One of the best "how to" videos on TH-cam. The contributor was very thorough and clear on what to do and how to do it. His instructions on reassembly, often missed in other video repairs was concise and helped in not allowing missed assembly and ensured the proper hardware to be looking for.
Window doesnt go down with a dead motor. Here’s how I fixed mine. With my window stuck in the up position I could only push it down a couple inches. I removed the rest of the bolts to the motor and was able to push it down far enough to reach one bolt. I used a small 10mm combo wrench I was able to feel the head of the second bolt and reach it with the loop end of the combo wrench. Although I could only make 1/4 turns, once it was loose I unscrewed the rest by hand. Careful not to drop the wrench or bolt inside the door 😅 After that everything else went well.
For those wondering how to get the bolts out in between the two holes without using the window switch to lower the window, I just manually lowered my window by hand and put tape on the window to hold the window in place so I could access the bolts. You should be able to freely move your window around to see the bolts
Great video! Couldn't have asked for any clearer instructions. My son had been using duct tape to hold his window up until the part came. It took more time getting the sticky residue off than the installation. Thanks again!
Great video! Gave me the confidence to order the part and do it myself. Ours was siezed in the fully up position; we undid the bolts holding the regulator to the door anyway as well as the motor bolts. Once everything was a little freer to move, we were able to get a side-cutters in there (through the hole over the speaker) and cut the cable leading to the top so the window would drop. Just a little help in case anyone else runs into this problem.
Nice video man, me and my mate managed to swap my regulator for my Jdm cl7 euro r in about an hour and half, had its moments . But made it there in the end…
I installed the new regulator exactly as instructed, the window will roll up & down when I press the button, but eventually it'll just stop working, I originally thought maybe the window gets caught on something when going up & down, which it was at first but once I fixed that, I was testing to see if the window worked & it did for a few seconds than it just stopped working again. I'd unplug the regulator & plug it back in & it would work again but for a few seconds...maybe a defective regulator?
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
What if my window doesn’t roll down at all 😪 how do I get to the bolts
One of the best "how to" videos on TH-cam. The contributor was very thorough and clear on what to do and how to do it. His instructions on reassembly, often missed in other video repairs was concise and helped in not allowing missed assembly and ensured the proper hardware to be looking for.
Thank you. I can't wait to make this take 10 times as long as you.
Window doesnt go down with a dead motor. Here’s how I fixed mine. With my window stuck in the up position I could only push it down a couple inches.
I removed the rest of the bolts to the motor and was able to push it down far enough to reach one bolt.
I used a small 10mm combo wrench I was able to feel the head of the second bolt and reach it with the loop end of the combo wrench. Although I could only make 1/4 turns, once it was loose I unscrewed the rest by hand.
Careful not to drop the wrench or bolt inside the door 😅
After that everything else went well.
For those wondering how to get the bolts out in between the two holes without using the window switch to lower the window, I just manually lowered my window by hand and put tape on the window to hold the window in place so I could access the bolts. You should be able to freely move your window around to see the bolts
The whole purpose of the video is to change out the defective regulator. How do you expect someone to roll the window down to access the 2 10mm bolts?
Great video! Couldn't have asked for any clearer instructions. My son had been using duct tape to hold his window up until the part came. It took more time getting the sticky residue off than the installation. Thanks again!
Great video! Gave me the confidence to order the part and do it myself. Ours was siezed in the fully up position; we undid the bolts holding the regulator to the door anyway as well as the motor bolts. Once everything was a little freer to move, we were able to get a side-cutters in there (through the hole over the speaker) and cut the cable leading to the top so the window would drop. Just a little help in case anyone else runs into this problem.
Best video instruction ever! I’ve watched many
this helps a lot thank you
Guy is a legend
Nice video man, me and my mate managed to swap my regulator for my Jdm cl7 euro r in about an hour and half, had its moments . But made it there in the end…
I installed the new regulator exactly as instructed, the window will roll up & down when I press the button, but eventually it'll just stop working, I originally thought maybe the window gets caught on something when going up & down, which it was at first but once I fixed that, I was testing to see if the window worked & it did for a few seconds than it just stopped working again. I'd unplug the regulator & plug it back in & it would work again but for a few seconds...maybe a defective regulator?
Great Video, best tutorial ever
Thank u bro
Thanks very helpful
thanks
car locks have been altered as well as the auto window. disconnected the battery and waited, auto window returned. door locks... not
Where purchased cat ??
So how do I get to the bolts since it doesn't roll down