I succeeded to save my tablet with that video but it's a hard job. Pay attention to the way you spread the glue cause you may create bubbles. You don't want that. Thank you Jerry mobile
I separated mine didn't cracked it or anything all of a sudden I put it back together and know my motherboard overheats when I use it bought another motherboard to see if that was the issue and it turns out that the cause of my tablet overheating is the lcd that I just fixed I down load a game called dead trigger and the screen goes crazy and that's without loca glue I'm going to use loca glue and see if the problem goes away.
Hi, I have a Galaxy tab 3, I tried to replace the digitizer but it has glue in the middle of the lcd screen and digitizer. I cleaned up the all the glue and lefted with out glue, now the tablet responds slow, with Lag, do I need to add loca glue or the tabled is broken?
Just to check a couple of things; 1. Does the glue cover the front camera & proximity sensor points on the glass? 2. How do you stop the glue from getting on the lower buttons? - or does it not matter? Thanks
what kind of glue do you use, have you got an internet site where I can Buy it ? . What is the size of the metal wire that you use to separate the glass and the digitizer ? Do you heat the glass after you glue it ? Can we use an other type of glue or an other type of heating ?
@@sjkali408 the supplies are in his description. He gives the links for each product. As for the LOCA glue, you use UV light on not heat, to cure. About 10 mins in sunlight or less using the UV lamp.
What is the layer under the glass? The black plastic film that you leave on. I accidentally got under it with the razor blade and damaged it. I had really bad shatter that was impossible to stay under (kept cutting string) so I ended up pulling he whole thing up after it was damaged. What is the layer and how do I find it?
Będę miał do naprawy Huawei MediaPad T3 10. Z tego co się dowiedziałem to ma on klejony digitizer do ekranu. Czy sam hot air na 100*C i drut molibdenowy wystarczą? Kleić z powrotem na klej loca, czy jednak sobie odpuścić przy LCD? Ile gram kleju potrzeba było na ten 10 calowy tablet?
we changed one,... became extremely slow ! we did update firmware reset the device but still same ! we tried then other supplier... same thing occur !! its a wrongly manufactured part probably what main board doesnt like ! CORRECT? do u have original part it? SM-T580
Jerry thanks for video. On the older tablets the glass had a connector that plugged into the tablet. How does the tab s identify when the glass is touched? Also, can this be repaired without using the special glue and uv light? Thanks
+adriangwatson oc course You can put new glass without LOCA glue, but after some time will be dirt between glass and LCD. In new Samsung tablets and smartphones digitizer working without glass too. Digitizer is integrated with the screen so theoretically You can using device without this glass (but it is dangerous for the screen - of course the screen is very expensive).
@@StreetKingz4Life LCDs are nothing compared to the super AMOLED screens the newer Samsung tablets use. Replacing it on my Tab s6 would've cost $405. Because of the way the super AMOLED screens is designed, virtually no one would just replace the glass, as shown here. Unlike LCD and regular AMOLED, Samsung's new super AMOLED panels basically integrated all the most important layers -- the digitizer, the AMOLED panel, and the front glass -- into a single layer. Because there is now no air space between layers, Samsung claims that the displays are brighter while using less energy. And basically unfixable without a total replacement.
Привет! Сделал свой 8,4". Дольше всего времени заняла очистка дисплея от геля. Хотел спросить: Ты говорил будет видео с Т800 (10,5"). Оно не получилось? Есть ли отличия в стекле под Т805 и Т807 ??? Там какой-то контроллер кнопок видимо находится, и снять его нереально без повреждений, насколько я понял. Я прав? Спасибо за твои видео!
I know this is a stupid question, but.. my samsung galaxy tab s got cracked at one corner, and the thin plastic(?) thing covering the screen didn't have any damage, but the glass under it got cracked pretty badly. That simply means the glass is broken and can be replaced, right? And not that the display or anything important related to the device's system is damaged?
By the sounds of it, you cracked the AMOLED/LCD Display that's under the glass. You can't replace this part alone. If people tried, they'd get complaints by customers for recieving damaged items since AMOLED is literally a piece of thin glass. It's very fragile
+Lol Lol I understand :) Actually I don't have tab 10.5 so I it's impossible. I hope soon I will have one in service - then of course I will record repair process.
Hello Jerry Mobile I followed your guide for the device of a friend ......... I think the real "problem" for the glass change is the glue. In the tablet that I made there was a really high layer, which I was able to completely remove only after 3 hours of cleaning with a spray called E21 ........
