Hey Luis that was a great diagnosis but here's a tip from an old guy. From the days when cars had distributors and points, the points had a good thick layer of platinum plating. You could file off the burnt parts and everything was OK. Then the manufacturers started to economise, the platinum got thinner and nowadays I think that they are all just silver plated. Not just in cars but in things like fridge thermostats. This plating is a very thin layer over a brass or steel contact, after you have cleaned it it will not last very long. I was once given a really nice washing machine, it was built like a tank but the contacts in the mechanical programmer were burnt. I cleaned them but after two weeks they failed again. All the silver plating was gone. Anything that draws a high current and has an inductive load will give you the same problems. I hope that this helps anybody out there. It is a shame to buy new parts but sometimes you may need to. P.S. I'm not entirely sure but if you switch off the ignition with the wipers still running would the back EMF* make a spark across those contacts? Hopefully someone will know :) *The back EMF is caused by the collapsing magnetic field (in for example, an electric motor) inducing a reverse voltage in the circuit. That's why some relays have a diode inside, it's to short that voltage across the coil and stop it harming the rest of the circuit.
Well diagnosed and repaired . At one point I was thinking bad earth somewhere on relays . Your channel is great to watch!!! i like the way you use your skills to repair rather than replace parts. Imagine what the bill would have been at a mercedes garage for this fix. Thankyou for sharing your knowledge for us all to see. regards Rich
well done, took a bit of sorting but you got it done, I ask myself what have we gained from all these electronics, millions of man hours lost everyday because of (in this case) a coked contact. In the old days you had 2 wires and a switch, you switched it on, and you switched it off, it worked .. and if it didn't it took 10 mins to fix.
great video good you found voltage drop on sam going back to switch you checked feed with meter not under load just listing felt like power ground failing under load keep them videos coming always look forward to the next one thanks
Good video. Thanks. My ML350 front wipers are not working. I believe the motor is good by applying power via connector pins. The fuses are good in the fuse box. After turning key to ignition position, I find no power 12V shown on the wiper fuse terminals. Is this correct? All other fuses’ terminals can get 12V except the Horn fuse. However, the Horn does work good. Appreciate any suggestion?
@@LMAutoRepairs Thanks for the suggestion. After finding no problem to the pump and the motor, seeing no power on the fuse terminals, reconnect the battery, the washer and wipers are back to work now! I remember saw a TH-cam video. The guy has taken all wiper a part, test motor and finding no problem. The wiper begins to work after putting parts back. His comment, don't know what are reasons caused failure but hope the video shows you a good way of taking wiper into parts. I feel the same way, cannot figure out the failure reason. Though I did clean up the washer pump robber filter clogged residues.
Hey great video hope you're still doing your thing I have that exact problem with the ignition and was wondering if that can also cause an airmatic fault. Sometimes the car lifts sometimes it doesn't. The problem has gotten worse I can no longer jiggle the ignition to make my wipers work and now the car doesn't lift at all
@@LMAutoRepairs the ignition is causing many problems. The wipers used to work by jingling the ignition and can't shift out of park without jiggling the ignition also when I press on the brake the SOS light and the gear shift lock light blinks and the radio cuts out. I've been having problems with the airmatic sometimes it goes up sometimes it goes down. And now that jiggling the ignition for making the wipers work does not work anymore the car also does not rise anymore I recently put a wire to a switch from that red power wire in your video to make my wipers work. And if the relay for the airmatic is on the same side that may not be getting power I'm assuming that it could also be causing the issue with it rising up and down. Sorry for the long paragraph and thank you for your help
@@LMAutoRepairs what you did to that ignition was it just a temporary fix or did solve the problem completely. You just clean the contacts and bent the contacts.my Car won't rise so it's not drivable .so I might as well try to do that same job myself before buying a used one and cloning
Great video. My 2006 S500 lately started having wiper and washer problems. Sometimes they work and sometimes don't work. When they don't work, the SOS and the brake light flickers on/off when I try engaging the wiper or washer. Any suggestions on the problem would be very appreciated.
Difficult to say... Could be something similar to this, but without checking/diagnose it is pure guess work... Scan it, check some live data and go from there... Thank you for watching!
