Mine went out a few days ago. Engine was banging. I was scared. I thought it was going to explode it was shaking so hard. Definitely at idle. Good video.
You are right,my JZX90 1JZ GTE non VVTI won't start. Crank sensor checking all dry but when the cam sensor checked .. got an oil and water contamination plus the socket bridle af. Clean it change the socket everything perfectly start like normal. Just reminds guys if the cam sensor broke or dirty,you might got the crank on stater and the injection sprayed gas on combustion but no spark,result the strong gasoline smelled.
Please can a camshaft position sensor cause no injector pulse in Mitsubishi Hilux? My scanner is capturing RPM to be 113 RPM during cranking and nothing more. Please what do I need to do? Is that reading okay?
I got the code for my camshaft p sensor but were my belt is there is so much noise especially when I turn on the ac it’s shaking & having a hard time staying on at the stop sign
Hi mate I have issue with crankshaft sensor, car is missfiring and went in limp mode, and no code for the crankshaft sensor On my scan tool no reading from the sensor zero reading Honda insight
Exactly! Same problem here, why don't nobody who makes these videos knows the answer to this? I makes no sense to change them then the still has the the same issue, my car barely goes 45mph but if I try to erase the code the reader says failure to clear but finally the check engine light goes off then the car drives normal until the light pops back up 😡 I hate sensors!
@@shondablack6835 yeah mine I got had all the same color wires on the pig tail to the sensor from car so it read pending on reader cuz was crossed did the none hot wires cuz would short if so worked fine just see if it’s wired wrong
Have an 05 Lexus GX470. Had a TB service done 2000 miles ago. One day truck would not start. Recently jumped started it and pulled P0340 and P0345. Go back to the shop as they are accountable?
Is it possible that my car stalls sometimes without any fault sign on the dashboard and error code in memory due to faulty camshaft position sensor? Thanks for useful video!
Engine saking, rough idle, poor fuel mileage........sounds like a thumby cammed v8 on a good day lol. Great info but can't quite use these tips in my case😅
My engine has been making a whurling noise, with the idle flucating off and on at low rpms. I replaced throttle body, Cleaned map sensor, flushed engined could this be the camshaft sensor also?
Hello love your help and thank you. Question I got 2017 dodge grand caravan 3.6 with number 6 miss firing. Everything checks out. Intake, plugs, coil and injector also vacuum. Still has miss fire on idle. What I notice is that injector pulse is around 1400-1600 while all the others are around 1700+. Any tips. Currently leading toward pcm.
03 acura mdx ,After changing water pump and timing belt. I removed the spark plugs and coil just to make it easy on turning the crank to DTC once everything was complete. Check light came on and got p0344. Am on 3rd day trying to figure this out. Can low oil cause this code ?
Love some help all !!! I’ve got the code and will replace Camshaft position sensor The No1 reason for code is exactly what I have Valve gasket leak ( major leak ) This video says it isn’t the sensor that fails its oil contamination from valve gasket leak! So it’s the oil that’s gone bad through the valve leaking. Need to change the oil. And the sensor. Or just the oil. Many thanks.
Diagnostics showed as car camshaft sensor throwing timing chain off. However I didn’t see the code myself, ordered new sensors and now car is jerking whilst accelerating. I did order an upper and normal one and not sure why it’s not working.. any help?
Hello brother my '07 check engine light came on and the scanner only shows cose P0016, still runs great but feels heavy when running, which one can it be the camshaft sensor or camshaft valve? Thanks bro
Need to understand how oil could pass thru camshaft position sensor for engine line M276 or M278?. Oil passing thru the flat tip of the sensor resulting in oil in the connector and pass thru the wire into ECU?.
I replaced my transmission and it says the cam ia out of sync. Had a shop mechanic come out with hos 10g snap on scanner and he said he dont know why that sensor says its out of sync.
I have a 2006 Ford mustang GT with a 4.6 that will not start and on top of that my check engine light does not come on so I don’t know what the issue is but I’m starting to suspect the cam sensors may be bad I’ve already replaced the crank shaft position sensor. Right now I’m not getting a signal to the power packs for the spark plugs.
