Thank you so much Jaco I had no one to teach me how to do a proper installation, now I just did managed to install a new Clutch kit, thank you once again, From Bloemfontein
Thanks for this video! Helped a lot. Was a bit worried as my clutch finally went after 340k km on my 1.6 XLT. Removal was easy. Installation of gearbox was terrible😂, no space to pick up box and little to no room where the diff sits next to the subframe. Never doing this in my driveway again.😂
We all say that. And next time round we do the same thing over. Glad I could help. Cheers. And many more good miles on the bantam. I should never have sold mine.
Very useful videos Jaco. I have already done some of the stuff shown and you're spot on 😜 Rocam is a tough little engine, quite remarkable in a number of ways. It also has a few irritating features 🤣 The concentric slave cylinder being one. A honda Ballade takes 10 minutes! That plastic thermostat housing. Actually the plastic parts in general but this is everywhere nowadays.
Thank you very much for this video I am doing my timing chain, cv joints axal completely new, my Bandam is making a rumbling noise when she starts up, so I hope by replacing the timing chain and components with the oil pump that that should be gone otherwise it's in the head, but I don't hope so. Any Ideas it sounds like the oil is priming for the first couple of seconds, MY 1600 Bantam has 300 000 km on the clock and.
@@katelynludwick speedometer sensor sits on the gearbox between the engine and firewall. It has plastic thread so be careful not to strip the thread when replacing it. (Ask me how I know)
Hi, Jaco.. This ws a great video especially for us who are learning about motor mechanics... I also wanted to ask you whats the issue when you pour brake fluid and it leaks from the gearbox after putting new thrust bearing in the ford ikon 1.6
hi Jaco, die prosedure vir 'n Ford Icon rocam is seker omtrent dieselfde, ek het volgende week een om te vervang, baie dankie, die video het baie gehelp. Groete Francois
On the concentric slave cylinder there is 2 ports. One is the hydraulic input. 2nd is the bleed valve. You will need 2 People. Depress the clutch Pedal. Open the bleed valve to release pressure. Close bleed valve. Release clutch pedal. In that order. Depress clutch pedal. Release bleed valve. Close bleed valve release clutch pedal. Repeat till all air is removed.
Basically, the same as breaks. there is a bleed valve on the clutch slave cylinder. get the laaitie to pump the clutch while you open and close the bleed valve. let me know if you do not get it right.
Привет, я тоже снимаю видео. У меня Форд Фокус 1 1.6 Duratec Rocam. Двигатель и коробка одинаковые как я понял, мне тоже предстоит снятие головы блока цилиндров, замена ГРМ... Спасибо за видео!
@@billiemor296 if I had to do it again, I would take off the bonnet ant take the engine and gearbox out as a unit and work on it outside of the vehicle.
Hi Jaco, great video,you are my mentor lol. I did an engine overhaul including changing clutch kit and the slave cylinder however I'm getting no clutch. I tried bleeding it however the clutch is not getting hard. Please help me buddy. Thank you
The reason for the engine overhaul was due to a blown head gasket however the bantam is still heating up pass the half mark. I removed the thermostat and installed a new water pump. The fan does come on and stays on for long and there after the head gauge rises pass half mark. What could be the problem? Thank you again.
The clutch is an absolute ball-ache to bleed. You need to be 2 people. Get one of the kids to depress the clutch pedal to build up pressure then you bleed off the air on the concentric slave cylinder. But note it takes for ever.and bleed it again a couple of days later.
@@JacoBadenhorst @Jaco Badenhorst I used anti freeze coolant and I have not changed the cap due to the cap seeming to be sealing fine, should I replace that? And I purchased a radiator flush today so I will try that as an option and I'll keep you posted.
@@JacoBadenhorst I managed to get some pressure on the clutch pedal however it won't select any gears and I did not remove the gear selector because I had removed the engine block and replaced everything there including the clutch. Any ideas?
Sorry about that. There is no place to film down there. It is basically the same as bleeding brakes. Get your son or someone to pump the pedal while you open and close the bleed port.
@@JacoBadenhorst No problem. I did learn that I'm never changing my own clutch haha. I did do my waterpump last weak. That was easy enough. I thought bleading my clutch may help since I'm stuggling to engage second. Sometimes it will go but usually doesn't.
