TDI Swap Cooling System Is Complete!!
ฝัง
- เผยแพร่เมื่อ 16 ส.ค. 2021
- Clamptite tool: amzn.to/3iV6dNo
Stainless wire: amzn.to/2VZFhTQ
Bead Roller: amzn.to/3sqzlPV
1.5" Split Loom amzn.to/3xVfo4w
Heater Core 3/4" 90 Napa PN: 9815
Heater Core 5/8" 90 Napa PN: 9808
Upper Hose Gates PN: 20795
Lower Hose Section Gates PN: 21996
Camera equipment used in the video!
Sony A7II Camera: amzn.to/2yprn1p
GoPro Hero 8 Black: amzn.to/31avsTg
Tripod: amzn.to/35P7oY5
Send me stuff!
PO Box 133
Chattaroy WA 99003 - บันเทิง
Hi Austin it's nice to see your attention to detail on the work you do good job all around......just thought I would mention to make sure there is a spring inside your lower radiator hose it has the potential to collapse when you're cruising around and cause an overheating issue....been there done that.....keep up the good work!!
In reference to the sanitary fittings(tri-clamp ferrule), they are tube dimensions, so the OD is 1" and the ID is typically 0.87" of you have .065" wall fittings. But, It sounds like since use are using stock volkswagon hoses that the dimensions are in metric units, so that very well may be your problem with not being able to find the right fit
Loom looks legit. As long as it doesn’t leak I wouldn’t worry about it
After you get the lift installed a lathe would be very nice to have to make exactly what you want.
I have no clue how people do this stuff without a mill and a lathe. on my swap, it took both. There is no way it could have been done without either.
I am learning. Please keep pumping out the content, Austin.
Looks like it's all going to hold up.
They sell cheap pipe benders at home depot. I would try to bend that aluminum pipe with one of those and then trim to fit. It might not work but I think it would be better than trying to bend it in a vise with heat.
The wire clamp tool is pretty sweet. Nice job.
Thanks 👍
Amazon has 1x1 and 11/4 x 11/4 ICT billet hose barbs. You could cut and weld 2 of them.
Man... I can't wait to hear her start
If you ever decide to sell that truck, do let me know!!!
Excellent work, Austin!
Like the Loom, it looks good.
You’re like the one man 🇺🇸 American version of Wheeler Dealer!
Good job!
Awesome build, I just want to see the fisrt start
I'm surprised no one up North has done a billet replacement for that coolant connection so you don't have to re-use the old hose.
fill that aluminum tube with sand then bend it
Exactly. Also, anneal it before you bend it.
Saludos desde cananea sonora mexico, Austin muy buenos videos
No comprendo !!
Hello greetings from Colombia
Hello from Guatemala
Keep it up
Big fan from Afghanistan
I lost all of my motivation to work on my car after Taliban took over the country
🙁🙁
Have you tried Spokane House of hose for your fittings?
Hello. Great job.
Question! Since you are not keeping the original VW coolant reservoir tank. What you do with the 2 hoses attached to it?
I see that you just blocked the lower hose port. But what about the upper return hose on top of the reservoir?
Thank you.
Saludos des panama
👍👍👍
How did you end up hooking up the coolant temp sensor for the gauges to work?
👏👏👏👏
👍
Fan 100% tacomas!
Still engine is not starting bro this project is playing with our minds
Second... third !!
You should check the TH-cam channel Darkside "Developments". They do great VW mods.
FIRST
You sir , are a very talented individual !!
First 😉