Is the wire from the brake wire coming from underneath the back of the board I just fix mine it was touching yellow and blue was touching now no more noise coming out from the front wheel
Had the same problem. I found that I damaged cables during wheel tube removal/assembly. There was damage in one of the white socket connection cables nearly the end of the black isolation tube.
It's a failure caused by using the regenerative braking while going down hill at high speed. You are supposed to use the rear friction brake with the thumb brake though you can still fry the system if you are going too fast down hill and use both. It overheats the regenerative braking system controls in the main controller and can also fry the motor. Regenerative brakes work by spinning an electric motor backwards. Reversing the motor creates electricity and it is captured and stored back in the system / battery. If you are going too fast and down a hill and use the thumb brake you send too big of a load back into the circuits which overloads the system and basically cooks it. Replace the controller and it should be good. Hope this helps
Disassemble your fork assembley and check the motor wire leads. Sometimes they come loose, I recommend taping them up. Also, try not to use the built in LED light, there is a design flaw that will degrade your scooters electronics, stick to using an external flashlight instead.
Literally just now this happened to me... I have had mine a little over a year now and have almost 340 miles on it and about 135 with it being flashed for speed and throttle algorithm changed to power instead of speed control no loss of range under normal circumstances.. On flat bike path I had to brake from 22mph somebody stopped in front of me. And soon as I hit the brake it sounded like I was going down a ladder.. and buzzed/vibration the 8 miles home. I was waiting for something to catch fire or something. But didn't seem to use any more power than normal.
I've had the same problem with a few of my customers. It's the motor needs replacement. This happened for braking on a descending street or/whit excessive speed or height. If you live up hill don't charge your ninebot over 90-95% the battery capacity. Use mainly the back brake. If the battery is fully charged and the brake is engaged on a steep hill there is no where for that regenerated energy to go. Therefore the engine suffers. Hope it helps.
Disassemble your fork assembley and check the motor wire leads. One of my cables overheated and disconnected. I soldered mine back on and taped it and works like new.
Hey, Genki, did you manage to fix this? UPDATE: It’s the control board, mine was replaced by Ninebot Romania for 85$ + tax for the new control board and 35$ + tax for labour. Plus, I got 6 months warranty for the repair.
check the connector from the controler To the wheel. there are 2 White connector, 1 have 5 pin and 1 pin was in wrong position inside. I Had the same problem before.
I talked to NinebotUS (segway distributor) and they said it was an issue with the regen system. May have overloaded the regen brake on a downhill at high speed~ they said the motor may need to be replaced. I will try your suggestion, but id have to break the warranty seal on the scooter...
@@layeetskeeters9244 NinebotFr know nothing about the problem I did 50 Km now and the bug is not back. for the next step I will put the PIN in the wrong position (the one in which it was at the time of purchase) to see if the problem reproduces. Which would confirm the breakdown.
Real disappointment brought the ES4 Segway December 9 2018 now in February 2019 lights on hoverboard failed began to have electrical problems could not put lights on or would have massive drain on battery now last night the scooter completely stopped working I'm lost don't know what to do won't even turn on and is fully charged
@@p0tat0es_nation64 hahaha you make me laugh.. After you have the same problem now Then hope still you could say that it's a best scooter now with lots of bivrationa and less torque and super noise.. Cause i have d same issue now
its so disappointing that GearBest they are not doing anything I personally had the same issue I did contacted Segway to compline about it, they couldn't provide me with any further information, so be carful everyone, I believe that the new version of Segway big technical issue, my personal advice don't buy it form Gearbest and don't buy the new version Ninebot Segway ES2, you will waist £550 what a shame !
I’ve just encountered the same issue. When breaking its really clunky now - lots of vibration. What is the fix? Is it control board or a wire or a motor issue?
before you buy ninebot you have to be aware consider that they don't provide any guarantee or help or parts you are going to struggle Bigtime to find the parts.
I believe that gearbest they are not doing there best anyway I also was hearing some problem with people who's purchasing from GearBest, that they don't get back to you and many other bought the Ninebote v1.3 with problem so, make sure you don't buy from them, and my personal advice open a dispute via PayPal thats the best solution.
Oh thank god I was about to buy it from gearbest, they have some good promising on regarding warranty and customer service, but I can see that is alllll fake promising, thanks anyway, no ninebote anymore im going for the carbon fibre,
I think it's the same thing... Control board. I took apart the wheel and looked inside.... Nothing. Has to be the control board. because I had mine souped up, and I'm pretty sure it got to hot.
yes I did experience this problem bought my ES2 after 4 week my Es2 has got louder sound then yours and when I brake you can hear crazy sound after that same day in the night I motor stop working, I tried to contact ninebot segway they didn't help me at all they are saying you did bought it from us so I contacted gear best they have also been ignoring me email, so yes its a shit company and a shit scooter, it is strong but it doesn't least with you long my advice DO NOT BUY IT seriously guy I can send you videos to prove that, even though I was trying to buy motor hub you can't find the new version, so yes your going to get F**** by them, trust me every one the scooter is shit I had the carbon fibre and I swear I was going with that scooter every where water driving it like crazy and I was so surprise how strong it was, the only reason I sold that one and bought the Ninebot cuz I thought faster and stronger, it is faster but definitely not strong.