@@gerritgeldenhuys2763 yes bleeding the clutch isn't to much work. Give it a go. Hopefully it's just air in the system and not the clutch plate itself.
On the concentric slave cylinder there is 2 ports. One is the hydraulic input. 2nd is the bleed valve. You will need 2people. Depress the clutch. Pedal. Open the bleed valve to release pressure. Close bleed valve. Release clutch pedal. Depress clutch pedal. Release bleed valve. Close bleed valve release clutch pedal. Repeat till all air is removed.
Thank you so much Jaco I had no one to teach me how to do a proper installation, now I just did managed to install a new Clutch kit, thank you once again, From Bloemfontein
@@obakengbotshelo2110 it's a pleasure. Glad the video helped.
Thank you Jaco. You a lifesaver. Appreciation from Pretoria
Super glad I could help!
Thanks for this video! Helped a lot. Was a bit worried as my clutch finally went after 340k km on my 1.6 XLT. Removal was easy. Installation of gearbox was terrible😂, no space to pick up box and little to no room where the diff sits next to the subframe. Never doing this in my driveway again.😂
We all say that. And next time round we do the same thing over. Glad I could help. Cheers. And many more good miles on the bantam. I should never have sold mine.
Baie dankie. Dit was deeglik gedoen en ek kon as leek presies volg wat jy gewys het. Dankie en sterkte
Thank you sir, this helped a lot
Very useful videos Jaco. I have already done some of the stuff shown and you're spot on 😜 Rocam is a tough little engine, quite remarkable in a number of ways. It also has a few irritating features 🤣
The concentric slave cylinder being one. A honda Ballade takes 10 minutes! That plastic thermostat housing. Actually the plastic parts in general but this is everywhere nowadays.
Thank you so much , i did it by looking at the video , , please can you make a video of a spare wheel holder installation please 🙏.
Fantasties Jaco dankie
Dankie Jaco waardeer die moeite🙏🔥
Thanks alot was able to do mine after watching this
Thank you very much for this video
I am doing my timing chain, cv joints axal completely new, my Bandam is making a rumbling noise when she starts up, so I hope by replacing the timing chain and components with the oil pump that that should be gone otherwise it's in the head, but I don't hope so. Any Ideas it sounds like the oil is priming for the first couple of seconds, MY 1600 Bantam has 300 000 km on the clock and.
You are very helpful thank you I'm looking for the speed sensor location on my bantam rocam
@@katelynludwick speedometer sensor sits on the gearbox between the engine and firewall. It has plastic thread so be careful not to strip the thread when replacing it. (Ask me how I know)
Hi, Jaco.. This ws a great video especially for us who are learning about motor mechanics... I also wanted to ask you whats the issue when you pour brake fluid and it leaks from the gearbox after putting new thrust bearing in the ford ikon 1.6
@@percym011 if brake fluid is leaking from the gearbox, the slave cylinder is probably shot. You will have split the engine and gearbox to check.
hi Jaco, die prosedure vir 'n Ford Icon rocam is seker omtrent dieselfde, ek het volgende week een om te vervang, baie dankie, die video het baie gehelp.
Groete
Francois
Ja dit sal selfde wees. Of baie baie naby.
Whoop whoop 1000 subs ek sê!!!
Great video #ClutchPlate #BakkieClutch #Clutch #Mechanic #HowTo #Bantam #Ford #FixClutch
Appreciate it!
How do I replace my selector seal on Ford bantam rocam 1300
Hi jaco i have a 2002 ford fiesta 1.6 8v rocam. Any idea if the 1.6 and 1.3 take the same flywheel plz hlp
You've got me on this one.not sure if it will be the same. Maybe phone FORD spares. Thy will be able to tell you.
hi Jaco. Do water pump change video on the Bantam rocam engin please. or give pointers. Many thanks
B. I will do a water pump video as soon as I need to replace the current one. Will look into it maybe just an overview?
Nice video once again
Thanx for the comment. I hope it helps you out.
hi Jaco,watse tipe olie gebruik jy vir die ratkas?
75W90 GL-5 synthetic high pressure gear oil.
How do you bleed the clutch ford rocam1.3
On the concentric slave cylinder there is 2 ports. One is the hydraulic input. 2nd is the bleed valve. You will need 2 People. Depress the clutch Pedal. Open the bleed valve to release pressure. Close bleed valve. Release clutch pedal. In that order. Depress clutch pedal. Release bleed valve. Close bleed valve release clutch pedal. Repeat till all air is removed.
