𝚃𝚆𝟸𝟶𝟶 𝚔𝚒𝚌𝚔 𝚜𝚝𝚊𝚛𝚝 𝚒𝚗𝚜𝚝𝚊𝚕𝚕𝚊𝚝𝚒𝚘𝚗

𝟸𝟶𝟸𝟶 𝙹𝙰𝙽 𝟸𝟿--𝙸 𝚒𝚗𝚜𝚝𝚊𝚕𝚕𝚎𝚍 𝚊 𝚔𝚒𝚌𝚔𝚜𝚝𝚊𝚛𝚝 𝚘𝚗 𝚖𝚢 '𝟷𝟿 𝚃𝚆. 𝙸 𝚏𝚘𝚕𝚕𝚘𝚠𝚎𝚍 𝚝𝚑𝚎 𝚜𝚎𝚛𝚟𝚒𝚌𝚎 𝚖𝚊𝚗𝚞𝚊𝚕.
[𝙾𝚒𝚕 𝚜𝚎𝚊𝚕 𝚊𝚝 𝚝𝚑𝚎 𝚎𝚗𝚍 𝚒𝚜 𝚙𝚞𝚜𝚑𝚎𝚍 𝚒𝚗 𝚘𝚗 𝚝𝚑𝚎 𝚌𝚛𝚊𝚗𝚔𝚌𝚊𝚜𝚎 𝚌𝚘𝚟𝚎𝚛 𝚠𝚑𝚎𝚗 𝚌𝚕𝚘𝚜𝚒𝚗𝚐 𝚒𝚝 𝚋𝚊𝚌𝚔 𝚞𝚙, 𝚋𝚞𝚝 𝚜𝚘𝚖𝚎𝚑𝚘𝚠 𝚝𝚑𝚒𝚜 𝚍𝚒𝚍 𝚗𝚘𝚝 𝚖𝚊𝚔𝚎 𝚒𝚝 𝚒𝚗 𝚝𝚑𝚎 𝚟𝚒𝚍𝚎𝚘. 𝚃𝚑𝚎 𝚙𝚕𝚞𝚐 (𝚘𝚗 𝚝𝚘𝚙 𝚘𝚏 𝚝𝚑𝚎 𝚋𝚘𝚡 𝚠𝚑𝚎𝚗 𝙸 𝚊𝚖 𝚝𝚎𝚜𝚝𝚒𝚗𝚐 𝚝𝚑𝚎 𝚔𝚒𝚌𝚔𝚜𝚝𝚊𝚛𝚝) 𝚜𝚒𝚖𝚙𝚕𝚢 𝚐𝚘𝚎𝚜 𝚒𝚗 𝚝𝚑𝚎 𝚑𝚘𝚕𝚎 𝚊𝚝 𝚝𝚑𝚎 𝚋𝚘𝚝𝚝𝚘𝚖 𝚘𝚏 𝚝𝚑𝚎 𝚔𝚒𝚌𝚔𝚎𝚛.]

[@alisalehi9793]

thank you for your training ,ali from iran 🇮🇷🙏🤝🇺🇸

[@DavidZack-Jeephead]

Most important part is around 4:00 in. Pay attention to where retainer spring and kick stop land. Thank you for this video. Huge help. Finally completed install.
Here is a parts list:

[@James_P60]

I’m looking at buying a 2000 which has the kick on it already but if I ever have issues these two videos you made are saved so I can watch them over and over befor I dig in if I have to, you are definitely a inspiration to many, thanks for taking the time to do these.

[@EnduringGuerila]

Basically a perfectly tutorial, no words needed. Thanks!

[@gillianaustin5849]

That was useful. Thankyou. My Regards Mr. Dominic James Austin.

[@dring83]

good job kiddo!!!!!!!!!!!!!

[@kazroth886]

Well done and very informative. Thx

[@Zoofactory]

That was so hot. 😂❤

[@HuntingLionfishAruba]

Thanks. Great video

[@XXXCRSPL]

Awesome Video Thank You!!

[@libertyforamericanow]

Thanks for the video. These kits are becoming hard to get. I just found the complete setup at a very old motorcycle junkyard for 40 bucks. So lucky

[@danking9745]

Excellent Video. Thanks.

[@briangee4561]

holy shit you're awesome. I'd give this a mill likes if i could. bought a used 06 with 2k miles and now a lil over 4.5k. Been wanting to put a kick on it and finally searched for a vid and found yours. Going to slap one of these bad boys on since i have to replace a gasket from the bottom end either way. thank you so muuuuch, shout out from Cali!! If youre near the area, hmu for a ride sometime!! :) ride safe! thannks again

[@briangee4561]

Just finished my top end Rebuild and installed my kickstart components! Took a whole 24 hrs over today and yesterday lol.
One note is when I went to install my idle gear, it had a spacer of some sort? Not sure if it was from factory or what but it had a snap ring on top so I pulled it off and the spacer and then everything fit :) unfortunately haven't had a chance to kick it yet because I tried to go the cheap route and save a few buck by ordering a kick lever from eBay but it didn't fit even tho they specifically said it would fit 16 mm :( gotta get another one and wait till I can test it. Other than that everything went smooth 😁 thanks again for the sick video! Helped a ton 👍🏾

[@briangee4561]

@@WrongLogic omg idk how I didn't see you pull it out hahaha I kept going back n fourth between both your videos trynna find out what it was. Now I know 😂

[@mnlogan519]

Very well done! Thanks for your efforts, going to make my install a breeze.
-morgs boyfriend who's too lazy to sign into his own account

[@davidbaskin2478]

WHERE CAN YOU BUY A KIT...AND VISE GRIP TOOL!

