In my opinion those old carbs are a lot better. I bought a new one and have had nothing but trouble. I dealt with constant vacume leaks and only got it working tonight.
@@crankshaftgarage5722 I see , have any issues with the new filter ,as I saw I few vid where people say after installing the rc carb filter it ran to rich ,carb not being able to breath well due to the filter matiral ?
@@crankshaftgarage5722 Im not really that technically minded , just learning from these videos ,saw I bloke on here who was tinkering with the idea , be interesting to see what happens lol
@@dangerousdoggo5465 you technically can supercharged a 2 Stroke, as for turbo it is also possible. It's possible, doesn't mean it would require alot of work, hard determination, and knowledge. But it is possible
Well the main reason a did this is to protect the engine from dirt and sand being sucked into the combustion chamber ( their where gaps in the old filter) and to make it easy to clean. I've been busy and had to put the project on hold and I haven't been able to test it yet, but when I do (hopefully soon) I will post updates on it. Thank you for watching!
Furkan Yıldırım_Pro it was never about power it was improving its running power your engine runs more efficiently when it can breathe better and get a better mix of air to fuel mixture
the jet needle is at the bottom, the throttle cable comes in at the top. if you mean the e-clip on the jet, it is at the middle setting. but the best setting for it depends on your altitude.
If I use a 50mm air filter will it fit with out cutting up the old one
You replaced the air box not the intake. And all you have to do is drill some holes in the old one and it'll flow fine
In my opinion those old carbs are a lot better. I bought a new one and have had nothing but trouble. I dealt with constant vacume leaks and only got it working tonight.
Is the 60mm the air cone filter rubber fitting that goes around the stock air filter
Your exactly right, it is. Thank you for your comment.
5:03 is that jb weld?
Can i ask why u put sealant on the old part of air filter when u scew it to the carb before u fit the new filter ?
It had gaps around it which can let in dirt and sand.
@@crankshaftgarage5722
I see , have any issues with the new filter ,as I saw I few vid where people say after installing the rc carb filter it ran to rich ,carb not being able to breath well due to the filter matiral ?
@@crankshaftgarage5722
Im not really that technically minded , just learning from these videos ,saw I bloke on here who was tinkering with the idea , be interesting to see what happens lol
@@crankshaftgarage5722 Supercharging a 2 stroke???? What are you even talking about? You need to read up on 2 stroke engines... Go read a book!
@@dangerousdoggo5465 you technically can supercharged a 2 Stroke, as for turbo it is also possible. It's possible, doesn't mean it would require alot of work, hard determination, and knowledge. But it is possible
i actually just 3d printed a bracket
have you noticed a difference?
Well the main reason a did this is to protect the engine from dirt and sand being sucked into the combustion chamber ( their where gaps in the old filter) and to make it easy to clean. I've been busy and had to put the project on hold and I haven't been able to test it yet, but when I do (hopefully soon) I will post updates on it. Thank you for watching!
@@crankshaftgarage5722 Lol the other filter protects more than this mesh one. the gas on the sponge is good because it stops dust....
This wont get you any power.
Filter replacement won't get power. Only good looking.
Furkan Yıldırım_Pro it was never about power it was improving its running power your engine runs more efficiently when it can breathe better and get a better mix of air to fuel mixture
@@greenmachine55 that may be true but honestly it made my bike slower....
If you adjust your mix right too add more fuel than you do with the stock filter you should get more low and higher end torque
What is your jet needle setup? Are you at the top or the middle or the bottom?
the jet needle is at the bottom, the throttle cable comes in at the top. if you mean the e-clip on the jet, it is at the middle setting. but the best setting for it depends on your altitude.
I use .60 jet
Furkan Yıldırım_Pro what’s the default jet?
you should lazer print these parts sell them on ebay.com
you should sell these mods on ebay.