Vipers not working and My washer dont work either, Have check Fuse and relay and they ok..... can it maybe be the viperarm in car ... strange that both breakdown at same time......? (W203 c200 2001)
@LM Auto Repairs This is really weird....?! Took a grip around wipers and ”shake it” and both the washer and wipers work 🤪🤔 Soooo.... it must be a co-operation between wipermotor and washer...... guess it is the motor after all ....?
lol the customer has been waiting for over 6 months He has to go the long way round got to use a reader first and then replace working sensors he dont realize sensors are there to show the fault he is funny
Great video I have a 2006 kompressor W203 M271 with the same problem check the fuse and relays and it look good and I did also buy another wiper motor put it on but it still on working. Regard Nigel
I have a 2010 C300 4 Matic, wipers will not work . I need a quick fix . Wiper motor is good . Can u tell me how to wire direct power to this wiper motor so I can hook up to a toggle switch for now . I would appreciate any help . BTW I like your vids very good work you do .
@@LMAutoRepairs I have tried Google and fb pages , no help . I have watched hours of vids and nothing bc No one has this problem. Been working on this for 3 weeks . Wipers won't work . Has power to motor ,motor is good , switch is good all fuses and relays are good . All started after I fixed the esl motor . No wipers and airbag light on dash now . Triple checked everything I took apart .
@@LMAutoRepairs front left srs malfunction and front right parking lamp . Parking lamp has been on for few months . I don't have a scan tool for this car to get codes unfortunately. I figured I disturbed something as well , took it apart 3 or 4 times since and didn't find anything wrong with wires. Well the headlight switch didn't work either after I did the esl , took back apart and checked connections and light switch works just fine now . Just the wipers won't work .
The oil temperature sensor is a common issue with the OM 642 engine. Mercedes made a revised component which is what your customer should have put in. If I can find the new part number I will post up on here. Where did you get your Star machine from? I remember you saying a while ago a company that you use (and not promoting) but I have lost the link to them. Can you please help?
THANK YOU FOR ANOTHER GREAT VIDEO! Yes it is imposible to repair car without wiring diagram somethimes. Maybe it is but then you don't need scanner, scope, nothing. Maybe this is posible I don't know. Even if it is, it would require much more time I'm sure. In this case how one would know where that wire was going without diagram. Greetings from Serbia.
@@LMAutoRepairs i guess OEM stand for original equipment manufacturer. Is there any specific software that can be used for all Japanese car or all German cars or you have to get a different tools and software for each?
The EIS is pronounced like ice cream without the cream as it's German as a E is a eh and letter I is a E lol to add some more to the abriviaton confusion. I had loads of trouble spelling in English with these 2 for years as my name has E and y in English complete different named.
I do love the way you find the fault and repair these things. Not one part swapped.
Thanks!
For watching and for your comment!
👍👍👍👍
Hey Luis that was a great diagnosis but here's a tip from an old guy. From the days when cars had distributors and points, the points had a good thick layer of platinum plating. You could file off the burnt parts and everything was OK. Then the manufacturers started to economise, the platinum got thinner and nowadays I think that they are all just silver plated. Not just in cars but in things like fridge thermostats. This plating is a very thin layer over a brass or steel contact, after you have cleaned it it will not last very long. I was once given a really nice washing machine, it was built like a tank but the contacts in the mechanical programmer were burnt. I cleaned them but after two weeks they failed again. All the silver plating was gone. Anything that draws a high current and has an inductive load will give you the same problems. I hope that this helps anybody out there. It is a shame to buy new parts but sometimes you may need to.
P.S. I'm not entirely sure but if you switch off the ignition with the wipers still running would the back EMF* make a spark across those contacts? Hopefully someone will know :)
*The back EMF is caused by the collapsing magnetic field (in for example, an electric motor) inducing a reverse voltage in the circuit. That's why some relays have a diode inside, it's to short that voltage across the coil and stop it harming the rest of the circuit.
Thanks for the advice!
For watching and for your comment, really appreciated!