[@MindBodySoulOk]

That's awesome. Is there already a hole in the case with just a plug in it? missed that part.

[@minnesotahawk4090]

Great video

[@Myersarch77]

Thank you

[@beco89inc50]

Where did you get the kickstart kit from? I’m needing this info to get my own set up. Please help me

[@weldweld5629]

Excellent job where did you get the kit??

[@wolfymaceastern6072]

Hi any idea if the tw200 parts fit the 125=cheers

[@nahtanojrekab]

Hey Mio. Thanks again or your videos. I finished my install and have a bit of grinding after a kick start! Oh no!. In the subtitled video you install the idle gear with the smooth side out but in this video you do the opposite. Which way is correct?

[@DavidZack-Jeephead]

I have same issue. Installed gear smooth side out.

[@antoinelastreet]

Hello, great video, just a question, where to find this complete kit

[@alxmomo1073]

Thanks a lot for this great tutorial ! Could you send me where you bought your kick kit ? It's hard to find one.. Thanks a lot keep the good work !

[@SERBIAZ]

You need to buy the individual parts

[@PUJARTIAGO77]

Where can I get one is that a kit?

[@DerekF242]

Sweeeeet! Bought all the parts a few years back on boats.com and have yet to tackle the install. This is motivation!

[@beco89inc50]

You got the kickstart kit from what website? Also what was the cost...?

[@beco89inc50]

Maybe even a part #.....?

[@DavidZack-Jeephead]

Just ordered parts today May 8th,2023. Came to $438

[@theshirehighlander7292]

Please post a link because I can't seem to find the parts. I have been coming here the past two years to find someone who bought the parts

[@miszek4207]

rad!
is it the same gear n stuff for the tw-125?

[@sies5580]

it is. well later 2000 model

[@samsungtaco11]

what do you call that weird looking vice grip wrench?

[@WrongLogic]

Hi, are you referring to the clutch hub holding tool

[@cajovaresto]

On this video you placed the idle gear smooth side in, on your other captioned video you write, smooth side out. Which is the correct one?

[@WrongLogic]

both worked but depending on part number it might be different; look at the gear teeth

[@ThePepe75035]

what is the kick starter part number

[@juandiaz-nz4ou]

Hello, i from colombia owner of a xt 225 2007 , i want install this piece , this is possible in my bike , and one link for buy this product thanks 😊

[@user-np4fe2hq7b]

How hard was this to do?

[@ronalddelafuente1000]

Where did u get the kickstart kit?

[@kenallen7795]

Partzilla u can find all of it

[@kingjulien4132]

@@kenallen7795 what's the link

[@mr.weaver2682]

Do you have a link for the kick starter kit? I’m looking for one for my 2019.

[@mr.weaver2682]

Mio thank you very much for the link.

[@robdallas3999]

My kickstarter wont budge when i put the case back on,,,works fine without case ? Is there a trick i dont know about? My mechanic couldn’t figure it out and dealer never heard of the problem?

[@jacobdelgado7343]

You godamn angel, your old mans teaching you right.

[@kingjulien4132]

Can someone send me a link to find the kit

[@paulanderson388]

I don't think the kit is still available from Yamaha. You can buy the individual pieces from Yamaha if you have a patient parts man.

[@hedsy]

How come you skipped the clutch alignment process!? That's a very important step!!

[@WrongLogic]

I didn't skip it, just never filmed it. This was never meant to be a tutorial, just wanted to document where the parts went. But I made a second video since people have made all sorts of comments like not showing them how to punch out the plug for the kick shaft to go through which I think is so basic but never realized was such a big deal for others.

[@VoidedWarranty]

yeah I find people often neglect step 1: read the service manual for all of the parts that are going to be removed and reinstalled. Then the clutch alignment process and all torque settings and everything else unrelated to the kickstarter service becomes obvious.

[@WrongLogic]

@@VoidedWarranty Who are you replying to? I try to encourage people to read the service manuals all the time. I didn't miss anything in this process, I did everything by the book.

[@WrongLogic]

I made this too a while back about the clutch push lever that some people look over: th-cam.com/video/IE5uQrMPOfo/w-d-xo.html

[@VoidedWarranty]

@@WrongLogic yeah that's what I mean. People complaining about missing a step in the video just didnt read the manual.