I hope you used a torque wrench and some Loctite on those bolts. I haven't looked at the Mitsubishi workshop manual, but typically Loctite is used on any bolts which are exposed to extreme vibration or stressful flex conditions (which a wheel bearing will typically endure). The last thing you want is those 4x wheel bearing bolts you installed slowly backing themselves out and becoming loose especially if you just 'hand tightened' the bolts and guessed the torque for them 😋 The anti-seize copper grease isn't only to prevent the rotor from fusing. It will help prevent more rust from building up and it's always a good idea to coat the mating surfaces with it. You were also supposed to use the brake cleaner on the rotor friction surface (back an front) to ensure the pads are not contaminated with grease or WD-40. Wiping the surfaces with a paper towel and brake cleaner is the best method to ensure the rotor surfaces are clean for the pads. In your video you just sprayed the rusted area where the wheel hub make contact where you would typically put anti-seize grease 🙂
I am at 300k km now when I changed it. But I been hearing the droning sound from the rear wheel bearing since ard 280k . Front wheel bearings are still silent like it was in Day 1.
Thanks for your kind words. I really appreciate it. I actually did a video on gearbox oil and filter for this car model about 4 years back. Not the best audio but you will get the idea on what needs to be done th-cam.com/video/05B94tafIHc/w-d-xo.html
I hope you used a torque wrench and some Loctite on those bolts. I haven't looked at the Mitsubishi workshop manual, but typically Loctite is used on any bolts which are exposed to extreme vibration or stressful flex conditions (which a wheel bearing will typically endure). The last thing you want is those 4x wheel bearing bolts you installed slowly backing themselves out and becoming loose especially if you just 'hand tightened' the bolts and guessed the torque for them 😋
The anti-seize copper grease isn't only to prevent the rotor from fusing. It will help prevent more rust from building up and it's always a good idea to coat the mating surfaces with it. You were also supposed to use the brake cleaner on the rotor friction surface (back an front) to ensure the pads are not contaminated with grease or WD-40. Wiping the surfaces with a paper towel and brake cleaner is the best method to ensure the rotor surfaces are clean for the pads. In your video you just sprayed the rusted area where the wheel hub make contact where you would typically put anti-seize grease 🙂
Nice tip broo, I just replaced my bearing last month, I wish I had seen this sooner
Bro thank yoou for the toturial
You are most welcomed. More videos on this car as well in my channel, don't forget to check them out.
@@TCsAnythingGoes my car pulled a little bit to the left , i already done my aligntment .is it caused of bearing ?
Thank you boss
mine sounds exactly like that
Is it okay for the boss to use bearing brand Gaido x series??
Where's the footage of bearing removal thooooo
😂 click bait he just wanted to show off his wheels
Hey man , between GSP and Gaido for rear bearing , which one you recommend ?
Bro, the wheel bearing no need to pump out? Tqvm
for the front, yes. But for the rear, its an entire set.
Superb!
What's the mileage when you encountered this problem? Is the front bearing still good?
I am at 300k km now when I changed it. But I been hearing the droning sound from the rear wheel bearing since ard 280k . Front wheel bearings are still silent like it was in Day 1.
always watch ur videos and thanks for this.
hope u do a video on gearbox oil and filter also.
Thanks for your kind words. I really appreciate it. I actually did a video on gearbox oil and filter for this car model about 4 years back. Not the best audio but you will get the idea on what needs to be done
th-cam.com/video/05B94tafIHc/w-d-xo.html
@@TCsAnythingGoes appreciate the reply TC! Have a good week ahead. I'll check out the video! Keep on keeping on bro.
What's the torque for the 4 bolts?
71Nm + - 7Nm. Even hand tighten is enough since its such a low number.