วีดีโอ

Oj, już nie pamiętam. Dawno było. Ale chyba dobrze. Nie mam porównania z GN. W 2015 przesiadłem się na XSR700.

@@tatandvlog8192 ok. Dzięki za szybką odpowiedź.

The 4 big nuts holdig the pipes to cylinders: 20 Nm. O2 sesnsor: 25Nm. Big screws holding the main can: 20 Nm. The rest: 10Nm.

I do not know yet. I had an accident in May and my bike is still broken. Fortunately my leg is better...

@@tatandvlog8192 ohh ok. Speedy recovery brother

I decided to not to remove it for a while. The db killer sits in the main pipe very tight and I am afraid of damaging it while cutting the welding. Secondly I had an accident and my XSR needs some repairs. I also need some "repairs".

@@tatandvlog8192 oh...sorry to hear that bro. Anyway, I kinda glanced somewhere that your going to post a follow up video without the db killer. Be waiting for that. Ride safe and get well soon. 💪👍

Well... I am busy, it was snowing again last week and I do not have a time to do it. But thanks for reminding me anyway.

"Yes, we can" as soon as I get my moto back from the service. I also need to cut the welding that holds the dbkiller in place (it was probably the Euro4 requirement the producer had to follow).

No, I don't. Actually, this SC Project resembles the original exhaust system (shape and size) so perhaps the center stand would fit ... Maybe I could try to measure it. But it would not be very precise.

@@tatandvlog8192 Thank you for your time :)

@@moyx1999 Yesterday I was trying to measure the big can/box of the muffler under the engine. I was quite difficult because the box is more or less square but it is not parallel to the ground - it is a little bit lower under the engine and goes up near the rear tire. So this was just very rough assessment than measurement: 1. The distance between middle of the bracket screw and the bottom of the muffler can - measured vertically down - was 8-9cm. 2. The max distance measured from the same point - down to the lowest part of the muffler box (the part that is under the engine, the point closest to the ground) was 18-19 cm 3. The width of the box: 20cm. 4. The max distance between the middle of the bracket screw measured horizontally (direction to the rear tire) and the end point of the box was: 8-10cm. 5. The end pipe sticks out of muffler more ir less in the same place. The distance between the end pipe and chassis: min 2, max 3cm. I do not think the above information would be enough to make a decision. I would advise to find and go to a shop that has both things on stock: the central stand and the exaust. Or, at least drop an email to SC Project for exact size of its product.

@@tatandvlog8192 Thank you for the effort 😊👍. I know that with Akrapovic is possible to fit the center stand, but I like SC Project more. If I can't get SC to go with the center stand then I will go for the Akrapovic. Thank you again 👍

There are not many of such videos on YT. I know one but it is in Polish language only. The mods were made to MT07 not only for the estetic purposes but also to encrease the performance (exhaust, air-box, ECU tuning, brakes etc.) Maybe I'll suggest the authors of the video to translate it info English. Or, at least to do the subtitles.

Exactly.

It's fully legal. It has the euro4 certificate.

Thx for your comment.

Niestety, sprzedałem tux-a w 2018. O jakie informacje chodzi?

Chodzi mi o tłumik, kupował to Pan osobiście na allegro? Ja mam jakiś głośny zamiennik i muszę coś znalesc

Kupiłem razem z moto.