Once again my problems are a multi-bardwell marathon screening. After a bowl of popcorn and 3 videos I have a night of debugging ahead of me. Thank you JB. Patreon’d yesterday but far too late for the value you give to the universe
Great resource, sir! It took me many hours to discover just a couple of these items. The 'no inputs for auxiliary channels' bit can save pilots a lot of, um, consternation. Thanks!
Thank you for the information, spent 2 hours last night trying to figure out why my 3 position switch on my new boxer only acted as a 2 position, drove me crazy that the higher values were not registering. I ended up resetting the switch mix with the reset feature and started reprogramming the mixer. Some how I must have assigned a value to that switch drop down and limited the range. Your video now confirms that the radio did not have a bug, it was all me being to lazy to read the full documentation. Thank you again for putting my mind at ease and explaining the actual issue.
I had similar issues a year or two back when I bought a Jumper TX. Four of the switches didn't work and I flashed, changed and checked the software and settings before hitting the forums. I was so worried it was the board. Read the forums and they suggested opening and flipping the cables. This worked. At some point they should have used a thicker wire as the wire ribbon is so thin that the latch crimps the cable so thin not all paths make contact.
I have a question about mine. I flew with it a week ago with my plane that has spektrum reciever. Worked fine an all. Well now my TX don't do anything when use rudder. Throttle works an calibration worked when moved stick to. Now I have no rudder input at all
I have my mixer set up using the switch setting you describe as being wrong here but it’s a variant of your all modes on one channel method. The way I am doing it though doesn’t try to cram everything into one channel but groups modes together that don’t need to be activated at the same time with no more than one mode that does. This minimizes the number of ranges needed in BetaFlight. There is a limit to how many you can have in BetaFlight. Think it’s about 22 to 25.
I was trying to figure out why one of my 3-position switches only acted like a 2-position switch. It turned out that under the Hardware screen the 3 pos switch I was trying to get working was set as a 2 pos switch. Another one of the 2 pos switches was set as a 3 pos switch but that didn't impact its functionality. After swapping those settings it is working as it should. I'm thinking that since I upgraded this Taranis X-lite Pro to Edge Tx these settings were set wrong by default. Side note, this radio has been great and by putting an ELRS module in it I think I can get a lot more mileage out of it.
Thank you for: ELRS only outputs 2 positions. The issue now is that my minipix fc with its pre-installed firmware doesn't have the parameter to change the channel for flight modes which is set to channel 5.
Additional info I finally found out when seeing your phone. ELRS supports only 12 channels. I was the whole time wondering why tf my S1/S2/LS/RS didn‘t worked because iNav showed my 17 channels, all switches where configurated right (followed 13, 14, …) and nothing happened. Tried now to set like S2 to ch12 and it worked like a charm. Hopefully some future fellow stumble on this comment when bewing in the same situation.
As usual Bardwell to the rescue. For some reason on this config I had lost my button to flip after crash. I might have a bad button. But the mix was not set on another correctly now. And I might have a dead switch on my Zorro.
it's so hard to find simple answers to simple problems as a noob on edgetx... i just want a 100 to -100 switch. but can only seem to set up momentary switch on button. it's so frustrating. you almost told me how to do it. almost.
What are you trying to do? Turn a momentary switch into a toggle? This isn't really a setup tutorial but if you tell me what you're trying to do, I probably have a video that shows how to do it.
And I noticed that you were talking about; ".....because that's an input icon....." or some such similar, where do you find a listing for what the different icons mean?
@@JoshuaBardwell ummm, well how do you know then? Talked to the dev/manufacturer? I can only intuit the ones that i know are -whichever type of selection thing the icon is next too-. So, outside of some kind of source to learn it from, presumably; you couldn't either. Thanks for the "Welcome". Been here since you were tiny. 😉
In your failsafe tab check the value of your buzzer switch. Usually, you'll want failsafe to activate the buzzer, but if you power up with no radio, it's going to drive you batshit. I'm not sure if that's your problem but...maybe it will help.