👍👍👍
Well diagnosed and repaired . At one point I was thinking bad earth somewhere on relays . Your channel is great to watch!!! i like the way you use your skills to repair rather than replace parts. Imagine what the bill would have been at a mercedes garage for this fix. Thankyou for sharing your knowledge for us all to see. regards Rich
Hi
Thank you for watching and for your kind comment!
Appreciated!
👍
It looked like someone had drowned the switch box in contact cleaner but didn't want to open it up.
Well done, Luis.
😃
Lol
Thank you for watching and for your comment!
Thank you for the video. I purchased a 2006 us spec s500. My issue ended up being identical. Your video helped me resolve the issue.
That's great!
Thank you for watching and for your comment!
👍👍👍
This video was incredibly helpful. Identical situation with a car in our shop, the was THE FIX. Thank you
☺
Thank you for watching and for your comment!
👍👍👍
well done, took a bit of sorting but you got it done, I ask myself what have we gained from all these electronics, millions of man hours lost everyday because of (in this case) a coked contact. In the old days you had 2 wires and a switch, you switched it on, and you switched it off, it worked .. and if it didn't it took 10 mins to fix.
😊👍👍👍
Good work! It's getting harder to find people that know what they are doing these days...
😊
Thanks... for watching and for your comment!
Amazing detective work and repair!!
Hi
Thanks...
For watching and for your comment!
👍👍👍
Very clever man as usual,look forward to the next video. Thanks
Thank you for watching and for your comment!
👍👍👍
great video good you found voltage drop on sam going back to switch you checked feed with meter not under load just listing felt like power ground failing under load keep them videos coming always look forward to the next one thanks
Thanks.. for watching and for your comment!
👍
I have a problem with my wipers on a w203 cdi 220 my wipers stop working when im driving over about 5mph horn also stops working and possibly mirrors
first i like then i watch, because i know what to expect.You are the man...
😋
Thank you for watching and for your comment!
Is w211 the same set up? Wipers are not working, but will work on the Washer when you need to clean windscreen.
Wow what a great job!! What I can use to clean that kind of parts?
I use isopropyl alcohol...
👍👍👍
Good video. Thanks. My ML350 front wipers are not working. I believe the motor is good by applying power via connector pins. The fuses are good in the fuse box. After turning key to ignition position, I find no power 12V shown on the wiper fuse terminals. Is this correct? All other fuses’ terminals can get 12V except the Horn fuse. However, the Horn does work good. Appreciate any suggestion?
You need to scan and look at some live data...
Otherwise is like chasing a ghost...😊
👍👍👍
@@LMAutoRepairs Thanks for the suggestion. After finding no problem to the pump and the motor, seeing no power on the fuse terminals, reconnect the battery, the washer and wipers are back to work now! I remember saw a TH-cam video. The guy has taken all wiper a part, test motor and finding no problem. The wiper begins to work after putting parts back. His comment, don't know what are reasons caused failure but hope the video shows you a good way of taking wiper into parts. I feel the same way, cannot figure out the failure reason. Though I did clean up the washer pump robber filter clogged residues.
Do you suspect the same failure for the American version - driver seated on the left?
Great Troubleshoot. Where do you get the wiring diagrams?
Hi
It is possible... but you will have to test...
I have WIS...
Thank you for watching!
👍👍👍
Hey great video hope you're still doing your thing I have that exact problem with the ignition and was wondering if that can also cause an airmatic fault. Sometimes the car lifts sometimes it doesn't. The problem has gotten worse I can no longer jiggle the ignition to make my wipers work and now the car doesn't lift at all
It is possible, but o would think if was the ignition it would cause other issues...
Try to scan the car, and see what it going on...
👍👍👍
@@LMAutoRepairs the ignition is causing many problems. The wipers used to work by jingling the ignition and can't shift out of park without jiggling the ignition also when I press on the brake the SOS light and the gear shift lock light blinks and the radio cuts out. I've been having problems with the airmatic sometimes it goes up sometimes it goes down. And now that jiggling the ignition for making the wipers work does not work anymore the car also does not rise anymore I recently put a wire to a switch from that red power wire in your video to make my wipers work. And if the relay for the airmatic is on the same side that may not be getting power I'm assuming that it could also be causing the issue with it rising up and down. Sorry for the long paragraph and thank you for your help
Looks like you have the same issue as I had in the video...
