Thank you so much for your video I was hitting a wall with this problem then I saw you video and Breathed a sigh of relief your video was a break through for thanks again. It worked perfectly for my 10th gen Honda Civic
Excellent Geniusely straight to the point well put together video with no gratuitous inauguration. This video will immensely be of enormous help to other viewers as was with me. Actions for sure speak louder than words. @other TH-camrs hop you will acquire same inspiration from this and start to came up with more smipler straight to the point videos.
Agreed on meaningless chatter. I started watching another video and he had to talk about his chickens first. I turned it off immediately ha ha then found yours
Good instructions, just one suggestion foe improvement: zip tie wires between two horns to car chassis to prevent wires from vibrating in wind flow when driving, which can cause wire end terminals to come off from horn terminals.
The circuit (wires) are only sized for one horn. Use it to power a relay instead, then use a larger wire from the battery tru the relay (fused) to power the horns. TWICE as loud.
Very good! I am hoping to add super loud "trainHOrn" but want to keep my original for minor infractions and courtesy honks. I want to wire a button in the car, maybe left foot activated under the dash. I assume I can run a wire off the positive battery terminal, through the firewall, to a switch. then run back through firewall to the positive on the horn. The negative on the horns goes to the car body/ground or the negative terminal. correct?
Thank you for the great video. How do you tell which connector on the replacement horn is positive? i bought from Bosch, but there is no marking to differentiate between positive and earth. Do these horns not have polarity? Thanks!
What abt the original horn It looks as if one has to disconnect original horn and connect new horn Can wenot have both horns.....old and new extra horns? Do we have to fix a separate switch??
I’m gonna try this tomorrow with the new horn I just purchased from Autozone! It’s the: “SureBilt 12 Volt Standard Dual Tone Horn,” but there’s NO INSTRUCTIONS! 😮
i have install a 5pin 30A relay.. dunno why my horn sometime will delay when i emegency horn no sound need press few time just horn? any one know what the problem?
Sir, I want to install hella chrome twin horn in my wagon r vxi 2015 model which has single horn...I have a doubt... whether relay need to purchased for installation or just horn set is enough? Some people saying relay is must , some say not required.pls clarify my doubt...thanks in advance
The high tone of my car's old hella trumpet horn got shot. So installed a new set of high and low tone trumpet horns. But the old low tone seems to be working fine. So can I install this old low tone along with the new high and low tone's? It's already fitted with a relay.
Have you had a chance to work with Hyundai or Kia horns? They come with special connectors, which are not available anywhere. Looking to add a high tone horn to the single low tone horn on new i20 without cutting wires. Any pointers on how to do this?
Sorry when you connected the BLACK wires and then you connected the two black wires on the (Right) second horn; it does not show which wire you connected to (Colour) as they are both black or it doesn`t matter where you connected to on second horn ????
Excellent video, thank you! 1 question, my 2 new horns came with a 4-pin relay. I will watch your relay video next, but what's the purpose of installing the relay when you can simply wire 2 horns like you did on this video? Again, this video was clear and great quality, perfect length, and nice music too! :)
@@vishalahinave Thanks for your rapid response. Okay, I will go without relay. Do you know, how to install a car remote locking buzzer/siren/speaker? I appreciate, If you could share me any info, URL links or leads about it.
@@vishalahinave I've central locking system provided by company but nano doesn't come with any buzzer/siren. Everytime I lock the nano doors with remote, I can see only the indicator lights blink twice but no sound. So I was looking for info "How to install a buzzer/siren for central locking". Do you think you could help me?
Will there be any issue with out using relay?... My car is a 2019 model santro.. Its having single horn... Roots windtone is installed today.. But its working fine.... Will there be any hazard issue?
How do you know which one of the two terminals on the horn, is the positive, and which one is negative? on the ones I bought there's no marking. Also, don't you need a relay?
Hello there. I am a little confused about this installation. When you disconnected the old horns you had one you had two wires connected to the old horn. One is supposed to be a positive and the other ground... Am I right? Please let me know. Thanks.