Na, not even going to bother. Too much work for a tablet. Samsung needs to make their shit either too tough to break or make it easier to fix or bye bye with their shit. Same with Apple and any other brands that are just messing with our money. Might try the CAT phone with the rugged design and FLIR just because why not
welll.....i screw my touch screen too....so i bought the glass from a guy who works in a factory with10 dollars...and he told me i need somekinda Pro-Vacuum-screen-press-machine if i wanna replace it by myself......can i just put on some glue and stick the new screen on it then put some havy stuff on it and put it in front of fen to blow it dry?????????????????
Verbrannte Displays bzw Polarizer sind dein Markenzeichen, oder? Das sah bei dem Note Edge Video schon sehr abenteuerlich aus und hier wieder. Diesen Gasbrenner halte ich nicht für optimal. Ich hoffe es macht kein anderer nach :)
I need help i've dropped my Samsung Galaxy S2 9.7 and the screen went black, now when I go to turn it on I press my thumb against the home button and I can here the chime telling me I unlocked my tablet then when I press the volume rocker the sound rises and lowers then when I turn it off the chime come on again. So its working but no screen. Also I've tried to shine a flashlight onto the screen and i don't see noting on the screen could have the led screen gone out? Please help me. And is it fixable?
Bad news for me, cracked my Tab S 8.4 this morning in bathroom (tile floor), asked mobile repairers around and no one can fix the glass unless changing the lcd screen, that means bloody expensive, costs more than what the device's worth. I don't think I can change the glass according to the video, it's beyond my capability I'm afraid. Fxxk!
how it can still touched??I have Samsung Tab s 8,4 sm-t705 the touchscreen cracking but still worked but it sometimes touched self(sorry bad english im from indonesia)
+Jerry Mobile how the LCD can touched without glass??i try it on other phone and did not work.how to get the glass,in indonesia not easy to get the original glass it still from chinese.
+Jesua Antonio it is possible becouse digitizer is factory connected with the SuperAmoled screen. In the other phones (for example Sony Xperia J) the digitizer is connected with the glass. So, glass is not necessary for Samsung Galaxy Tab S 8.8 (Note 2, Galaxy S4 and more) but I recommend using device with glass (will be safer). I hope I helped You :)
So you just replaced the glass. My tab s2 glass is broke but it still works. I want to fix it but i am scared I might hit a ribbon or something while removing the glass from the lcd
I tried replcing the glass on my samsung tab s 8.4 and now the screen/lcd is different colours because I held the heat on too long, I want replace it but I just found out the for the replcements on the website I was looking at, the price was more then I paid for the tablet. I dont know what to do
@@Conner._.Anderson I just sent mine to Samsung and they worked out a good price for 100$ to replace my tab s4 lcd which I still have in perfect condition
We Cast the touch screen wil not work allways so you have to put your tablet in standby and then will it work again i dont use glue and it works for me just so i dont mess up with glue
искал в своем городе мастера что бы поменять стекло на такой планшет и все в один голос говорили что он не меняется, потом один мастер отправил к другому и тот мне поменял, заказал с алиэкспресса стекло, поменяли за 2т.р.
Думал это невозможно, наконец то хорошее подробное видео! Мастер!
+Виктор Владимирович Спасибо за эти слова :)
+Jerry Mobile , и Вам Спасибо за комментарии и ответы!
I succeeded to save my tablet with that video but it's a hard job. Pay attention to the way you spread the glue cause you may create bubbles. You don't want that. Thank you Jerry mobile
Thanks Jerry ! I was looking for a very long time since this tutorial !!
Titanssx i
Jerry thanks! Why did you remove every part before putting the screen under the uv lamp? It's so necessary?
great video what type of heat gaun are you using on the screen please
u open the back case wrong... first step is 1:55 the plastic back will follow the gold frame.
Thanks bro...i really appreciate this tutorial.. success
is this applicable also to Tab A series, like Tab A7 Lite?
Thanks for showing us this, I decided to sell it and buy a new one. I would probably break it.
😁😁
Привет! Скажи что за клей? есть такой же , но без инфракрасного света сохнул
super esque you can tell me what is the kind of glue tube? that you use to glue the glass
I separated mine didn't cracked it or anything all of a sudden I put it back together and know my motherboard overheats when I use it bought another motherboard to see if that was the issue and it turns out that the cause of my tablet overheating is the lcd that I just fixed I down load a game called dead trigger and the screen goes crazy and that's without loca glue I'm going to use loca glue and see if the problem goes away.
Hi, I have a Galaxy tab 3, I tried to replace the digitizer but it has glue in the middle of the lcd screen and digitizer. I cleaned up the all the glue and lefted with out glue, now the tablet responds slow, with Lag, do I need to add loca glue or the tabled is broken?