☺️
@@LMAutoRepairs what you did to that ignition was it just a temporary fix or did solve the problem completely. You just clean the contacts and bent the contacts.my Car won't rise so it's not drivable .so I might as well try to do that same job myself before buying a used one and cloning
@steved6275
It sorted the problem once for all in this case...
Fantastic work my friend. I am sure with your level of skills they keep you busy. Thank you for your hard work. Cheers 👍👍
😋
Indeed busy...
Thank you for watching!
Hello friend, maybe you have the electrical diagrams of the C180 Kompresor year 2006 W203
Can i easely jump it ?
Thank you
Great video. My 2006 S500 lately started having wiper and washer problems. Sometimes they work and sometimes don't work. When they don't work, the SOS and the brake light flickers on/off when I try engaging the wiper or washer. Any suggestions on the problem would be very appreciated.
Difficult to say...
Could be something similar to this, but without checking/diagnose it is pure guess work...
Scan it, check some live data and go from there...
Thank you for watching!
Hey how's it going did you ever figure out that problem. I'm having the same exact issue
LUIS, Awesome and brilliant fix waiting for the next one to learn more and more and appreciate the time ur spending to do those videos.cheeeeeers
Thanks!
Appreciate you comment and your time watching my videos!
👍👍👍
4 Epc sometimes work this, start engin and turn stearing wheal left hold 3 sec and right 4 3 sec after middle position...
Vipers not working and
My washer dont work either,
Have check Fuse and relay and they ok..... can it maybe be the viperarm in car ... strange that both breakdown at same time......? (W203 c200 2001)
Hi
Yes... strange that both failed at the same time... but is possible...
Can you not scan the car first?
Thank you for watching!
I have done that with Icarsoft but it aint get no code at all..
@@freddomfigeri193
What about live data?
I don't know that tool... might not be able to go that deep into the modules...
@LM Auto Repairs
This is really weird....?!
Took a grip around wipers and ”shake it” and both the washer and wipers work 🤪🤔
Soooo.... it must be a co-operation between wipermotor and washer...... guess it is the motor after all ....?
@@freddomfigeri193
Lubricate the shafts and linkages if they are getting seized...
👍
i wonder why you didnt start your diagnosis with a wiring diagram?
great job, thanks! do you have another video on how to de-solder the EIS to inspect?
No sorry...
How much did you charge him..lots l hope , cause it's taken you day to fix !!
Lol
Thank you for watching and for your comment!
lol the customer has been waiting for over 6 months He has to go the long way round got to use a reader first and then replace working sensors he dont realize sensors are there to show the fault he is funny
Very smart man I like ur style of guessing and testing
Thanks!
👍👍👍
Hi what diagrams did you use to find the fault....
Mercedes ones....
Thank you for watching!
Fantastic. So what has higher quality electrics BMW or Merc? The Merc looks very cheap to me.
I would not look at it like that... they both have quite good quality electrics, but they both have flaws and weak points...
Thank you for watching!
Which programe u have to check about circuit of wiper I have no program for that please im waiting for answer
Mercedes WDS...
👍
Great video I have a 2006 kompressor W203 M271 with the same problem check the fuse and relays and it look good and I did also buy another wiper motor put it on but it still on working.
Regard Nigel
Hope you find your issue...
🤞
👍👍👍
The thing is I don't know where too start,
Oh my G-d ! You are clever man thanks for your video It was great for me
😋
Thank you for watching and for your comment!
Love you profile pic bruv.
thank you for the video....very clear and learning very much from your video's
Thanks!
👍👍👍
Very good video .
Can you make video of parking brake mine are not working
Whenever I have one...
Thank you for watching!
Nice work Luis big thumbs up 👍
Thanks Allan!
👍👍👍👍👍
Excellent work man,,, I love working with Benz, competition
Thanks!
👍👍👍
Another great video Luis. You're troubleshooting skills are fantastic.
Where did you learn your skills? Self taught, college? Thanks.