Brother i saw your video . I have toyota etios with double horn... I really want these horns but the thing is i m afraid if i need a relay or not. Plzz tell me should i use relay or not???
Thank you so much for your video I was hitting a wall with this problem then I saw you video and Breathed a sigh of relief your video was a break through for thanks again. It worked perfectly for my 10th gen Honda Civic
Clear,to the point,basic and very easy to duplicate..nice video my guy..😎
Excellent Geniusely straight to the point well put together video with no gratuitous inauguration. This video will immensely be of enormous help to other viewers as was with me. Actions for sure speak louder than words.
@other TH-camrs hop you will acquire same inspiration from this and start to came up with more smipler straight to the point videos.
This video saved me countless hours of working on a horn install , thank you 🙏🏽
Straight to the point. No useless new wiring from battery and a relay needed.
Brilliant. Simple and clear instructions. Nice audio without meaningless chatter. Will be doing this tomorrow. Thank you.
Agreed on meaningless chatter. I started watching another video and he had to talk about his chickens first. I turned it off immediately ha ha then found yours
Amazing such a simple job but nobody else shows how to do it on You Tube but you.
Thank u. No need to talk very easy to understand. Just perfect for me.
Bhai ese splendor Plus bike mai laga saktey hai kay
Dear viewers, please use a horn relay to get the exact output. This can't be seen anywhere in this video.
Is it so, what is your advice, Vishal bhai?
Isn’t he already using the factory relay? Why would you need 2?
@@Alsop4lifep
@@Alsop4lifethats what i thought 😅😅😅
Most modern cars have a horn relay already but if anyone still added another and experienced improvement it would be good to know.
Just installed my bosch horn with your video..works great..thank you!!!
I have searched all day for this video thank you so much
Should be tinning and soldering those connectors with heat shrink tbh. Any other changes to your fuses?
Good instructions, just one suggestion foe improvement: zip tie wires between two horns to car chassis to prevent wires from vibrating in wind flow when driving, which can cause wire end terminals to come off from horn terminals.
Good idea. I was thinking something similar
Thank you for this! You just saved me a tone of money💯🙏
Yeah, nice short video!
Two tones!
One of my horns works I’m going to try adding two more, they come in sets hope I get a nice annoying blast.💥
Love you're voice. Did they have a positive and negative terminal❓❔
5 years later first time seeing January 6 2025
I seen this 2 days ago
The circuit (wires) are only sized for one horn. Use it to power a relay instead, then use a larger wire from the battery tru the relay (fused) to power the horns. TWICE as loud.
Asking for trouble if you don't use a relay.
Very good! I am hoping to add super loud "trainHOrn" but want to keep my original for minor infractions and courtesy honks. I want to wire a button in the car, maybe left foot activated under the dash. I assume I can run a wire off the positive battery terminal, through the firewall, to a switch. then run back through firewall to the positive on the horn. The negative on the horns goes to the car body/ground or the negative terminal. correct?
Hello how about the ground wire where is that.
Thank you for the great video. How do you tell which connector on the replacement horn is positive? i bought from Bosch, but there is no marking to differentiate between positive and earth. Do these horns not have polarity? Thanks!
Thanks!
Damn this video was relaxing.
Prefect video.... Very clear installation... Thank you
What abt the original horn
It looks as if one has to disconnect original horn and connect new horn
Can wenot have both horns.....old and new extra horns?
Do we have to fix a separate switch??
Thank you for sharing this @Vishal Ahinave. I will follow this instruction to install my extra set of Audi horns on my Toyota truck 👍👍
Hello does this works in Hyundai Elantra 2016
Just did this to my toyota yaris ia! Works great and horn sounds so much better!
Dude, way easy to understand. Your amazing. Im going to do this on my bike.
Did you try it?
I'm going buy horn is it good ...
Hello do you need a relay or a fuse?
Thank you sir this helped me immensely on my atom2
HELO FROM ROMANIA 🇷🇴 GOD JOB
Wich one horns better metal or hard plastic
Without rely horn laga sakta hu kia sir Omni van par ?
Just want to ask if it is safe to use without relay and fuse?
