Whirlpool Washer Not Getting Water. DIagnosis and Repair.
ฝัง
- เผยแพร่เมื่อ 22 ก.พ. 2022
- Call us today with you model number and we will make sure you get the right part
888-655-8569
In most cases we can get you the part the next day if ordered before 4pm central time.
---------------------------------------------------------------------------------------------------------------------------------------------------------------
List of part with links if you happen to need them
Water valve 8 pin - amzn.to/3BH4CCL
Water Valve 10 pin- amzn.to/3BKtqcM
----------------------------------------------------------------------------------------------------------------------------------------------------------------
Links
instagram- / bearded_appliance_repair
---------------------------------------------------------------------------------------------------------------------------
Your Whirlpool, amana, roper or maytag washer not filling with hot or cold water. This video will show you how to test what you need to test to figure out what the issue may be with it. In this case the water valve was bad. We show you how to replace the water valve on this whirlpool washer in this video. Hope this helps, be safe and good luck.
-------------------------------------
Support the Channel by donating or using the links down below.
Try Amazon Business- amzn.to/3ukXqHe
Try Audilbe Plus Free Trial Here - amzn.to/3yx65te
Amazon Prime 30 day Free Trial- amzn.to/3fd7z4g
Donations are appreciated as well you can donate here - www.paypal.me/Beardedappliance
Stop by our Amazon store to pick up must have tools for appliance repair
www.amazon.com/shop/beardedappliancerepair
---------------------------------------------------------------------------------------------------------------------------------------------------------------- - แนวปฏิบัติและการใช้ชีวิต
fixed my moms washer with this video. you are the man, thank you
I cant tell you how happy i am to watch this video...i didnt go all the way but my machine is now working..thanks a million
Thank you so much!! I started having this exact problem after having a water leak at my home. I believe once we got the water back up and running junk from the leak got into the hoses and ruined this part of my washer. I ordered the part for 50 bucks on Amazon, two days later I installed it in five minutes or less and it’s as good as new!
Thanks man! Got my valve from Amazon. 15 minute job. My unit is only 18 months old. No service man in sight. You probably saved me 400-600 cash. I’m grateful.
Thank you so much for this tutorial! Old house, chunks of hard water built up in pipes gunked up the system before I was able to add some filters in the intake hoses. Waiting for the new part (and bought a second to keep on hand for the future.)
Thank you so much!!! This video was PERFECT. Easy fix and only costed $25 for the part.
Thank you so much for making this video!!! :) I have a Whirlpool WTW4800BQ0 that all of a sudden wasn't filling. Not sure what I did, but it's working now. Used your instructions on putting it in diagnostic mode and it worked. Got out of diagnostic mode, and it's working fine now. ???? Thank you sooo much. Before watching this video I was shopping for a new washer. You saved me $1K. You're awesome!
haha i run into these, WOrks for me but not the customer, sounds like a similar issue haha.
This was perfect! Thank you so much!!
Thank you!!!! Saved me so much money thanks to you!
Thank you so much for the instructions. You are a life saver. I truly appreciate it!
Great video! I have this same washing machine and after I ran it through test mode, it started filling again. I didn't have to buy the part which was great. Thank you for easy to follow instructions!
How do you do a test mode
Thank you for your help!
Thank you so so much, I had the exact same issue, your instructions was clear and concise, my only issue was using a painters knife to get the control panel loose, it didn't want to come until I pushed harder and there was an extra spring clip on each side, apart from that went like clockwork. My only downside was, I couldn't wait for delivery so went to a local supplier and picked the part up at double the online price.
Where exactly I can get that part?
Thank you so much for this video!
Great video! Super helpful
Thank you!!
thank you for this helpful video you made it super easy to follow
This worked - thank you!!
he!! yeah
Hope to try
Omg thank you 🙏🏾
Great job my brother Esau
Thanks!
This was SO helpful and easy to follow. Thanks for saving me money and showing me how to take a stab at it before calling someone out. Liked and subscribed!
That's right on saving time and making more money
Yes sir.
Ty
Anytime!
Do you have to run diagnostics once you replace water inlet valve?
Mine exact one here, new, makes a booming sound while filling up with water
During the fill cycle, the drum will spin. I've noticed if it's slightly unbalanced, it will knock into the side a bit and cause a boom. The other thing it could be is your pressure being really high, so it is very noticeable when the valves open.
I was about to throw this machine away , thanks for the tip!!!
😂
Tricked my bastard washing machine! The washer would work on the hot side of things but only slowly out of the cold side. I always wash on cold so I just switched the hot and cold feed in the back of the machine. Now I have the washer set on HOT with cold water running freely. Knowing my luck the issue is probably the board and not this part anyways… simple fast fix if you are only getting water through one side and only want to wash at one temp. Thanks for the video tho!