Hi
Self taught...
Thank you for watching and for your comment!
@@LMAutoRepairs Even more impressive then
@@keitho77
Thank you!
2006 c320 benz wipers not working
شكرا 🙏
I have a 2010 C300 4 Matic, wipers will not work . I need a quick fix . Wiper motor is good . Can u tell me how to wire direct power to this wiper motor so I can hook up to a toggle switch for now . I would appreciate any help . BTW I like your vids very good work you do .
I would have to look at the diagrams for that...
Have you tried to Google it?
Thank you for watching and for your comment, really appreciated!
👍👍👍
@@LMAutoRepairs I have tried Google and fb pages , no help . I have watched hours of vids and nothing bc No one has this problem. Been working on this for 3 weeks . Wipers won't work . Has power to motor ,motor is good , switch is good all fuses and relays are good . All started after I fixed the esl motor . No wipers and airbag light on dash now . Triple checked everything I took apart .
@@ferrellcat5860
So... must be something you have disturbed...
What codes do you have, on the airbag module and Sam?
@@LMAutoRepairs front left srs malfunction and front right parking lamp . Parking lamp has been on for few months .
I don't have a scan tool for this car to get codes unfortunately.
I figured I disturbed something as well , took it apart 3 or 4 times since and didn't find anything wrong with wires. Well the headlight switch didn't work either after I did the esl , took back apart and checked connections and light switch works just fine now . Just the wipers won't work .
@@ferrellcat5860
Try to get is scanned and actuate the wipers... if they work from the scan tool, then you narrow the problem down...
The oil temperature sensor is a common issue with the OM 642 engine. Mercedes made a revised component which is what your customer should have put in. If I can find the new part number I will post up on here.
Where did you get your Star machine from? I remember you saying a while ago a company that you use (and not promoting) but I have lost the link to them. Can you please help?
Hi
Thanks...
👍👍👍
Cardiagtool.co.uk
@@LMAutoRepairs Thanks.
Great video I have a similar problem to this
Excellent , great work
Thank you for watching and for your comment!
Simply u are genious
😋
Lol... thank you for watching!
THANK YOU FOR ANOTHER GREAT VIDEO!
Yes it is imposible to repair car without wiring diagram somethimes. Maybe it is but then you don't need scanner, scope, nothing. Maybe this is posible I don't know. Even if it is, it would require much more time I'm sure. In this case how one would know where that wire was going without diagram.
Greetings from Serbia.
Indeed.. 👍
Thank you for watching and for your comment!
Excellent video.
Thanks!
👍👍👍👍
Sorry to bother bruv What software do you use for those mercedes and the Panasonic you using am not familiar with it.
Thank you.
The OEM software...
Xentry/DAS
Thank you for watching!
@@LMAutoRepairs i guess OEM stand for original equipment manufacturer. Is there any specific software that can be used for all Japanese car or all German cars or you have to get a different tools and software for each?
@@dashtyATG
You have OEM for each manufacturer...
@@LMAutoRepairs so let's say u using this Xentry / DAS software for benz is it possible to be used for all the mercedes benz.
@@dashtyATG
Correct...
Like ISTA is used for all BMWs...
ODIS for all VW...
Etc...
Very interesting video brilliant diagnosis.😚Thanks
Hi
Thanks!
👍👍👍
Great repair mate but i didnt like the temp repair they done its an S class merc lol
Me neither... lol
Thank you for watching and for your comment!
Useful video 👍 Excellent 👍
Thanks!
Thanks, good job👍
Hi
Thank you for watching and for your comment!
👍
The EIS is pronounced like ice cream without the cream as it's German as a E is a eh and letter I is a E lol to add some more to the abriviaton confusion. I had loads of trouble spelling in English with these 2 for years as my name has E and y in English complete different named.
LOL
The important is you guys know what we are talking about! lol
Thank you for watching!
Nice video
Hi
Thank you for watching and for your comment!
Esl is electronic steering loock
👍👍👍
greate video
Thank you for watching!
super
Thank you!
Get to the point mate
I did...
😅
Thanks! Fantastic work!
Thanks!