My 2018 F150 5.0L throws a camshaft sensor code on bank 2 sensor 2 which is the exhaust sensor. What tool do I need to remove the connector? There is a white integrated clip in the connector that locks the connector in place but, once it is released it will not come off of the sensor and there isn't enough wiring to be able to get 2 hands on it. There must be a special tool to extract that connector.
Please explain valve cover leak causing camshaft sensors to be faulty. Getting low and high input codes for both banks on bmw 745li 02 after having a major valve cover leak. The connectors from wire harness don’t seem to be contaminated by oil but they sensors were soaked in oil with some on connector prongs.
My vehicle only have one camshaft sensor on my 2002 Chevy express 1500 5.7l. No engine light and code p0300. Have you ever seen this code with the sensor being bad?
04 Altima 2.5. My problem is someone or an animal cut/ chewed all three wires to the crank sensor. This is right againts the large wire loom down on the firewall. I can't splice wires there so can it be done elsewhere underhood ? Wires blk, wht, +red/ green stripe.
@Top5AutoRepairs I bought a 2004 chevy aveo has 40k mils on it , it has broken timing belt pully , I changed the the timing belt and water pump and timing pulley and tensioner , my timing marks are perfectly aligned. It would crank no start now . I can see I have spark from the coil pack and I have fuel also . I changed the crankshaft sensor and no luck . I think only 1 thing left the camshaft sensor.
ปีที่แล้ว +1
@Top5AutoRepairs when I went to buy the car I asked the owner he said the car just didn't have power and stopped moving while he was driving. So I immediately checked the timming belt and sure enough it was lose and the timming pulley was broken .
My honest mechanic said my timing chain is loose making a ticking sound. He recommended to have it replaced so wont damage cam position sensor, valves, piston. He said also it really time coz my truck has 280k odo n will last another 200k. Your validation is appreciated.
@@Top5AutoRepairs he quoted whole cloyes timing chain kit n while its open replace oil pump n water pump for $2400 about 15 hrs labor but reduce to 10 hrs. In return, i give fresh fruits avocados n oranges. Sweet deal !
sensor is 10-40$. about 100-200 if a garage changes it. All depends on location. some older vehicles are a 10 minute job, and mine is closer to an hour to change.
Can a cam shaft position sensor on a two thous and nine audi q seven go out if it's been sitting for 7 months? Just purchased one and I got camshaft and crankshaft sensor codes.. vehicle will start acceleration then it will lie wanna die/stall/jerk... will these issues go away if I change these sensors?
I bought new sensors on my Mercedes Benz 2012 replace them as I was getting the code P0346 after replacing that and drove the car for a short time without a problem then again, the rough starting comes back with the same code reading. I’m not sure if there is anything else I should check for.
Mine went out a few days ago. Engine was banging. I was scared. I thought it was going to explode it was shaking so hard. Definitely at idle. Good video.
You are right,my JZX90 1JZ GTE non VVTI won't start. Crank sensor checking all dry but when the cam sensor checked .. got an oil and water contamination plus the socket bridle af. Clean it change the socket everything perfectly start like normal. Just reminds guys if the cam sensor broke or dirty,you might got the crank on stater and the injection sprayed gas on combustion but no spark,result the strong gasoline smelled.
Please can a camshaft position sensor cause no injector pulse in Mitsubishi Hilux?
My scanner is capturing RPM to be 113 RPM during cranking and nothing more. Please what do I need to do? Is that reading okay?
I got the code for my camshaft p sensor but were my belt is there is so much noise especially when I turn on the ac it’s shaking & having a hard time staying on at the stop sign
👌🏽😎always great information.