What would you think if the washer just didn't fill all the way? It fills half way or less it won't do deep water. Same washer
I started with the diagnostic test and the water comes out well but then I go to wash normally and it’s back to no water. Any suggestions?
The same exact washing machine
I get water but only fill up halfway or just one shower so our clothes wouldn't get wahsed right, is this valve also control the amount of water that needed for specific setting?
Thanks in advance
Can you tell me how i know this panel or part is good or no
What the name of that part u installed cause I have the same problem?
How much water does this machine use I just bought a new one of these from Lowes and it only fills to about 5 inches up from the bottom the fabric does when get wet I tried to take it back to Lowes to get a better model but they won't return it and whirlpool won't return it either I've only had it for 5 days need help
Oddly my machine didn't come with a service manual. What's all the lights flashing mean???
So my wash adds water but it doesnt fill up to the level it needs. Would that be a valve problem? All the other cycles fill up as they need. Just the inital wash cycle doesnt get enough water.
I just moved. Used new hoses. Replaced water inlet valve because it was leaking. Attempted to run diagnostics. Lid lock is fine. No water coming from cold hose. What is the problem?
I bought a new water valve put it in and it will pull water but once it shuts off and goes to start putting water in it won't start filling until I turn water off then back on
Oh man I was hopping you had a way to back flush the inlet valve and save us some money. 😢
How do i know this panel is no good
Thank you for the video. Can you post the part number or a link to where the valve can be purchased. Thank you
If you're still looking, he put the links in the description. :)
My issue is it’s not filling with enough water. I always have to do an extra rinse to get the soap out of my laundry.
Love it ty
Think I would have tightened up the packing nut behind the hot water valve
What if my lid locks I hear it throw water fine then it starts humming sound like it's stuck.. but if I run the spin cycle it spins
I have a brand new one and it won't fill up all the way over the clothes what is my problem
I did exactly what did. After the fill mode mine would not switch to wash. Any thoughts at all what to do next?
Needs reset
I’m having this problem. After diagnostic test the hot water works, cold does not. Screen is clean and water pressure is great. Do I still need to replace water valve?
Saaaaaaaaaame problem.
Mine puts water but not enough! Stop the water when is just enough to get the clothes cover but not more 😮
I have a washer like this one but it only ever uses cold water even when choosing hot.
Pressure is good and hot water from the wall works as if I flip the two supplies lines to the wall it'll then only pull hot water and no cold.
Seems like the washer is only ever using the cold valve for the supply regardless of water choice. Any ideas?
Did you find a solution I also have this problem
@@chato209 My wife used 5 gallon bucket with hot water
Another video mentioned that there's a thermostat that prevents you from using water that's too cold (maybe if you live in the north) by adding some hot water even if you have it on full cold. Maybe there are two thermostat or just one that monitors the water from both valves somehow.
I'm having something similar, but it's not all the time. Mostly it won't fill if I leave it on normal wash, but will fill if I change the wash settings. Would that be a valve issue or a control board?
Did you find the issue?
@@amcrodriguez4775 Yes, it was the water valve assembly. Thank you for the video! Saved me a ton! It's working like new now.
OK when I push the button to start my washing machine and when it started trying to put some water in it runs right back out of the hose into the sink in my inside of it is moving real loose. What do I do to fix it?
The inside of it is moving like real real loose like a belt popped off or something in the water running right out of it and I look like my cousin had it all small load for a large load
Can I have the same exact washing machine that you got?
Water want drain out
Man I have to change this thing like every 6 months and it getting on my nerves
Likely the transmission shaft is eating it up. It's change that transmission or get a new one. Changing the transmissions are not as bad as they seem.
Came here since my machine won't take water, While watching this gave a nice whack, hurray it started taking water 😆
My man. I tried your trick and it worked!! Saved me a cool 500 at least.
This shit made my machine even worse 😂 this gotta be the worst washer I’ve ever bought
🤣🤣🤣🤣🤣🤣
@@benjaminfranklin288 you laughing at my pain 🤣🤣🤣
They are junk washing machines! So much for Made in the USA! 😞 I had a Chinese made GE "Little Swan" Front Loader before this that lasted a decade with no trouble, & even though it was about double the cost, it was a much better washer. I sold it, & the dryer b/c they were too big for my current laundry room. The only thing ever had to replace on it it was a water inlet valve, which I did myself.
I just replaced the inlet valve on this one, & it didn't fix my problem. It still won't fill, only fills half-way with cold water (even if you choose hot), & is just a PITA! It's only 4 years old!
This crap isn't doing anything it has power I guess I'll have a go at the door switch