I was trying to use plasticity property 'concrete smeared cracking' in abaqus for explicit analysis. The error says "This keyword is not available in ABAQUS/Explicit." What may be the reason???
Good Morning Sir, I have a query about non absorbing boundary condition for Dam- Reservoir- Foundation Interaction... how to create Lysmer - Kuhlemeyer’s viscous boundary for foundation in Abaqus software for foundation? Please help me out...
Can you explain further in 10:53 you said that instability was caused by increasing plastic strain while yield stress decreased, how does that make sense? So what are the correct way to define plastic hardening phase?
"Abaqus/CAE kernel exited with an error, how to resolve", this message shows after installation when I open Abaqus 2023 first time in my Windows 11 Laptop
Hi Munirul, in your model, double click 'step', in the popup select 'Incrementation' tab, then for 'type' select 'automatic'. Finally, run the simulation again.
hii.. i have problem with my model.. the error message say that " the eigenvalue cannot be found. due to instabilities in the base state".. so which part shud i change?
Hi there, by any chance do you know to resolve the error "ABAQUS/standard rank 0 encountered a SEGMENTATION FAULT" ? My job is aborting and this seems to be the only discernible fault.
@@mailcharitha I'm not familiar with VUMAT but I imagine it is similar enough to UMAT, which is what I've used. There will be some sort of error in your VUMAT. Make sure that you have defined, initialised and appropriately used all of your terms. Also, make sure that each line of your VUMAT is succinctly short. I think that if any line is too long, the rest of it after a particular cut-off point will not be recognised.
Hey hai im getting this error msg over when i analyse the job, "OdbError: The .lck file for the output database C:/temp/Job-1.odb indicates that the Analysis Input File Processor is currently modifying the database. The database cannot be opened at this time. Analysis Input File Processor exited with an error." kindly help to get over it.
Hi, it means that the job is still running. You have to terminate it to run again. It can happen that the job is complete but the '.temp' file is not deleted as expected (This gives Abaqus the idea that the job is still running). You can try deleting the 'temp' file for the Job-1 and check if it solves the issue.
Hi, it means that the job is still running. You have to terminate it to run again. It can happen that the job is complete but the '.temp' file is not deleted as expected (This gives Abaqus the idea that the job is still running). You can try deleting the 'temp' file for the Job-1 and check if it solves the issue.
great video thanks
I was trying to use plasticity property 'concrete smeared cracking' in abaqus for explicit analysis. The error says
"This keyword is not available in ABAQUS/Explicit."
What may be the reason???
Okay but what to do after finding the error node or elements in the results, to converge the problem should they be removed/ replaced???
Good Morning Sir,
I have a query about non absorbing boundary condition for Dam- Reservoir- Foundation Interaction...
how to create Lysmer - Kuhlemeyer’s viscous boundary for foundation in Abaqus software for foundation?
Please help me out...
Can you explain further in 10:53 you said that instability was caused by increasing plastic strain while yield stress decreased, how does that make sense? So what are the correct way to define plastic hardening phase?
Why do I get this error
"the .inp or .sim extension has been removed from the job identifier"
Are you considering rigid boday roation in this setup?
"Abaqus/CAE kernel exited with an error, how to resolve", this message shows after installation when I open Abaqus 2023 first time in my Windows 11 Laptop
did u find a fix for it?
I am having this error message for the vertical axial load on the beam, "fixed time increment is too large"
what will i do? please help
Hi Munirul, in your model, double click 'step', in the popup select 'Incrementation' tab, then for 'type' select 'automatic'. Finally, run the simulation again.
Monsieur est ce que je peux vous envoyez mon fichier abaqus, j'ai pas pu trouver le problème, merci d'avance.
Hello sir in my abaqus 2020 there is no CFD. How to anable it because i have project of flow analysis.
hii.. i have problem with my model.. the error message say that " the eigenvalue cannot be found. due to instabilities in the base state".. so which part shud i change?
Any solutions to "Keyword cards for step dependent input must appear after the first *step card."?
It sounds misplaced keyword. Find ‘*step’ in the input file and check if your keyword is placed in a line somewhere after that
hello can you plz tell me I am facing error as excessive incremental elements rotation
where I can findt that file once the error appear?
"selected region must be continuous" any help????????????????
Sir, can I send you my abaqus file, I couldn't find the problem, thanks in advance.
I put 15 but the problm after 15U return
Hi there, by any chance do you know to resolve the error "ABAQUS/standard rank 0 encountered a SEGMENTATION FAULT" ? My job is aborting and this seems to be the only discernible fault.
did you find a solution for this? I get the same issue
@@mailcharitha Are you using subroutines?
@@joshuarees3976 Yes, I am using a VUMAT with Bilinear damage.
@@mailcharitha I'm not familiar with VUMAT but I imagine it is similar enough to UMAT, which is what I've used. There will be some sort of error in your VUMAT. Make sure that you have defined, initialised and appropriately used all of your terms. Also, make sure that each line of your VUMAT is succinctly short. I think that if any line is too long, the rest of it after a particular cut-off point will not be recognised.
Hey hai
im getting this error msg over when i analyse the job, "OdbError: The .lck file for the output database C:/temp/Job-1.odb indicates that the Analysis Input File Processor is currently modifying the database. The database cannot be opened at this time.
Analysis Input File Processor exited with an error." kindly help to get over it.
Hi, it means that the job is still running. You have to terminate it to run again. It can happen that the job is complete but the '.temp' file is not deleted as expected (This gives Abaqus the idea that the job is still running). You can try deleting the 'temp' file for the Job-1 and check if it solves the issue.
Hi, it means that the job is still running. You have to terminate it to run again. It can happen that the job is complete but the '.temp' file is not deleted as expected (This gives Abaqus the idea that the job is still running). You can try deleting the 'temp' file for the Job-1 and check if it solves the issue.
Thanks for the kind help will run the job again after terminate and inform u..
in keyword *CONFLICTS, file "TRY1.inp", line 36561: The keyword is misplaced. It can be suboption for the following keyword(s)/level(s):