1999-2004 Ford F250 F350 Loose Axle Shaft, Broken Locking Hub, Bad Bearing, Bad Outer Shaft
ฝัง
- เผยแพร่เมื่อ 9 ม.ค. 2022
- Link To Product On Our Website.
venturestruckparts.com/produc...
1999 200 2001 2002 2003 2004 Ford Super Duty F250 And F350
2000 2001 2002 2003 2004 2005Ford Excursion
Common issues or problems with front axle.
Bad needle bearing, vacuum seal, or outer stub shaft. Broken Locking hub or loose axle shaft.
Needle Bearing Replacement Video.
• 1998-2004 Ford F250 F3...
Ventures Truck Parts
(801)621-0091
www.venturestruckparts.com - ยานยนต์และพาหนะ
Thank you for this video. This just stated happening to my son F350. We did not take it apart yet.
Great tank god bless you
great video
Thank you
I replaced my hubs with OEM have any luck with aftermarket hubs
I also bought a tool to set the dust seal
Now I understand why that needle bearing is quite small, it only supports the drive shaft/axle. The actual wheel and weight of the truck is supported by the larger bearing of the hub. going to pull the locking hub and see how the drive shaft looks. Removing the entire hub is quite a pain.
Great informative video! You state this is a common problem when these trucks are not maintained properly. But what is the proper maintenance? I have a 2004 F250. The maintenance schedule in my owner's guide instructs to "Lubricate 4x4 hub needle bearings" every 60k miles, but it does not specify whether it is referring to the outer bearings inside the locking hub or the inner bearings that ride on the axle shaft that you discuss in this video. Does it mean both? Should the entire hub assembly be completely removed every 60k to regrease these inner bearings?
Same Question... How do we keep them lubed when they are Sealed ??
You would need to remove the hub assy, Grease the bearing and then re assemble.
My outer tie rod is grinding on the actual rim ????
If the internal bearing you stated that holds the weight of the vehicle is starting to bind can I tear it down and change that bearing or do I need to replace the entire hub?
You will need to replace the Hub Assy. as a unit.
@@VenturesTruckParts thanks for the response.will do
Mine looks like that but just started only feel it in 4wd probably had 1/8 to a 1/4” of play is that the bad part?
The design of this axle is part time 4 wheel drive. Most likely you will not feel it unless 4WD is on because your shafts should not be spinning in 2WD
U should have a close up on the shaft to see what tapered edge is no good.
Question. Can that make the tire wobble?
No. If your tire is wobbling your wheel bearings or ball joints are bad.
How do you lube that? Are there grease zirks?
The only way to lube the bearing is to remove the hub assy, grease the bearing and re assemble.
Great vid. At the start there is a lot of grease/oil deposit on the lower ball joint area. Is this normal build up or seepage from the axle? I have the same build up and trying to determine the cause. Thanks
If you have oil seeping out of your axle tube down on the balljoint nut the most common problem is the inner oil seal is leaking. Here is a link to new ones.
www.ebay.com/itm/361489100242
Also you will want to check your differential fluid level so you do not run out of oil.
Does a new hub assembly have the bearing in it when purchased?
Yes, the wheel hubs we sell have a new needle bearing in them.
@@VenturesTruckParts y'all sell the half shaft as well?
@@vincentwelshman8435 Yes we have anything you need for that front axle. Good used or new OEM Dana Spicer
I think my shaft is bent of something. I took the locking hub off to replace it and now the bastard wont go back on. When I spin the wheel I can see that the shaft isnt center. Still tryin to get it back on
It’s probably too late for this, but if you stick the crowbar behind the wheel on the knuckle and lift the shaft it’ll align and you can put the lock hub in, obviously this should only be a temporary fix as you need to replace the seal or wheel hub, it will straighten out once you fix it
Do you do repairs for the public?
Unfortunately we do not. We only sell the parts.
When I was driving every little bump made my trunk shake until I completely stopped
Is this the cause
I was is 2w drive too
@@scorpio4992did u figure it out?
@@BenPat88 no sir haven't tried to fix it it's not mine it's a family members
Where is the link
See the video description.