With out cut out its work?
I’m gonna try this tomorrow with the new horn I just purchased from Autozone! It’s the: “SureBilt 12 Volt Standard Dual Tone Horn,” but there’s NO INSTRUCTIONS! 😮
i have install a 5pin 30A relay.. dunno why my horn sometime will delay when i emegency horn no sound need press few time just horn? any one know what the problem?
Excellent... Neat job.. Direct to point.. No bakwas,, ❤️💓💓👌🏼👌🏼
Relay Bina kya ye safe honga ya nahi
Company fitted single horn. Double horn lagane me relay ki jarurat nhi h kya ?
No ground? Or is it built in with your set up.
Sir, I want to install hella chrome twin horn in my wagon r vxi 2015 model which has single horn...I have a doubt... whether relay need to purchased for installation or just horn set is enough? Some people saying relay is must , some say not required.pls clarify my doubt...thanks in advance
The high tone of my car's old hella trumpet horn got shot. So installed a new set of high and low tone trumpet horns. But the old low tone seems to be working fine. So can I install this old low tone along with the new high and low tone's? It's already fitted with a relay.
Does this conversion require a Relay? If so, what specifications on the Relay so I know which kind to buy? Thank you.
How do i connect hightone Audi horn to Opel Corsa B?
Bro can we connect 4 horns like this please reply 😊
Can u install horn high first & then low?
Yes sequence doesn’t matter
This should work fine on motorcycle set up too yea?
Yes but with relay
Can a 12v and 24 v be connected in series/ duel horn setup
Is Relay required for this dual tone Horn? ? ?
I have 2020 model Renult Kwid do I need to install relay??? It only has single horn
Yes you need
Have you had a chance to work with Hyundai or Kia horns? They come with special connectors, which are not available anywhere. Looking to add a high tone horn to the single low tone horn on new i20 without cutting wires. Any pointers on how to do this?
No need relay?
Sorry when you connected the BLACK wires and then you connected the two black wires on the (Right) second horn; it does not show which wire you connected to (Colour) as they are both black or it doesn`t matter where you connected to on second horn ????
I have tiago 2021, want to upgrade it to polo horns, does riley required?
Yes required
Have you managed to install the Horn to your Taigo ? Everything works okay ?
So a parallel config is better then a series config?
My new Bosch horn are not working I have installed then same as in video plz suggest
Not relay used
Car Santro 2012
Use relay
Digram → 30 Connect Battery
87 horn
85 and 86 stock horn wire
As relay is already present in car we just need to carry wires to 2nd horn. In case horn doesn't work we need to adjust the horn screws.
Great video!! Do you need a relay for a 2014 corolla or will it work like in your video? Thank you!
Car already has a relay buddy it should work.
@@vishalahinave really
Excellent video, thank you! 1 question, my 2 new horns came with a 4-pin relay. I will watch your relay video next, but what's the purpose of installing the relay when you can simply wire 2 horns like you did on this video? Again, this video was clear and great quality, perfect length, and nice music too! :)
installing a relay is safer, it will not "surcharge" the original horn wiring harness ;)
@@sprintertrueno1985 we wonder if that model the writer is speaking of addresses the potential surcharge concerns
An extra relay would help prevent overloading the original circuit.
Hasn't the original power-feed used here, already got a relay and fuse..?
Hi Vishal,
Thanks for making an informative video.
Can I install them without any relay to tata nano or relay in required for nano cars?
Yes you can install without relay
@@vishalahinave Thanks for your rapid response.
Okay, I will go without relay.
Do you know, how to install a car remote locking buzzer/siren/speaker?
I appreciate, If you could share me any info, URL links or leads about it.
For that you should go for central locking system or security system which comes with remote locking and unlocking
@@vishalahinave I've central locking system provided by company but nano doesn't come with any buzzer/siren. Everytime I lock the nano doors with remote, I can see only the indicator lights blink twice but no sound. So I was looking for info "How to install a buzzer/siren for central locking".
Do you think you could help me?