Is the wire from the brake wire coming from underneath the back of the board I just fix mine it was touching yellow and blue was touching now no more noise coming out from the front wheel
Had the same problem. I found that I damaged cables during wheel tube removal/assembly. There was damage in one of the white socket connection cables nearly the end of the black isolation tube.
Omg... it worked. It was the yellow wire. Reattach it and everything was fine again... Thank's
In the botom part of the scooter or in the top? Mine do same noise...
Bro... Random comment to the rescue, it was just that for me as well, was about to take apart the whole motor hub lol, thank you!
Please elaborate. I dont understand
@@rpsgrayfox bro is it in the wheel or in the tube?
i actually like the sound alot
wird klap Hellcat scooter 😂
It's a failure caused by using the regenerative braking while going down hill at high speed. You are supposed to use the rear friction brake with the thumb brake though you can still fry the system if you are going too fast down hill and use both. It overheats the regenerative braking system controls in the main controller and can also fry the motor. Regenerative brakes work by spinning an electric motor backwards. Reversing the motor creates electricity and it is captured and stored back in the system / battery. If you are going too fast and down a hill and use the thumb brake you send too big of a load back into the circuits which overloads the system and basically cooks it. Replace the controller and it should be good. Hope this helps
i was goin uphill with acceleration and foot and after that my motor sounds like it`s broken... iwatroad r6
So basically what, can't use the electric brake comfortably? I was about to buy that shit D:
Hi bro hope u read this. do you mean change the throttle?
It's caused by a wire of the motor (one of the 3 black round plugs) , not the hall sensor. Theses wires move with the fork movement.
did you have the same problem?My es4 makes the same noise 😢😢
Aymji Xwy can you please give more detail on this
Hello Aymji Xwy ! Same problem here, started today. May you post how to fix the problem ? Thanks a lot for share !
Fabricio Paschoal inform me please this is my 4th Segway same problem
@@dreel5659 Hello, I am waiting the answer from Aymij Xwy, what do you mean is your 4th segway with the same problem ?
I was riding mine and going about 17 miles an hour when the front wheel hub just locked up.
I had that too, what was it? Control board
Custom firmware . I shut off the kers. Scooter freewheels and rear brake is used.
I´ve got the same problem after going downhill at max speed, braking hard... ;(
@@cupugaming1182 what to do in that case then ?
Mine did this too then in braked hard again an it went back normal
any fix on this?
I have same problem... I want to find the solution
how did fix it can you help me am having same issue but I didn't fix it
That’s exactly what mine is doing and I only got it today.
Disassemble your fork assembley and check the motor wire leads. Sometimes they come loose, I recommend taping them up. Also, try not to use the built in LED light, there is a design flaw that will degrade your scooters electronics, stick to using an external flashlight instead.
If you look on my channel I posted a video of the noise my scooter makes. Please watch it and tell me what you think. Help is much appreciated.
@@layeetskeeters9244 Elaborate pls? curious
Literally just now this happened to me... I have had mine a little over a year now and have almost 340 miles on it and about 135 with it being flashed for speed and throttle algorithm changed to power instead of speed control no loss of range under normal circumstances.. On flat bike path I had to brake from 22mph somebody stopped in front of me. And soon as I hit the brake it sounded like I was going down a ladder.. and buzzed/vibration the 8 miles home. I was waiting for something to catch fire or something. But didn't seem to use any more power than normal.
I've had the same problem with a few of my customers. It's the motor needs replacement. This happened for braking on a descending street or/whit excessive speed or height. If you live up hill don't charge your ninebot over 90-95% the battery capacity. Use mainly the back brake. If the battery is fully charged and the brake is engaged on a steep hill there is no where for that regenerated energy to go. Therefore the engine suffers.
Hope it helps.
No it is not true..
Sorry
If you change the motor and the noise remain what you do then?
Have you ever solved the problem? Mine do the same noise to 😟
Disassemble your fork assembley and check the motor wire leads. One of my cables overheated and disconnected. I soldered mine back on and taped it and works like new.
@@layeetskeeters9244 i have checked and cables looks fine. Can be a problem from another cable?
Yup
Hey, Genki, did you manage to fix this?
