the brightness of that bulb now.
I used to work on a lot of 80s Chrysler products. Number 1 problem? Yep, bad grounds. Followed closely by bad hall effect pickup in the distributor. Some folks took to keeping a spare in the glovebox. 🤣
I had a camshaft position sensor code pop on my '97 Cherokee. Was like WTF? there's no overhead cam in this thing, with a position sensor!
Yep - has that same exact hall effect sensor inside the distributor, and that was the cause of the code. It has to synchronize with the crankshaft position sensor for the computer to be happy.
DD DD DD 99 times out of a 100 if you keep a spare you will never need it
You should use monovision contacts. One is for reading and one for distance. Some people can't do it but I love it.
Good fix Mr. O.
You said the Magic word and Mrs. O showed up! On to the next one!
I watched the Prius rear brake video in prep for my day in the garage with "Percy", my admittedly non-masculine but much-valued hybrid. Its purpose in life is to keep commuter, grocery and errand miles off of my expensive truck. Many days/miles between fuel stops doesn't hurt either.
Afterward, I stayed on your channel to watch this Jeep turn signal troubleshooting and ground replacement video as well.
It's appreciated by this male viewer that you aim the camera at the work being done for 99% of your videos and only chat into the camera for short times to keep the vids friendly and personal. So many vids these days are guys being movie stars who constantly show their face at arm's length (or closer!) and their pointing/waving arm & hand gestures in the frame more than whatever is the subject of their video.
It very much appears that you know what you're doing, showed me a couple of tricks with the brake bleed by making use of the Prius' electrically-pressurized brake system (instead of fighting it) and both soldered and spray sealed the ground connection on this Jeep. I like learning from someone who is willing to fix somebody else's vehicle as though it were their own and who doesn't want to deal with the very same problem again later because they said "good enough" before completing a job properly the first time.
Have been servicing all of my own machinery since high school in the mid-70s, but still find it encouraging to see someone else go through the steps on screen while I have a cup of coffee and get my game face on for a day in the garage. Then I head out to roll around on a sheet of cardboard with rust flecks falling down my collar and turn the wrenches with a fresh review of a job I haven't done in awhile and maybe even a new trick or two.
Well done! Pleasant and informative. Subscriber count = +1.
@0:11 I learned manual on my cousins farm driving the old International pickup on a hill picking up hay at the ripe age of 12!
Definitely a lost art!!
😂😂😂
Ever since Jeep fixed their leaking rear main seal issues there has been a lot more ground wire corrosion issues.
Comparing Chrysler grounds to the government is the reason I’m here. Keep up the great work!
I have this exact issue even the driver side signal not as bright , and will use this as my guide. Thank you
I love how you troll the trolls. Keep it up Eric O , another fantastic video
Gotta give them something to complain about 😂😂😂
@@coache1nine “ they got what they paid for “
- Eric O
Sure helps out the comment section! 😂
I don’t that type lugs , because they are hard to crimp. But as always you did a great job. Your expertise,once again prevails. Your awesome.
Cool Hand Eric- "What we have here is a failure to terminate."
LOL
Eric! Great Job! Exactly how I do it. Perfect. The only time I ever got in trouble soldering a wire on a car was: ON MY OWN VEHICLE I soldered the eye on the end of the big wire going to my GM alternator. It had broken, so when I put a new eye on it I soldered it, but it broke in about 2 weeks again. That was because it was a 5.7Liter Diesel. Remember the 350 cid Olds V8 they turned into a Diesel? It vibrated a lot way out at the alternator. So on my 2nd attempt I anchored the wire to about 10 things along the way out to the alternator and that was that. Excellent touch with your shot of Fluidflm. Rust belt benny/ michigan
I remember changing the starter on my olds diesel. That thing was huge lol.
Thanks for this post! Been chasing this dim signal/no-signal-with-headlights for a few weeks now. Figured bad ground, but with that wire spaghetti behind the pass side headlight, didn't quite know where to start tracing the root cause. With this info, I at least was able to run a temp jumper to that post, and permanent repair forthcoming once I get the new lug!
Is it wrong if it works? Classic grounding problem solved by "the man" himself. Nice work Eric!
Your trouble shooting, logic and path to diagnose the problem is amazing! doing the research first as you say is so important, question is where is the best place to get the necessary info say for someone who is only taking care of their own and family vehicles??
