Ford Fiesta Rear Hatch DIY Upgrade Boot Gas Springs Upgrade
ฝัง
- เผยแพร่เมื่อ 11 ม.ค. 2025
- With this simple spring kit you can convert your car boot into a Automatic Trunk. Takes 10 mins to install!
Description
Mold spring：TL Light Load
Color: Blue
Material: Alloy steel
Can be compressed to 52% of the total length
2:53, there is one hand pushing from the trunk.. OMG
Magic
And clearly no springs on the struts where they were supposedly fitted either
There's literally a man hiding in the boot 🤣🤣🤣
@ 2:53 can clearly see someone's hand pushing the boot lid open from inside🤣🤣
Came across this vid from a eBay seller using it as fitting instructions hahaa
Hey mate if you use a 3/4” tap washer and put it on before the spring, you won’t have the rattling issue or any noise.
The aim is to use the washer to keep hold the spring to the top end of the strut which is fixed to your boot
For the noise, how about fitting rubber grommets inside the springs, they'll also act as wipers for the struts.
2:52 so in the end he replaced the spring with a human hand. anyway thanks for the video for the warnings and cons involved
🤣
...probably was -1000°C that's why a handy hand was necessary....probably in the summer might even work a bit better
Spring Size. Out Dia(15mm ~ 20mm) * Inner Dia(9~10mm) * Length(35~40mm) OR HYUNDAI PART NO, 46395-39000 / washers(Rubber) Size. Out Dia(15mm ~ 20mm) * Inner Dia(9~10mm) From Seoul .^^.
Just fit a stronger gas strut and you can achieve the same without any fuss or additional components.
I've personally tried this method and can say it does not work!! Tried two different strength springs and both failed. Plus I don't have anyone in the boot to help push the boot up like the video host has. Ha ha
Good morning! Can you tell me the Ling about the springs? I have a fiesta mk6.
Vid actually starts 0:59
struggling to get the pivot bit off even with the rubber pliers and screwdriver
Did you manage to do it?
Thanks for your help
On ebay its listen for audi b7 estate. Will it fit the sedan?
where is the bump stops? You shouldn't have installed them all the way at the bottom but at the top
Where is spring on video opening??
How you determined the phisical aspect (dimensions) of the spring?
Don't bother, it doesn't work....
Should of just added slight foam to bottom side of spring to stop the horrible noise
What is the size of the light load spring?
Theres no spring on the strut either
Isn't it dangerous in underground parkings ?
Focus MK2 also be used?
yes, but I don't recomended it.
It's a shame it's because someone shows that he pushes the trunk with his hands sorry
exactly, just wanted to show why you sholud'n buy
What amazes me is this video is linked from the seller on eBay. Absolutely shocking scam.
3:01
Will this fit a mk7.5 fiesta ?
nope sorry
In the end the original struts are still on the car ! NO spring visible at 2.58, what a con !
@AJJ Jurgen probably need new struts and a mate in the boot to give it that extra push, like the guy in the video has.
Where can i get the springs
ebay, amazon, banggood
@@DrHannibal009 whats the spring called to type on ebay
@@DilwarHussain-fi7kfits called car trunk die spring mould
Link of product ?
www.ebay.com/itm/Compression-Die-Mould-Spring-Light-Load-TL-Blue-OD-16mm-22mm-Length-20mm-300mm/323959684495?hash=item4b6d807d8f:m:mb5vE2VPJLs19WKyHDm9AnA
Dove comprare le molle
Is this accurate?
Watch the full video, I don't recommend it..
These are a scam and as you can see one previous comments you can see someone pushing the boot open
Can you tell me the dimensions please?
It’s literally in the video
I didnt buy Any, because of the noise warning alone..
Haha total bollocks, unless the kit comes with the extra human to carry in the boot.... And then throw away the springs that are clearly not even fitted to the struts....