Hi I wanted to know how do you bleed the clutch
Basically, the same as breaks. there is a bleed valve on the clutch slave cylinder. get the laaitie to pump the clutch while you open and close the bleed valve. let me know if you do not get it right.
@@JacoBadenhorstbeen doing that my clutch still not working
@@ofentsevincentmodise4726 this could take quite a while. Do you have all the fluids topped up?
i love your work ... I just Subz for more videos like this one
Awesome, thank you! Let me know if it was of any help?
Hi. Waar kry jy die adapter vir die pyp op die Slave cylinder
Die adapter het saam met die slave cylinder gekom in die verpakking. Vra vir jou plaaslikke spares shop. Hulle behoort dit te kan kry.
What oil used for gearbox?
75W90 synthetic high pressure gear oil
Привет, я тоже снимаю видео. У меня Форд Фокус 1 1.6 Duratec Rocam. Двигатель и коробка одинаковые как я понял, мне тоже предстоит снятие головы блока цилиндров, замена ГРМ... Спасибо за видео!
Vidoe bleeding clutch please
Jy sal n goeie onderwyser uitmaak
Baie dankie.
What oil did you put in gearbox
75W90 GL-5 synthetic high pressure gear oil.
Quick question when replace the whole engine should I remove the gear box and mount it outside
@@billiemor296 if I had to do it again, I would take off the bonnet ant take the engine and gearbox out as a unit and work on it outside of the vehicle.
Hi Jaco, great video,you are my mentor lol. I did an engine overhaul including changing clutch kit and the slave cylinder however I'm getting no clutch. I tried bleeding it however the clutch is not getting hard. Please help me buddy. Thank you
The reason for the engine overhaul was due to a blown head gasket however the bantam is still heating up pass the half mark. I removed the thermostat and installed a new water pump. The fan does come on and stays on for long and there after the head gauge rises pass half mark. What could be the problem? Thank you again.
The clutch is an absolute ball-ache to bleed. You need to be 2 people. Get one of the kids to depress the clutch pedal to build up pressure then you bleed off the air on the concentric slave cylinder. But note it takes for ever.and bleed it again a couple of days later.
@@sumeethsamlall4264 dis you flush the radiator? What coolant are you using? Did You replace the pressure cap on the coolant reservoir?
@@JacoBadenhorst @Jaco Badenhorst I used anti freeze coolant and I have not changed the cap due to the cap seeming to be sealing fine, should I replace that? And I purchased a radiator flush today so I will try that as an option and I'll keep you posted.
@@JacoBadenhorst I managed to get some pressure on the clutch pedal however it won't select any gears and I did not remove the gear selector because I had removed the engine block and replaced everything there including the clutch. Any ideas?
Battery first to unplug my boss
How do I blow the clutch
You mean "Bleed the clutch"? i go through it in the video. it is a bit of a ball-ache. best to have someone help you.
I blew the slave cylinder , what could be the problem ?
Jirre. Daai fokn voels🤣
Jammer. Enigste plek wat ek het om te werk is langs my voëlhokke.
I watched the whole video to see how you bleed the clutch in the end. Hmm, didn't show that.
Sorry about that. There is no place to film down there. It is basically the same as bleeding brakes. Get your son or someone to pump the pedal while you open and close the bleed port.
@@JacoBadenhorst No problem. I did learn that I'm never changing my own clutch haha. I did do my waterpump last weak. That was easy enough. I thought bleading my clutch may help since I'm stuggling to engage second. Sometimes it will go but usually doesn't.
@@gerritgeldenhuys2763 yes bleeding the clutch isn't to much work. Give it a go. Hopefully it's just air in the system and not the clutch plate itself.
How do i bleed my clutch on Ford bantum
On the concentric slave cylinder there is 2 ports. One is the hydraulic input. 2nd is the bleed valve. You will need 2people. Depress the clutch. Pedal. Open the bleed valve to release pressure. Close bleed valve. Release clutch pedal. Depress clutch pedal. Release bleed valve. Close bleed valve release clutch pedal. Repeat till all air is removed.
Injector holeg cleaning video needed fieasta 1.4 tdci