Just to check a couple of things;
1. Does the glue cover the front camera & proximity sensor points on the glass?
2. How do you stop the glue from getting on the lower buttons? - or does it not matter?
Thanks
how much glue do you recommend to use?? 5ml? 15ml 50ml. when actually placing it on the LCD before the glass goes on top???
Here You need +- 7ml
hi there Jerry , can u give me a site for touch screen , hard to find , thank u
Excelente video. No funciona el flash de la camara en mi tab S 8.4 - Que puedo hacer?
Was that screen burn, or did glue get in the LCD on the bottom right? (The pink light area seen after repair)
that's some reflection. It disappears several times as he moves his hand around
Please make a video on tab s2 t810 front glass.
what kind of glue do you use, have you got an internet site where I can Buy it ? .
What is the size of the metal wire that you use to separate the glass and the digitizer ?
Do you heat the glass after you glue it ? Can we use an other type of glue or an other type of heating ?
I have the same questions (for tab 10.5)
Any update?
@@sjkali408 the supplies are in his description. He gives the links for each product. As for the LOCA glue, you use UV light on not heat, to cure. About 10 mins in sunlight or less using the UV lamp.
Hi jerry . did you ever replace glass only on a galaxy tab A 7.0 ?
fiona walsh Hi :) this model never
Can I ship a Tab S2 to you guys to fix? LCD is fine just glass is broke.
Of course, why not 😉 Please message on Facebook
What is the layer under the glass? The black plastic film that you leave on. I accidentally got under it with the razor blade and damaged it. I had really bad shatter that was impossible to stay under (kept cutting string) so I ended up pulling he whole thing up after it was damaged. What is the layer and how do I find it?
Shawn that's the polariser, you can replace it, it's just even more of a pain to do than replacing just the glass
Będę miał do naprawy Huawei MediaPad T3 10. Z tego co się dowiedziałem to ma on klejony digitizer do ekranu. Czy sam hot air na 100*C i drut molibdenowy wystarczą? Kleić z powrotem na klej loca, czy jednak sobie odpuścić przy LCD? Ile gram kleju potrzeba było na ten 10 calowy tablet?
we changed one,... became extremely slow ! we did update firmware reset the device but still same ! we tried then other supplier... same thing occur !! its a wrongly manufactured part probably what main board doesnt like ! CORRECT? do u have original part it? SM-T580
Thanks for sharing and proving the Bill of Materials (BOM)
Could you list where to purchase the metal scrapper you used @ 10:54 ?
Pedro2NR glue
if you have Indian website where I buy this glass tab s...so please give me...link or other way I got it...thanku
Lol this is torture. I am greatly amazed at the patience of the repairing person.
tubeRSP you can say that again lol
Jerry thanks for video. On the older tablets the glass had a connector that plugged into the tablet. How does the tab s identify when the glass is touched? Also, can this be repaired without using the special glue and uv light? Thanks
+adriangwatson oc course You can put new glass without LOCA glue, but after some time will be dirt between glass and LCD.
In new Samsung tablets and smartphones digitizer working without glass too. Digitizer is integrated with the screen so theoretically You can using device without this glass (but it is dangerous for the screen - of course the screen is very expensive).
+Jerry Mobile Thanks Jerry
+Jerry Mobile yup ....almost all LCD'S are expensive
@@StreetKingz4Life LCDs are nothing compared to the super AMOLED screens the newer Samsung tablets use. Replacing it on my Tab s6 would've cost $405. Because of the way the super AMOLED screens is designed, virtually no one would just replace the glass, as shown here. Unlike LCD and regular AMOLED, Samsung's new super AMOLED panels basically integrated all the most important layers -- the digitizer, the AMOLED panel, and the front glass -- into a single layer. Because there is now no air space between layers, Samsung claims that the displays are brighter while using less energy. And basically unfixable without a total replacement.
@@JerryMobilePL Not only dust but also condensation.
Is it the same for tab s6 lite ?
Привет! Сделал свой 8,4". Дольше всего времени заняла очистка дисплея от геля. Хотел спросить: Ты говорил будет видео с Т800 (10,5"). Оно не получилось? Есть ли отличия в стекле под Т805 и Т807 ??? Там какой-то контроллер кнопок видимо находится, и снять его нереально без повреждений, насколько я понял. Я прав? Спасибо за твои видео!
Виктор Владимирович Скажите а чем чистили дисплей. Да откуда надо начинать заводить струну. Опыт есть но тодько с айписи дисплеями. Какие нюансы
May be to ask what wat the light for...
