Good video , I wish someone would go into the tuning aspects of installing an after market exhaust , fuel commanders, reprogramming ECUs and other options what’s practical and what’s not , but none the less informative video
There are not many of such videos on YT. I know one but it is in Polish language only. The mods were made to MT07 not only for the estetic purposes but also to encrease the performance (exhaust, air-box, ECU tuning, brakes etc.) Maybe I'll suggest the authors of the video to translate it info English. Or, at least to do the subtitles.
"Yes, we can" as soon as I get my moto back from the service. I also need to cut the welding that holds the dbkiller in place (it was probably the Euro4 requirement the producer had to follow).
No, I don't. Actually, this SC Project resembles the original exhaust system (shape and size) so perhaps the center stand would fit ... Maybe I could try to measure it. But it would not be very precise.
@@moyx1999 Yesterday I was trying to measure the big can/box of the muffler under the engine. I was quite difficult because the box is more or less square but it is not parallel to the ground - it is a little bit lower under the engine and goes up near the rear tire. So this was just very rough assessment than measurement: 1. The distance between middle of the bracket screw and the bottom of the muffler can - measured vertically down - was 8-9cm. 2. The max distance measured from the same point - down to the lowest part of the muffler box (the part that is under the engine, the point closest to the ground) was 18-19 cm 3. The width of the box: 20cm. 4. The max distance between the middle of the bracket screw measured horizontally (direction to the rear tire) and the end point of the box was: 8-10cm. 5. The end pipe sticks out of muffler more ir less in the same place. The distance between the end pipe and chassis: min 2, max 3cm. I do not think the above information would be enough to make a decision. I would advise to find and go to a shop that has both things on stock: the central stand and the exaust. Or, at least drop an email to SC Project for exact size of its product.
@@tatandvlog8192 Thank you for the effort 😊👍. I know that with Akrapovic is possible to fit the center stand, but I like SC Project more. If I can't get SC to go with the center stand then I will go for the Akrapovic. Thank you again 👍
I decided to not to remove it for a while. The db killer sits in the main pipe very tight and I am afraid of damaging it while cutting the welding. Secondly I had an accident and my XSR needs some repairs. I also need some "repairs".
@@tatandvlog8192 oh...sorry to hear that bro. Anyway, I kinda glanced somewhere that your going to post a follow up video without the db killer. Be waiting for that. Ride safe and get well soon. 💪👍
![รวมมิตร ภาพนี้ก็ฮาเหมือนกันนะเนี้ย #4 SS2 [ พากย์นรก MEME.EXE ] | easy boy](http://i.ytimg.com/vi/kl86m9gnLt8/mqdefault.jpg)
![[TH] VALORANT Champions Seoul - Semi-Final - SEN vs TH](http://i.ytimg.com/vi/IewhVY9cAmQ/mqdefault.jpg)
też musze wymieć rury... brzmi to przepięknie, ten właśnie niski pomruk
Sounds great! thanks for the helpful video
very nice sound, thumbs up.
greets from a German Motovlogger
Thx for your comment.
Nice Work you have done by replacing a portable Exhaust for safe keeping the Pillion's seating
Good video , I wish someone would go into the tuning aspects of installing an after market exhaust , fuel commanders, reprogramming ECUs and other options what’s practical and what’s not , but none the less informative video
There are not many of such videos on YT. I know one but it is in Polish language only. The mods were made to MT07 not only for the estetic purposes but also to encrease the performance (exhaust, air-box, ECU tuning, brakes etc.) Maybe I'll suggest the authors of the video to translate it info English. Or, at least to do the subtitles.
Looks good, sounds good.
Love it
Can we see the video comparing the sound with and without the db-killer?!
"Yes, we can" as soon as I get my moto back from the service. I also need to cut the welding that holds the dbkiller in place (it was probably the Euro4 requirement the producer had to follow).
please tell me what is the exhaust torque N~M
The 4 big nuts holdig the pipes to cylinders: 20 Nm. O2 sesnsor: 25Nm. Big screws holding the main can: 20 Nm. The rest: 10Nm.
How can i get the db killer out ?
I do not know yet. I had an accident in May and my bike is still broken. Fortunately my leg is better...
@@tatandvlog8192 ohh ok. Speedy recovery brother
.........Hello, ...."To be continued?"......😂✌👌
Well... I am busy, it was snowing again last week and I do not have a time to do it. But thanks for reminding me anyway.
that SC sounds nice and all, but what you really want is a kelpi shorty. you're welcome
Do you know if you can have the center stand fitted with this exhaust?
No, I don't. Actually, this SC Project resembles the original exhaust system (shape and size) so perhaps the center stand would fit ... Maybe I could try to measure it. But it would not be very precise.
@@tatandvlog8192 Thank you for your time :)
@@moyx1999 Yesterday I was trying to measure the big can/box of the muffler under the engine. I was quite difficult because the box is more or less square but it is not parallel to the ground - it is a little bit lower under the engine and goes up near the rear tire. So this was just very rough assessment than measurement:
1. The distance between middle of the bracket screw and the bottom of the muffler can - measured vertically down - was 8-9cm.
2. The max distance measured from the same point - down to the lowest part of the muffler box (the part that is under the engine, the point closest to the ground) was 18-19 cm
3. The width of the box: 20cm.
4. The max distance between the middle of the bracket screw measured horizontally (direction to the rear tire) and the end point of the box was: 8-10cm.
5. The end pipe sticks out of muffler more ir less in the same place. The distance between the end pipe and chassis: min 2, max 3cm.
I do not think the above information would be enough to make a decision. I would advise to find and go to a shop that has both things on stock: the central stand and the exaust. Or, at least drop an email to SC Project for exact size of its product.
@@tatandvlog8192 Thank you for the effort 😊👍. I know that with Akrapovic is possible to fit the center stand, but I like SC Project more. If I can't get SC to go with the center stand then I will go for the Akrapovic. Thank you again 👍
Is this the Euro4 exhaust with catalyst?
Exactly.
It's fully legal. It has the euro4 certificate.
Should have removed the db killer though
I decided to not to remove it for a while. The db killer sits in the main pipe very tight and I am afraid of damaging it while cutting the welding. Secondly I had an accident and my XSR needs some repairs. I also need some "repairs".
@@tatandvlog8192 oh...sorry to hear that bro. Anyway, I kinda glanced somewhere that your going to post a follow up video without the db killer. Be waiting for that. Ride safe and get well soon. 💪👍