วีดีโอ

Hey, loved the way you presented🙌! I'm not really sure if it is the best time to ask but, I was wondering if I could help you create a better distribution by working on post-production like better storytelling through Edits, Keywords, think catchy intros and outros, or even some engaging short clips! Would love to chat if you're interested and keep creating good content:)

Anyone else had this issue who also have the sound it makes before the fix. I have a ticking sound on my 09 4.6, but it's mostly under load, no check engine or any error codes.

Only two bolts are goin back in, believe that!!

Now get it back it…😂

I just need to change almost 1/2 the spokes on the inside of my fat tricycle drive wheel ,and I’m not able to trace where the spoke came . My whole problem is spoke placement and the wheel can’t be taked off because it’s welded on that’s what happened to the spoke that need to be replaced the welderr popped them

I struggled all day to remove 2 such gaskets. Ended up building a dedicated tool!😂 When you remove a fork, don't neglect dismantling it completely and check the upper tubes...

Small suggestion for the next run... use a lighter color drip bucket so you can make sure the fuel is a good clean red. Sludge problems will show when you change the filter but they're hard to see in a pan that dark.

Awesome pfp man

thank you so much this was the best video on replacing the timing belt on the audi 2.8, this gave me confidence to do it myself because i unsure about so many things.

Great place to start, I took the wheel liner out too to get better access. I also switched to a 1/4 inch drive ratchet after I broke it loose so I had more swing room. Also do the top bolt first so the starter is not binding making it harder to move.

Take this from a retired machinist… your measuring tool is not a micrometer, it’s a Digital Caliper. That said, good to see you using that instead of a Tape Measure!

Anyone knows the bulb replacement #?

Very good educational video 👍

Thank you. I used the cap and seal the end of the tube you cut off and all is well...

I googled "honda lane switch target" and downloaded the first picture and printed it off. I set up my ladder and taped the target to a cardboard box. I tried to position it near the same place he had his. First try...success! Big help dude. Big help! I agree with the other commenter who said that if the collision place didnt calibrate it that means they did not test it after the repair....thats a problem

How much is the full pump 2010 q5

Very informative. Just had my new ones delivered for a 98 Foreman 400fw plowing quad. Looks like the same setup as yours 👍👍

Budweiser uuuuum good!

Hwy bro, great video. FYI, I have started diluting the Brake Buster To 5:1 with the foamer. Instructions don't say to do that of course, but I've cound I can pre foam my car and clean the rims, barrols etc because the foam just hangs and dwells. There is zero difference in cleaning ability at that cut with the foamer.

Would this fix the door not opening from the outside?

Thanks for this! Been about 10 years since I laced a wheel and I was having trouble remembering how to start. Very helpful! And I'm also working with a 70's Honda wheel.

Thanks! Flipping hidden screws!

Thankyou for uploading this video. Very informative and you explained how to get the wheel even in forks when you don’t know the offsets. I have had some rims replaced but they sit over to one side and not in the middle. Spacers are correct so it’s the offset. Would the best way to get them even be to restart the process or loosen 1 side and tighten the other until they are centred?

Thank you for such a thorough process. You gave me confidence attempting myself. 👍👍👍

What shocks are they ?

Have you had any issues with the electronic steering and electronic deck lift? I'm looking at a GTX2154 with around 400hrs.

Just change the bolt ... just go and get a new correct sized "sholded bolt" ...... FFS

Perfect video, at the perfect time! Thanks for being so thorough in covering the entire process! Cheers!

My q5 engine bay is super dirty from back road trips. I’m super nervous to do this and worried I’ll mess up something. How many times have you done this. Is this truly safe ?

Good Job Dave, nice mower! Have an LT 2042 here to service, like yours it looks like new! Love Cub Cadets. From Sophia, N.C.

When you finally got the OK, how far away was the target from the car, how far away was the camera from the car, and how high was the top row of dots? Without that information, the rest is just wasted.

Clean contacts of misfiring cylinder connector, check plug condition and gap(correct if necessary), add injector cleqaner to the gas. If these don't work, swap coils to isolate it.

Thanks for the video! 🙏

How far away from the car do you set the target?

but how to put belt back on? 😂

Finally! Someone who shows and explains these issues. Just wishing to hear sound before fixing. Still great video)

I wonder if it’s possible to drill through the top like the pro +

Nice work on the video, very helpful to me in getting my TL timing set. Thank you

My 2015 SQ5 used a standard Phillips screw, not the Torx style, look closely before you purchase a T-25 Torx screwdriver.

What was the ratio of water to degreaser?

I added Schrader valve. I made sure the valve wasn’t underneath the handle.

So my clutch fan broke and the blades punctured my radiator. So I had to order a new radiator as well as new fan motor and blades. I heard you saw you don’t run the fan so I was just wondering if there is any issues like overheating or running hot in general? Would greatly appreciate any insight lol 😊

I like it

Did you listen with a mechanics stethoscope and pinpoint the noise?

Please what is the number of the timing belt I could use for mine

A BIGThanks to you... I was messing around in the secret setting and messed up my camera alignment. With your specific advice, I restore my camera to a working state after two tries.. I won't be messing around with any more settings. lol

Same problem with my Audi, only... The motors on my lock are manufactured with the Brushes at the Drive end of the Motor, and there's no way of getting the drive gear off the shaft to get to them. I can see the commutator is messed up but can't get to it to clean it all up. (A3 2013 8v)

Great job and i love the blue tooth Autel I have the MX808 but it’s hardwired to the OBD2 cable..having scanner at where you are working is really helpful. Great job in getting the sensor out .. with all the corrosion I was thinking it’s going to snap, I have ‘13 Jetta wagon TDI with same LR sensor malfunction codes .. great timing on this video, I suspect broken tone/magnetic ring.. good video

Good investigation. Very informative video

Dave thanx a lot bro you helped me out.. I was hooking the other black wire from the switch to the white wire coming out of the wall.. and got. BOOM!!💥💥but no fire🙏🏾.. now I can go set up my lights thanx again Dave🙏🏾