Swig of beer every time he says camshaft position sensor
😂😂😂😂😂
Hi mate
I have issue with crankshaft sensor, car is missfiring and went in limp mode, and no code for the crankshaft sensor
On my scan tool no reading from the sensor zero reading
Honda insight
Can my Can shaft sensor gonna a bad but not shown on the computer? I have crank no start with fuel and spark
Yes it's possible
Hi I did all them bank 1 2 and crank then I stared it and drove won’t go past 2 thousand rpm and idk what now no engine light before and after
Exactly! Same problem here, why don't nobody who makes these videos knows the answer to this? I makes no sense to change them then the still has the the same issue, my car barely goes 45mph but if I try to erase the code the reader says failure to clear but finally the check engine light goes off then the car drives normal until the light pops back up 😡 I hate sensors!
@@shondablack6835 yeah mine I got had all the same color wires on the pig tail to the sensor from car so it read pending on reader cuz was crossed did the none hot wires
cuz would short if so worked fine just see if it’s wired wrong
Thank you!
Have an 05 Lexus GX470. Had a TB service done 2000 miles ago. One day truck would not start. Recently jumped started it and pulled P0340 and P0345. Go back to the shop as they are accountable?
I changed the camshaft position sensor on my 2014 Chevy Sonic, the engine light still stays on
Is it possible that my car stalls sometimes without any fault sign on the dashboard and error code in memory due to faulty camshaft position sensor?
Thanks for useful video!
What model car is it?
Why cranksonsor only last a week after change
How can I tell I replaced it two
three times every time I wipe the code it come right back on redid the timing
My dteq 2008 is viewing crankshaft and camshaft sensor on machine but it's starting well I ones removed the injector pump
Engine saking, rough idle, poor fuel mileage........sounds like a thumby cammed v8 on a good day lol. Great info but can't quite use these tips in my case😅
My a4 is accelerating poorly when I step on pedal ?
My engine has been making a whurling noise, with the idle flucating off and on at low rpms. I replaced throttle body, Cleaned map sensor, flushed engined could this be the camshaft sensor also?
Hello love your help and thank you. Question I got 2017 dodge grand caravan 3.6 with number 6 miss firing. Everything checks out. Intake, plugs, coil and injector also vacuum. Still has miss fire on idle. What I notice is that injector pulse is around 1400-1600 while all the others are around 1700+. Any tips. Currently leading toward pcm.
03 acura mdx ,After changing water pump and timing belt. I removed the spark plugs and coil just to make it easy on turning the crank to DTC once everything was complete. Check light came on and got p0344. Am on 3rd day trying to figure this out. Can low oil cause this code ?
Love some help all !!!
I’ve got the code and will replace Camshaft position sensor
The No1 reason for code is exactly what I have
Valve gasket leak ( major leak )
This video says it isn’t the sensor that fails its oil contamination from valve gasket leak! So it’s the oil that’s gone bad through the valve leaking. Need to change the oil. And the sensor. Or just the oil.
Many thanks.
Diagnostics showed as car camshaft sensor throwing timing chain off. However I didn’t see the code myself, ordered new sensors and now car is jerking whilst accelerating. I did order an upper and normal one and not sure why it’s not working.. any help?
Can a car start if that seal on gear is damaged
Thank you for your time sir
Need the location of the camshaft position sensor on 2013 Honda crv 4cylinder. Thanks
p0340 code on 2013 nissan pathfinder. How do i find out which sensor to replace ?
Hello brother my '07 check engine light came on and the scanner only shows cose P0016, still runs great but feels heavy when running, which one can it be the camshaft sensor or camshaft valve? Thanks bro
I always thought a 1997 F250 heavy duty 7.5 L big block has one camshaft
Need to understand how oil could pass thru camshaft position sensor for engine line M276 or M278?. Oil passing thru the flat tip of the sensor resulting in oil in the connector and pass thru the wire into ECU?.
I replaced my transmission and it says the cam ia out of sync. Had a shop mechanic come out with hos 10g snap on scanner and he said he dont know why that sensor says its out of sync.
My explorer 1999 SOHC after a few months non use there is hesitation, when i step on the gas
I have a 2006 Ford mustang GT with a 4.6 that will not start and on top of that my check engine light does not come on so I don’t know what the issue is but I’m starting to suspect the cam sensors may be bad I’ve already replaced the crank shaft position sensor. Right now I’m not getting a signal to the power packs for the spark plugs.