@@JohnsonYesudasAnthony so simple please watch my video for installation siran th-cam.com/video/Jo5nEumoaSs/w-d-xo.html
Excellent video! Subscribed!
Thanks for great video, I was well stuck🎉😊
Is it work without relay ?
Excellent video. Thanks for showing us. 😎
you need to detach the battery before doing this, right?
Ye horn hm pulsar m use v kr skte h
Yes, but you need relay.
@@vishalahinave brother eon car mein relay lagana jaruri hai kya
No
@@vishalahinave meine actualy lagwa diya hai relay koi problem to nahi hai naa
No relay required?
Bhai Bosch ke horn lgvane pr relay lgvana jaruri h kya
Yes
Very clear video. Nicely done !
Can you use 12 awg speaker wire for this application?
You can use any wire
@@vishalahinave Thankyou! I just got dual horns installed on a 2019 honda civic. Sounds great compared to the old "meep"
@@edcko10 did you use a relay or directly connected to OE horn wire?
Bro eth horn aan better bosch or hella?
No relay needed??
Como se llama ese claxon ?
Does it have positive or negative?
No polarity issue
my hyundai venue has different stock plug..its not dual wire and pin like urs...what to do?
Your horn has one positive wire and its grounded by the bracket.
@@vishalahinave where can i send u the pic of wire...u can then guide me for instalation
This is my whatsapp number 9767302189
Will there be any issue with out using relay?... My car is a 2019 model santro.. Its having single horn... Roots windtone is installed today.. But its working fine.... Will there be any hazard issue?
With relay it will sound good
is it safe without relay and fuse
I use it without relay in my dzire
Did you add another relay or the OEM relay in the fuse box?
No relay was added
Is it necessary to use relay for upgrading to dual horn from single? If yes, how does it affect ?
Yes it is. Without a relay the horns will sound softer and also you could damage the switch or blow the fuse
there's no relay?
How much price
Bhai kitne mm² wire use kiya h black
1
@@vishalahinave 1.25 ya 1.5 le skte h
Yes le sakte hai
@@vishalahinave ye wire jo house wiring mein use hota h vo h ya automotive wire ?
House wiring
Bhaiya kitna ka horn
Hi..can this also he applied for wigo 2020?or doni need a relay and fuse?thank you for the video
Can be installed without relay
Love the video ,now I will do this set up on my Himalayan ,thanks brother
How do you know which one of the two terminals on the horn, is the positive, and which one is negative? on the ones I bought there's no marking. Also, don't you need a relay?
I'm pretty sure it doesn't matter
Hello there. I am a little confused about this installation. When you disconnected the old horns you had one you had two wires connected to the old horn. One is supposed to be a positive and the other ground... Am I right? Please let me know. Thanks.
Exactly one is positive and the other ground
No polarity there.
Sir car m jo horn lga hota h phly titi wala uski 2 luppia hti hy meri Car m dono titi waly horn p1, 1 luppi lii h
Can only low tone horn be used as I don't want to be it so loud
Yes you can use
@@vishalahinave sound output will be less or medium
It will be similar to stock horn
My Celario Zxi come with single hella low tone hone I want to install hella low tone and high tone horn without relay it's possible or not
Yes possible as my setup is similar low and high tone without relay works well.
With out relay any pronlem
Brother i saw your video . I have toyota etios with double horn... I really want these horns but the thing is i m afraid if i need a relay or not. Plzz tell me should i use relay or not???
Using a relay will be good
@@vishalahinave thanks bro
Will it work on bolero slx2009 model??
Yes
Sir Reley Kya Hota Hai ? Agar Hum Use Na Kare To Horns Ki Life Kam Ho Jati Hai Kya ?
More than that lil beep she had...awesome...im doing it too..👍😎
Did it the same way like video and sounds great on a 07 honda 1300 vtx. Saved me money thank you very much brother. Happy Holidays. Orale
Which is better hella Or bosch dual horn??
Both are good
Relay?
My Renault kwid has one horn and a stock relay. Will it be enough to fix these both horns? Please help!
Yes simply replace the stock one with these 2. I have kwid too I will upload video if possible.