I know this is a stupid question, but.. my samsung galaxy tab s got cracked at one corner, and the thin plastic(?) thing covering the screen didn't have any damage, but the glass under it got cracked pretty badly. That simply means the glass is broken and can be replaced, right? And not that the display or anything important related to the device's system is damaged?
By the sounds of it, you cracked the AMOLED/LCD Display that's under the glass.
You can't replace this part alone. If people tried, they'd get complaints by customers for recieving damaged items since AMOLED is literally a piece of thin glass. It's very fragile
no rush brok but can u do the 10.5 one because my tab cracked and I'm trying to fix it without my dad knowing
+Lol Lol I understand :)
Actually I don't have tab 10.5 so I it's impossible. I hope soon I will have one in service - then of course I will record repair process.
Hello Jerry Mobile I followed your guide for the device of a friend ......... I think the real "problem" for the glass change is the glue. In the tablet that I made there was a really high layer, which I was able to completely remove only after 3 hours of cleaning with a spray called E21 ........
ok so do I need the UV light or can I just put it out in the sun for a few minutes under something clear so no dust sticks ect?
I recommend to use UV lamp.. But of course it will not be bad Your solution
Na, not even going to bother. Too much work for a tablet. Samsung needs to make their shit either too tough to break or make it easier to fix or bye bye with their shit. Same with Apple and any other brands that are just messing with our money. Might try the CAT phone with the rugged design and FLIR just because why not
will the glue dry without the uv light if not can I use the sun?
use the UV light, is better
Jerry can we use led light or any light to harden the glue
khan amrar strong sunlight will harden loca glue
Wish they made the new tabs as easy to repair as this one... :(
hi can i change the glass with an hairdryer and without the glue?
Finally I found Mc Giver
A Dremel/Drill plus a long cotton swap is a great way to remove gunk, in my inexpert opinion
Can i also use a hairdryer or is that not hot enough ?
Brew Ster of course You can, You need about 70 degrees
Wao, estoy jodido... podría llegar hasta el segundo paso, ya después no tengo ni la luz ultravioleta ni la pega...
What is the machine fo heating and glass glue?
what stood temperature at removal? if to heat it to 200 degrees?
80-85 degrees not over, or you'll damage the polarizer film
4ud Ik 85-99 celcius. more than that it will burn like my S5. lucky for me that My S5 still worls even with that white permanent damage
welll.....i screw my touch screen too....so i bought the glass from a guy who works in a factory with10 dollars...and he told me i need somekinda Pro-Vacuum-screen-press-machine if i wanna replace it by myself......can i just put on some glue and stick the new screen on it then put some havy stuff on it and put it in front of fen to blow it dry?????????????????
hello Jerry Mobile, thats a great video ! How much would you charge for that ?
Do you have the 10.5 video available, soon ?
best regards !
wow this looks a right ballache
Brother to brother asked . I want to put a glass sent to Vietnam took how much money
Verbrannte Displays bzw Polarizer sind dein Markenzeichen, oder? Das sah bei dem Note Edge Video schon sehr abenteuerlich aus und hier wieder. Diesen Gasbrenner halte ich nicht für optimal. Ich hoffe es macht kein anderer nach :)
LOL, after 20mins of watch it, Just tell me how much.
my screen is cracked, it charges I can hear it turn on but No Display. .what's wrong work it..what do I need a new screen or the display is fu\ked?
I need help i've dropped my Samsung Galaxy S2 9.7 and the screen went black, now when I go to turn it on I press my thumb against the home button and I can here the chime telling me I unlocked my tablet then when I press the volume rocker the sound rises and lowers then when I turn it off the chime come on again. So its working but no screen. Also I've tried to shine a flashlight onto the screen and i don't see noting on the screen could have the led screen gone out? Please help me. And is it fixable?
The same
I think its still working ,you have to change the Mirror IN the phone and change it and if u said its only a black screen, maybe it will correct
What liquid you add before instal the glass ???
Luis Catania uv glue
Don't you need something to make sure the LOCA doesnt cover the button and sensors?
Run a bead of loca around the edge first and it won't overflow.
