Kohler Starter Click Click Repair
ฝัง
- เผยแพร่เมื่อ 6 ก.ย. 2024
- amzn.to/2Z18vBh Replacement Starter
amzn.to/3cnwfDa Non Aerosol Spray Can
amzn.to/3coWjxS Jumper cables for testing
amzn.to/2yI95ZJ Hanson Socket Organizer Tray
Help support Doublewide6 Repairs LLC by sponsoring his Patreon Account
/ doublewide6
In this video I take a look at a starter on a Kohler engine that would not turn over, but made a clicking noise.
Doublewide6 Repairs LLC has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 Repairs LLC and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 Repairs LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’ Repairs LLC's videos. Use this information at your own risk. Doublewide6 Repairs LLC recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6 Repairs LLC, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6 Repairs LLC.
amzn.to/2Z18vBh Replacement Starter
amzn.to/3cnwfDa Non Aerosol Spray Can
amzn.to/3coWjxS Jumper cables for testing
amzn.to/2yI95ZJ Hanson Socket Organizer Tray
Nice VId, those starters are $250. I bought a replacement from who knows where for $68 to my door. Living off grid with a Kohler 20KW , i always need a backup. I had to tap on the starter to fire up the house for weeks until one morning I woke up to my house shut down and no way to start the generator. Put the new one in in the cold dark with a headlamp in my pajamas. No big deal, but I appreciate you making this video showing the inside of this thing. Keep up the good work sir.
Dude. You just saved me $70 bucks! My brush assembly was packed with oil/fine grass particle mixture. Cleaned her up and she spins great now!
The dirt is carbon dust, it is conductive. When you cleaned the armature, make sure to clean the spaces between the copper contacts, that will definitely cause slow rotation.
great video, short but sweet tutorial on starter operation and repair, dirt is always the culprit. Thanks
You bet
Two things. You did not disassemble the Solenoid. It does come apart, similar to a GM car one. There are contacts under the post to be cleaned and/or rotated 180 degrees.
Second, that Bendix style worm gear drive in the starter body, needs cleaned and lubricated. Good video, thanx for sharing.
Not trying to be critical (very helpful video!), just worried about your safety. When bench testing I like to leave the positive cable connected, and connect the ground cable temporarily to test. That way you don't get all that sparking, right next to a can of acetone mixture. 🙂 Even better yet, a remote starter switch (inexpensive) is safer yet.
Thank you again, very helpful disassembly video. I have the same exact starter and you just saved me some guess work!
Thanks for the excellent breakdown and presentation 👍.
It doesn't look like you checked the solenoid at all, and even bypassed it when testing at the end. If you had an external solenoid set up to work just like your booster cables that would work, but as-is that starter could still be clicking all day. I thought you were actually going to open up and repair the solenoid part, not just blow the worn brush dust out of the motor.
It is nice to see something repaired.
It's Bruce approved!
You see it everyday in your garage. Let me know if you are interested in teaming up on a video somehow?
Those brushes can be a bear to re- install. There are little holes you can put paper clip size wire into that retract the brushes away from the armature
Thanks for this tip. Have messed around for a good 10 minutes trying to get the back in.
Thanks for the great video my GT 5000 would click a few times then it would turn over and start I replaced the undersize battery and I think I can get buy till warmer weather then I'll take the starter off and clean it up etc. thanks again keep up the good work.
If he had crossed his eyes, tugged his left ear and shook his right foot all about, he’d have been golden😀
I got it to start one time for me, but I had to stomp my foot twice.
My starter is clicking but not turning. When do you clean it versus buying a new one ? A new starter.
Would of been nice to see how it was running before you cleaned it up. And then reinstall after cleaning to prove it's not only functioning better but capable of turning over the engine like it should.
I should have shown it running on the bench. I ran but very slowly. I couldn't put back on tractor because it was a Gravely zero turn that was in a very very tight spot to remove. With hoses, wires, gas tank, and oil cooler is took 45 min. to remove.