UPDATE: It’s the control board, mine was replaced by Ninebot Romania for 85$ + tax for the new control board and 35$ + tax for labour. Plus, I got 6 months warranty for the repair.
calin thanks for update
check the connector from the controler To the wheel.
there are 2 White connector, 1 have 5 pin and 1 pin was in wrong position inside.
I Had the same problem before.
Hi Sylvain, I have the same problem with mine es4. Even louder noise and vibrations. I will try your suggestion. Thank you
@@TheCvetna can you send us your feedback? thanks ;)
I talked to NinebotUS (segway distributor) and they said it was an issue with the regen system. May have overloaded the regen brake on a downhill at high speed~ they said the motor may need to be replaced. I will try your suggestion, but id have to break the warranty seal on the scooter...
@@layeetskeeters9244 NinebotFr know nothing about the problem I did 50 Km now and the bug is not back.
for the next step I will put the PIN in the wrong position (the one in which it was at the time of purchase) to see if the problem reproduces. Which would confirm the breakdown.
Sylvain Bellanger any luck?
Having the same issue, less than 1 month into owning an ES4.
Real disappointment brought the ES4 Segway December 9 2018 now in February 2019 lights on hoverboard failed began to have electrical problems could not put lights on or would have massive drain on battery now last night the scooter completely stopped working I'm lost don't know what to do won't even turn on and is fully charged
Samn just had this happen to mine. Iv only have it about a mouth also.
Same here too
Just bought a es4 yesterday now it won't power on anymore shut off when I was riding
If only you have this motor sound with normal speed it will be probably the best e scooter!!!
And now I have the same problem on my ninebot scooter...
@@p0tat0es_nation64 hahaha you make me laugh.. After you have the same problem now Then hope still you could say that it's a best scooter now with lots of bivrationa and less torque and super noise.. Cause i have d same issue now
@@throysantiago5384 It was a motor problem and it worked after changing the whole motor. I fixed it like 7 or 8 months ago
So... It means I need to replace a motor?what is actually happened any burn or and parts being removed from inside the motor
@@throysantiago5384 It depends. Sometimes it's the controller.
It’s got a HKS cat back system fitted 😂😂😂👌🏽
Check your motor connectors make sure they aren't melting
Any luck with the root cause of the problem?
its so disappointing that GearBest they are not doing anything I personally had the same issue I did contacted Segway to compline about it, they couldn't provide me with any further information, so be carful everyone, I believe that the new version of Segway big technical issue, my personal advice don't buy it form Gearbest and don't buy the new version Ninebot Segway ES2, you will waist £550 what a shame !
I’ve just encountered the same issue. When breaking its really clunky now - lots of vibration. What is the fix? Is it control board or a wire or a motor issue?
Waiting answe
That actually sounds pretty cool
Can I ask what mount you are using ?
a generic brand gopro mount kit, can be had around 15$ on ebay. am using the original housing the gopro came with (GoPro Session)
before you buy ninebot you have to be aware consider that they don't provide any guarantee or help or parts you are going to struggle Bigtime to find the parts.
I got mine at Costco with a 60 day warranty
I believe that gearbest they are not doing there best anyway I also was hearing some problem with people who's purchasing from GearBest, that they don't get back to you and many other bought the Ninebote v1.3 with problem so, make sure you don't buy from them, and my personal advice open a dispute via PayPal thats the best solution.
Ninebot ecco come rinforzzare ammortizzatore anteriore th-cam.com/video/Vm0lZzGNB3s/w-d-xo.html
Oh thank god I was about to buy it from gearbest, they have some good promising on regarding warranty and customer service, but I can see that is alllll fake promising, thanks anyway, no ninebote anymore im going for the carbon fibre,
You need a new motor
Can anyone read upside down
Output number 4 is the one causing the problem no need to buy the whole control board
can specify that? which output do you mean? thank you!
I think it's the same thing... Control board. I took apart the wheel and looked inside.... Nothing. Has to be the control board. because I had mine souped up, and I'm pretty sure it got to hot.
yes I did experience this problem bought my ES2 after 4 week my Es2 has got louder sound then yours and when I brake you can hear crazy sound after that same day in the night I motor stop working, I tried to contact ninebot segway they didn't help me at all they are saying you did bought it from us so I contacted gear best they have also been ignoring me email, so yes its a shit company and a shit scooter, it is strong but it doesn't least with you long my advice DO NOT BUY IT seriously guy I can send you videos to prove that, even though I was trying to buy motor hub you can't find the new version, so yes your going to get F**** by them, trust me every one the scooter is shit I had the carbon fibre and I swear I was going with that scooter every where water driving it like crazy and I was so surprise how strong it was, the only reason I sold that one and bought the Ninebot cuz I thought faster and stronger, it is faster but definitely not strong.
I have the same issue. Any luck fixing it?
Seems pretty quiet to me.
go and have some operating in your ear was is left or right one ?
This scooter is a piece of shit.