Super helpful video, do you have any tips about how to get the front lower arm back into the end alignment? Got the ball joint in the spindle and attached back to the shock, but just cant get it back into the final back alignment to screw in
I noticed you did an alignment a few months before this job. 2 questions: Did you change the driver's side as well? Did you do alignment after this job?
I used this one: www.amazon.com/OEMTOOLS-26553-BALL-JOINT-SEPARATOR/dp/B0955H22QD/ref=asc_df_B0955H22QD/?tag=hyprod-20&linkCode=df0&hvadid=532546161982&hvpos=&hvnetw=g&hvrand=4394053596716579959&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9003205&hvtargid=pla-1423949755333&psc=1
Hello ✋🏻, i need your advise please. My ride is Audi A4 2006 2.0L ... I had a complete set of control arms replaced today (total 10pcs), and being aligned afterwards, but unfortunately i experienced a very stiff steering wheel. Any clue ?
Hey Dave, thanks for replying . In fact, i left the mechanic garage and drove 16 km to home. And its insanely stiff. Do you believe i should give more time ?
Was there before replacing the suspension?? Check the u joints of the steering column inside and outside the car , if u have steering wheel light on can be some malfunction on the steering on electric rack
@daveraymond2265 really good video. Did you had any vibration in the steering wheel while braking? Got a knocking noise from the front while I drive slow and slightly press the brakes through potholes or pull hard and when I'm doing 70mph and press the brake I get a bit of vibration in the steering wheel. Thanks
Why did you replace the entire control arm? My independent German vehicle mechanic said that I need to replace the entire arms because all of the bushings are shot. Why not just replace the bushings? He’s quoted me over $900 for the job.
My issue was a worn and loose outer ball joint which is an integral part of the arm and cannot be replace separately. If your bushings are shot then the ball joint is probably not far behind. The entire arm cost $125 from Autozone. A Genuine Audi control arm will cost you $440. I think $900 is a bit much and probably what a dealership would charge if not more.
![Comment remplacer un bras de suspension avant sur Audi A4 B8 Berline [TUTORIEL AUTODOC]](http://i.ytimg.com/vi/-601fpXPJDs/mqdefault.jpg)
![รวมเพลงลูกทุ่ง 6 หนุ่มไทบ้าน ฮิตติดกระแส ชุดที่ 1 l มนต์แคน ไมค์ ไผ่ เสถียร ไหมไทย พี [Longplay]](http://i.ytimg.com/vi/GD2v1OjMw5I/mqdefault.jpg)
![[TH] 2024 PMWC x EWC Group Stage Day 3 | PUBG MOBILE WORLD CUP x ESPORTS WORLD CUP](http://i.ytimg.com/vi/VnOqutfqWqU/mqdefault.jpg)
Super helpful video, do you have any tips about how to get the front lower arm back into the end alignment? Got the ball joint in the spindle and attached back to the shock, but just cant get it back into the final back alignment to screw in
Very good instructional video. 👏
Thank you Stephen 👊
I noticed you did an alignment a few months before this job. 2 questions: Did you change the driver's side as well? Did you do alignment after this job?
do yu have the link for those control arms I have the same year but I bought ones with wrong ball joint bolt size please thanks
same here
Didn’t you have to torque it at ride height? or is that on the other arm? Referring to the straight one
You only need to torque the inner bolt at ride height. The inner bolt uses a rubber bushing. The outer ball joint can be torqued anytime.
What ball joint separator did you use? There are a lot of them where the fork won’t fit.
I used this one:
www.amazon.com/OEMTOOLS-26553-BALL-JOINT-SEPARATOR/dp/B0955H22QD/ref=asc_df_B0955H22QD/?tag=hyprod-20&linkCode=df0&hvadid=532546161982&hvpos=&hvnetw=g&hvrand=4394053596716579959&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9003205&hvtargid=pla-1423949755333&psc=1
Hey, mine barely fit on the side of the bolt and it ended up breaking the bolt at the same time it came out. Sounded like a gunshot.
Hello ✋🏻, i need your advise please. My ride is Audi A4 2006 2.0L ... I had a complete set of control arms replaced today (total 10pcs), and being aligned afterwards, but unfortunately i experienced a very stiff steering wheel. Any clue ?
Is it possible your wheel just seems to be stiff because you now have all new tight ball joints or is it unusually stiff?
Hey Dave, thanks for replying .
In fact, i left the mechanic garage and drove 16 km to home. And its insanely stiff. Do you believe i should give more time ?
@@hanksdinelli2480 no that doesn’t sound right I have replaced every control alarm on my ‘97 A4 and it steered beautifully
@@hanksdinelli2480 if it is insanely stiff something is binding and if you continue to drive it like that it will just wear out whatever is binding
Was there before replacing the suspension?? Check the u joints of the steering column inside and outside the car , if u have steering wheel light on can be some malfunction on the steering on electric rack
Hey thanks is it the same as Audi Q5 2008 3.0 TDI ?
The part states that it fits 2009-2010 Q5, so its not exactly the same.
How much was the control arm? Thank you
I think I paid about $150 for it.
It was not an OEM part.
where did you get it? and was the ball joint smaller than the original?
What symptoms were u having that led u to change it out?
Clunking over bumps
@daveraymond2265 really good video. Did you had any vibration in the steering wheel while braking? Got a knocking noise from the front while I drive slow and slightly press the brakes through potholes or pull hard and when I'm doing 70mph and press the brake I get a bit of vibration in the steering wheel. Thanks
Hey I’m having the same issues with my Q5, did you end up figuring it out? If so any tips you can offer me? Thanks !
Why did you replace the entire control arm? My independent German vehicle mechanic said that I need to replace the entire arms because all of the bushings are shot. Why not just replace the bushings? He’s quoted me over $900 for the job.
My issue was a worn and loose outer ball joint which is an integral part of the arm and cannot be replace separately. If your bushings are shot then the ball joint is probably not far behind. The entire arm cost $125 from Autozone. A Genuine Audi control arm will cost you $440. I think $900 is a bit much and probably what a dealership would charge if not more.
☹️ Ｐｒⓞм𝕠𝕤𝐌