у меня ест такой планшет сколко стоит замен стекло
What type of glue you use on this video ?
it is LOCA glue :)
Bad news for me, cracked my Tab S 8.4 this morning in bathroom (tile floor), asked mobile repairers around and no one can fix the glass unless changing the lcd screen, that means bloody expensive, costs more than what the device's worth. I don't think I can change the glass according to the video, it's beyond my capability I'm afraid. Fxxk!
dyu999 mine has had the same fate havent got around to repairs yet.
dyu999 i just did the same thing...meh
how it can still touched??I have Samsung Tab s 8,4 sm-t705 the touchscreen cracking but still worked but it sometimes touched self(sorry bad english im from indonesia)
+Jesua Antonio It is possible that You pushed the glass too hard. The touchscreen is working very good in my device after repair :)
+Jerry Mobile how the LCD can touched without glass??i try it on other phone and did not work.how to get the glass,in indonesia not easy to get the original glass it still from chinese.
+Jerry Mobile 12.51 how it can??
+Jesua Antonio it is possible becouse digitizer is factory connected with the SuperAmoled screen. In the other phones (for example Sony Xperia J) the digitizer is connected with the glass. So, glass is not necessary for Samsung Galaxy Tab S 8.8 (Note 2, Galaxy S4 and more) but I recommend using device with glass (will be safer).
I hope I helped You :)
+Jerry Mobile thanks but i don't have UV ligh and LOCA glue,i will describe and like this video.how much you pay for the glass??
This vid helped with my s2, I don't know why Samsung makes it so complicated, probably so you have to buy the 150 dollar LCD+glass part
So you just replaced the glass. My tab s2 glass is broke but it still works. I want to fix it but i am scared I might hit a ribbon or something while removing the glass from the lcd
I tried replcing the glass on my samsung tab s 8.4 and now the screen/lcd is different colours because I held the heat on too long, I want replace it but I just found out the for the replcements on the website I was looking at, the price was more then I paid for the tablet. I dont know what to do
FlyingFox429 buy a new tablet
Boss magkano po pagawa nabasag po kc screen Samsung Galaxy Tab S 8.4? Salamat po
terima kasih infonya gan... nice
Hm Ang parepair Ng tab na ganyan shot down na ayaw Ng ma open...at palit ndin Ng lcd
why are u not beginning at the top of the device, to seperate the glass?
thats much easier...
Omfg!! This worked perfectly!!!!
you show us now how it came the job? You have not soiled the backlight with the loca glue?
There are no backlight in AMOLED screens. All of the Amoled screens are waterpoof
amoled emit their own light. Are different from lcd
Does this work for the tab S4
Did you ever find a way?
@@Conner._.Anderson I just sent mine to Samsung and they worked out a good price for 100$ to replace my tab s4 lcd which I still have in perfect condition
Where can I get the new glass ?
without audio same?
nice
Does anybody have experience with just the glass swap of a samsung galaxy s2 tablet?
how use Sim card
Jerry can I pay you to sort mine out
hi how to repair if it's screen is broken
Prakash Bharat You have to buy full screen module and mount it
how much will it cost. some say it's very expensive for 8 inches screen
s.click.aliexpress.com/e/NJ2FURb
Prakash Bharat check it's a good store
+Jerry Mobile thankuu
dude use more heat, that was painful to watch
maybe just the lighting?
Gah. This is quite scary. I don't trust myself to successfully pull this off tbh.
the link forr the glue doesnt work
+FlamingFoxIgnited Thank You for this information. I just fixed it :)
Yep
buy the buy the lcd dgitiser and glass in one. $10 more, but 1 billion times easier and better.
Galaxy Tab S 8.4 Glass Only Repair (FULL GUIDE)
Audio not playing
what if I dont put glue
We Cast the touch screen wil not work allways so you have to put your tablet in standby and then will it work again i dont use glue and it works for me just so i dont mess up with glue
Can't Reacher This Shop
а экран поцарапал лопаткой.
привет из Москвы!
by next week or 2
искал в своем городе мастера что бы поменять стекло на такой планшет и все в один голос говорили что он не меняется, потом один мастер отправил к другому и тот мне поменял, заказал с алиэкспресса стекло, поменяли за 2т.р.
как в итоге получилось, не начал ли клей менять цвет?
как в итоге получилось, не начал ли клей менять цвет?
+AGL Sherer сегодня 3 день, пока полет нормальный
+AGL Sherer правда несколько мелких пузырьков осталось как точки, видны на белом экране, в остальном я доволен
+AGL Sherer правда несколько мелких пузырьков осталось как точки, видны на белом экране, в остальном я доволен
You disassemble it wrong..that back part you remove 1st shouldn't have come off like that..dwl
Not much use without sound and a narrative...
holy crap this is complicated.
that's great, lcds smashed
Galaxy
Joaocareiro
or buy the S3 Tab for $79
you so fast bro
mobile phone repair HSR Mandawali
mobile phone training worker
Biedny tablet
I need my phone fix
Please message on Facebook ;)
@@JerryMobilePL ok