My 2018 F150 5.0L throws a camshaft sensor code on bank 2 sensor 2 which is the exhaust sensor. What tool do I need to remove the connector? There is a white integrated clip in the connector that locks the connector in place but, once it is released it will not come off of the sensor and there isn't enough wiring to be able to get 2 hands on it. There must be a special tool to extract that connector.
Cam vs crank ?
My Mitsubishi has cam sensor top Crank on bottom
Please explain valve cover leak causing camshaft sensors to be faulty. Getting low and high input codes for both banks on bmw 745li 02 after having a major valve cover leak. The connectors from wire harness don’t seem to be contaminated by oil but they sensors were soaked in oil with some on connector prongs.
Valve cover was replaced n codes came back both low n high inputs. Didn’t seem like oil got all the way to the ECM.
My vehicle only have one camshaft sensor on my 2002 Chevy express 1500 5.7l. No engine light and code p0300. Have you ever seen this code with the sensor being bad?
U ever find out what was giving u the p0300 code
You are best
Thanks bro ❤
04 Altima 2.5. My problem is someone or an animal cut/ chewed all three wires to the crank sensor. This is right againts the large wire loom down on the firewall. I can't splice wires there so can it be done elsewhere underhood ? Wires blk, wht, +red/ green stripe.
Can camshaft position cause crank no start ?
Yes it can
@Top5AutoRepairs I bought a 2004 chevy aveo has 40k mils on it , it has broken timing belt pully , I changed the the timing belt and water pump and timing pulley and tensioner , my timing marks are perfectly aligned.
It would crank no start now .
I can see I have spark from the coil pack and I have fuel also .
I changed the crankshaft sensor and no luck .
I think only 1 thing left the camshaft sensor.
@Top5AutoRepairs when I went to buy the car I asked the owner he said the car just didn't have power and stopped moving while he was driving.
So I immediately checked the timming belt and sure enough it was lose and the timming pulley was broken .
Check compression. If no compression valves are bent.
@Top5AutoRepairs thanks for your reply I will check asap .
bank 1 is 340 not 341
What about P0335
Thank you great information 🫡🤙🏾
how would it look using just a standard obd2 reader?
My honest mechanic said my timing chain is loose making a ticking sound. He recommended to have it replaced so wont damage cam position sensor, valves, piston. He said also it really time coz my truck has 280k odo n will last another 200k. Your validation is appreciated.
At 280k it's due for timing chain, tensioner, timing guide etc... replacement.
@@Top5AutoRepairs he quoted whole cloyes timing chain kit n while its open replace oil pump n water pump for $2400 about 15 hrs labor but reduce to 10 hrs. In return, i give fresh fruits avocados n oranges. Sweet deal !
Does anyone have a range of how much this will cost plus labor?
sensor is 10-40$. about 100-200 if a garage changes it. All depends on location. some older vehicles are a 10 minute job, and mine is closer to an hour to change.
you dat-viet??
.....
Can a cam shaft position sensor on a two thous and nine audi q seven go out if it's been sitting for 7 months? Just purchased one and I got camshaft and crankshaft sensor codes.. vehicle will start acceleration then it will lie wanna die/stall/jerk... will these issues go away if I change these sensors?
🙂👍
👍👍
I changed my camshaft sensors on my 2005 infinity now my ignition won’t turn could that be a problem why my ignition is locked?
I bought a new sensor for the bmw thinking my sensor is out. But the new one is magnetic strong like the oem one.
I bought new sensors on my Mercedes Benz 2012 replace them as I was getting the code P0346 after replacing that and drove the car for a short time without a problem then again, the rough starting comes back with the same code reading. I’m not sure if there is anything else I should check for.
5.7 Hemi
OK so my 2001 grand marquis has a V8 but only has 1 camshaft position sensor can you tell me where it is and procedure for replacement? Thx