PERFECT simile you came up with for the Chrysler grounds there at the end! Couldn't agree with more!! People like you and Mrs. O give me some hope and comfort. Many thanks
Looks like what I used to do when I was working, nothing wrong with that repair!!
Thanks for the information I just had my 2011 wrangler ground fixed the horn and front fender markers lights went out bad ground I was thinking that since I had the jeep Woolwax That maybe it was the Woolwax that was causing bad ground Now I know it wasn`t that but the nature of the beast
Oh man thank you for this video! I’m currently administering hospice care to my 2012 Wrangler and having this exact problem. Thanks to you she won’t die on me just yet!
I approve of soldering and crimping. I would have done the same thing on my vehicle. That electrical connection will out live the vehicle.
Great video!!! Simple but very effective repair!!
I used to scratch my head at how a simple bad ground can cause so many crazy problems, until watching your video about that 2019 GM truck that was throwing codes about the trailer towing module and something else just from turning the steering wheel on the electric power steering, and that all being caused by that rusty ground strap. This wasn't so crazy but I probably would have spent twice as long figuring out what to fix.
Huge thumbs up! My jeep has been broken for months with this exact issue, after watching your video I fixed it in about an hour. Thanks for the free knowledge.
Definitely not that first video of yours where the dreaded G102 ground was at fault but I think it is the most accessible of the ones you’ve repaired.😬🍺
Thanks for the video. I had been having the same issue on my 2009 Wrangler. I suspected the ground and had that same ground off and cleaned it. I have been trying to learn more about the electrical side but was close to giving up on this one. I saw your video and went back to the garage and took that ground connection apart and replaced and soldered the connection. It works fine now. Thanks again.
People might say you did it wrong because what they would do is just strip all the wire, wrap it a few times on the stud, and just bolt onto the loose wires like that!
Great fix with the right way!
Jeeps have had lousy grounds dating back to the 80’s. I redid all of the grounds on my 88 Cherokee including the all the sensor ground splices.
Positive feedback: If I can do it, You can do it. My reply: But I can't do it as well as You Sir. 😂
I started my DIY career by buying a 1954 BelAir that the owner had given up on due to failed grounds. That was in 1970. Been chasing failed grounds ever since.
as a 07 jkur owner and having many jeep friends this is a common repair ive done on all of the stud grounds in the engine compartment along that rail there. theres also one on the bottom of the block on the 3.8 with the ground from the battery that has 4 in it and last but not least lets not forget the 2 on each kick panel in the front....i agree with u about the chevy grounds....
I own this one. 2013JK2D and have taken apart the whole Jeep about 3 times so far but I have not fixed that one yet. Thanks for showing me yet another fix and yes I solder all mine back as well. I will say that after I have replaced the suspension, The D30, the shocks, the brakes with a Big brake kit, the control arms with core4x4 HD, The drive shafts, The draglink, the tie rod and trackbar with Steersmarts 1.5 ton HD, The steering with PSC Big bore steering box, the plastic bumpers, ALL the cheap ass lights with JW Speakers, The Radiator, hoses, plugs etc.. the tires and rims and too many other little things to list. The Jeep is perfect now. Runs like a well balanced top. Only cost me about another 15K+ on top of the price of the Jeep. At least mine didn't have the rocker arm issue.
you did it like I do it, plus I spray it with Battery Terminal spary, just for "grins"
Exact issue I'm having! Figured better search TH-cam before I dig in... TH-cam is best tool I have in my garage. Thank you!
Nice. You said I had to explain how you did it wrong.... I think you should have relocated each ground separately to a different corner of the vehicle, Like left front should be grounded to the right rear, yeah that's it! Oh, and also use a different color for each one with plenty of extra wire hanging around!
You gotta love a guy who knows about Bubble Boy. Bright and Shiny!
So the signal was grounding through the headlight, and therefore dimmer because of the extra load on the circuit. We had a lot of those with trailer tail lights which would work on their own and go out when the signal was turned on,(or the brakes were applied ) .
Always learning something new watching your videos. Thanks for the chuckles that come with them!
"Always In A Heep". Great Chrysler wiring strikes again!
Love that sticker!!!! I need some. Anyone know where?
If that ground looks like that imagine the rest of them lol. I knew it was a ground also. You said it at the same time as me. Love you're videos Mr. O
My first thought was a bad ground.
On my 77 E150, I had to run separate ground wires to both front turn signals to keep them working. Also had an issue with the horn losing power.