Is there anywhere you can buy only the brushes for this starter? The brushes on my starter are gonne.
You are the man Bob. Thanks for sharing. I have never been in a starter before so I did learn a few things. Stay Safe. Stay Healthy. God Bless!
It is always fun to tear into something that you don't have to worry about destroying.
17:29 Good job. My only comment is that it seems like it takes a long time for the motor to wind up. With no load, seems like max rpm should be almost instantaneous.
Yeah. My thoughts exactly.
Yes I looked at it I agree. I will have to try it on an engine to see. What do I need to do to try and fix it?
@@doublewide6 I have a feeling that the old motor's field windings are partially shorted or the brushes are not properly conducting. A resistance comparison between the old motor and the new would confirm.
In any case, a good call to replace! Regards.
...... I concur, I expected it to jump off the bench if all the stator windings were intact.
Not economically viable I suppose to map out each field and measure ohms.
You tightened the bolts while the starter was on its side causing misalignment. Tighten them with the starter standing straight up and gradually tighten both together.
Great vid: never seen inside a starter .
Why use a penitrating oil to lube the plain bearings? Wouldn't a regular oil last longer? I do a lot of starters and electrical motors, like ceiling fans and bath room vent fans and just put in a light weight oil to lube the bearings. Just curious. I like the video, Good Job!
This is how he puts on he's name he's still a child 😂
Hello there! The starter motor on my grasshopper 223 takes few turns before it turns the engine. What do you think it is???
solinoid has copper cotacts which can be cleanedup. use too do it all the time on gm cars. great video. use too clean older gh ones all the time just brush them clean n back together
Thanks for the tip! Inside the solinoid or the ones on the outside?
@@doublewide6 Inside. be carefull takiking apart copper wire is easy too break. take care.
Great video on starter repair and anatomy. On some of my old car starters the bushings in the ends would get bad and the armature would rub on the magnets some and would be to much drag to turn over then engine much. But maybe you got this one fixed up to use in a pinch anyway. Thanks for sharing.
It’s always a good idea to get a little basic information about the thing your about to dive into before you start. Carbon brushes on any armature electric motor never need to be attacked with a file, also they are easy to reposition in the motor if you pull them out slightly then use the spring to hold them out until the assembly is refitted.
Always great to try new things but get a little insight first. Just sayin!!!
good vid bob ... now if i can only get my zero turn back going checked the valves now it could be the starter bummer .. mine has the starter by it self .. kohler double v 23 hp pro .. †
What is wrong with your tractor?
@@doublewide6 ... been having probs trying to start it .. set the valves hope i did it right .. tried the solenoid seems ok so i hope it's the starter now and nothing wrong with engine the starter made a noise now and started to smoke a little bit now soooo .........
@@redskool8498 replace the starter. Charge that battery, if you still have hard starting you may have a broken compression release and have to replace the cam. Pretty common on Briggs.
@@doublewide6 ... not a briggs bob .. kohler double v 23 hp pro .. also a new battery it checks out good ..
Good video.
Happy Motoring.
Great job, great video!
Thank you!
you know when you pulled off the brushes, if you used a socket the same size you could have pushed it right on🖖 You should stretch the Bendix spring out a bit mine has a ford solenoid I hate that and will get rid of it under the battery plate with 1"+ hard to reach bolts and no bracket to the steering wheel so it moves enough to assist in wearing out steering pinion system with the bolt under the engine plate you have to remove the PTO THE ENGINEER SHOULD HAVE TO WALK A BED OF HOT COALS🤪🤯✌
Eveytime I see a motor opened up like this one and I see all that copper I think to myself... damn we have mined an enormous amount of copper from the Earth!
And they want a LOT more for the EVs they are wanting to force on us.
Nice job DW6! 👍👍
Thanks 👍
Thank you
Should of tested it first to see if starter engages.
where do you get acitone from?
Acetone
no like