The clutch spring is on wrong and that is why it is not working properly. Look it up on parts diagram and shows you the proper way. Plus that spring has marking saying up.
Ive heard of an Interesting mix of automatic transmission fluid and acetone idk if it will work better than store bought but its definitely worth a try. The mix is 50/50
FYI at the 5 minute 44 second point in the video you make a mistake and put the clutch spring in upside down. Be aware it doesn’t work very well when it’s an upside down.
I have been trying to replace that bearing on my HRR2169VYA mower. The difficulty is removing the outer part of the original ball bearing. It seems to be push fitted and so far impossible to remove. Is there a video with suggestions about removal of the original bearing? Thanks.
@donalburns6548 if i remember correctly i either used the end of the screwdriver and a hammer or a chisel and hammer to remove it. Yes it might take a bit of force
@@donalburns6548put some oil on it and use punch to tap on it by alternating sides to tap it out. Screwdriver could score the bore. Just take your time.
This procedure is incorrect. This will cause premature wear! Exploded parts diagrams are readily available. Print a copy or have your phone/tablet with you. Servicing the blade clutch system is fairly easy.....im not sure how this guy managed to mess it up 😂
Are those "standard philips head" screws or JIS screws? You can " screw" them up with the wrong screwdriver.
The ones that hold the cover on are standard Phillips head screws
The clutch spring is on wrong and that is why it is not working properly. Look it up on parts diagram and shows you the proper way. Plus that spring has marking saying up.
Ok thank you
What honda model is yours? I have HRX217.
HRN216VYA
It is an hrn216vyaa
Nice Simple Video, Thankyou!!!!!!
Your welcome if you have any video suggestions feel free to leave them below
Is there a way to permanently delete it . And not have the lever up top
What lever? The one for the blade clutch? It is a safety feature required by law on all mowers. And removing it can be a safety hazard
@@thehelpfulchannel5 how do i remove it though
Unfortunately i would not know
You make look easy. My belt is tight. Your has no tension. Wonder why?
You have to remove the spring that keeps the self propel belt tight it is near the rear of the mower next to where the pulley sits in the rear
Should of put some grease on shaft to prevent it from getting frozen on.
Thanks for the suggestion
@@thehelpfulchannel5 I have had some where I could not get it off.
Ive heard of an Interesting mix of automatic transmission fluid and acetone idk if it will work better than store bought but its definitely worth a try. The mix is 50/50
FYI at the 5 minute 44 second point in the video you make a mistake and put the clutch spring in upside down. Be aware it doesn’t work very well when it’s an upside down.
Sen varya gercekten süpersin 👍🏼
Thank you please be sure to subscribe to never miss a helpful video
Order a new bearing for the plate you replaced and replace it. You will have a spare plate.
Thanks for the suggestion
I have been trying to replace that bearing on my HRR2169VYA mower. The difficulty is removing the outer part of the original ball bearing. It seems to be push fitted and so far impossible to remove. Is there a video with suggestions about removal of the original bearing? Thanks.
@@donalburns6548only the middle part came out and the race stayed on it?
@donalburns6548 if i remember correctly i either used the end of the screwdriver and a hammer or a chisel and hammer to remove it. Yes it might take a bit of force
@@donalburns6548put some oil on it and use punch to tap on it by alternating sides to tap it out. Screwdriver could score the bore. Just take your time.
You have the clutch spring UPSIDE-DOWN !!! That is why there are scrape marks on the driven disk. Better check your work.
Thanks for the comment
This procedure is incorrect. This will cause premature wear! Exploded parts diagrams are readily available. Print a copy or have your phone/tablet with you. Servicing the blade clutch system is fairly easy.....im not sure how this guy managed to mess it up 😂
Thanks for your input
Well, it was still a very helpful video to show what's involved in this repair.