Other OPTION❗❗❗❗ GO Into your radio setting and find tbs agent light. Conect your drone/plane Go to setting for your rx that's connect and change 8 Chanel to 12 channel.
I was setting up flight modes on two switches a while back. It was not working and I was getting very odd outputs on the debug keys screen. (Basically, I was seeing switch changes when moving a different physical switch.) I emailed Radiomaster for advice. They suggested removing the main ribbon cable in the Tx, cleaning the contacts (I wiped them with alcohol) and reinstalling it. That fixed it, and it's been fine for over a year. FYI for anyone troubleshooting.
Can you help me out Joshua? I have a radioking opentx transmitter that i use for my velecodrone sim. One day the select mode screen pops up and i no longer is connected with my sim. What do i do when selecting 'USB Joystick (HID)?
I daisy chained the inputs and mixes first time I did it because I thought you had to describe everything at each stage. When you first encounter the tiers of control menus it does seem awfully confusing with excessive redundancy, I guess there is a good reason for it outside of drones, maybe?
It's for setting up advanced features on craft without a computer controller. Crow on a glider is a good example. Crow is used for slowing down and requires the coordinated use of aileron, elevator, and flaps. You could make independent inputs for each control surface with certain restrictions specifically for crow(like adding a little bit of reflex in the wing via raising the ailerons, and adding a bit of down elevator to counteract the flaps), and then mix those together in the mixer so you can assign it to a switch or slider that will control all the inputs at once. All this could be done just with the mixer, but using inputs adds the ability to fine tune the behavior of each of the controls independently.
Once again my problems are a multi-bardwell marathon screening. After a bowl of popcorn and 3 videos I have a night of debugging ahead of me. Thank you JB. Patreon’d yesterday but far too late for the value you give to the universe
Thank you for the support!
ALSO, if you are using CROSSFIRE NANO V3 RX, make sure it is set to 12 channel mode instead of 8CH. This video led me to that. Thanks Bardwell.
Great resource, sir! It took me many hours to discover just a couple of these items. The 'no inputs for auxiliary channels' bit can save pilots a lot of, um, consternation. Thanks!
Thank you for the information, spent 2 hours last night trying to figure out why my 3 position switch on my new boxer only acted as a 2 position, drove me crazy that the higher values were not registering. I ended up resetting the switch mix with the reset feature and started reprogramming the mixer. Some how I must have assigned a value to that switch drop down and limited the range.
Your video now confirms that the radio did not have a bug, it was all me being to lazy to read the full documentation. Thank you again for putting my mind at ease and explaining the actual issue.
Hi, so basically I have pretty much the same problem , but my 3 position switch works on radio but doesn't display on betaflight
Without JB, this hobby would not be the same. Thank you! The explanation of the ELRS hybrid configuration saved me hours of research.
100%
Thanks a bunch for the tutorial, Joshua! 😊
Stay safe there with your family! 🖖😊
Hello Joshua, thanks for this video.. This helped me a lot with the same issue on my radio. God bless u. Keep up the good work. 😊
I had similar issues a year or two back when I bought a Jumper TX. Four of the switches didn't work and I flashed, changed and checked the software and settings before hitting the forums. I was so worried it was the board. Read the forums and they suggested opening and flipping the cables. This worked. At some point they should have used a thicker wire as the wire ribbon is so thin that the latch crimps the cable so thin not all paths make contact.
Thank you man you really save me hours of reserching. For every question i have, you have a video.
I have a question about mine. I flew with it a week ago with my plane that has spektrum reciever. Worked fine an all. Well now my TX don't do anything when use rudder. Throttle works an calibration worked when moved stick to. Now I have no rudder input at all
I have my mixer set up using the switch setting you describe as being wrong here but it’s a variant of your all modes on one channel method. The way I am doing it though doesn’t try to cram everything into one channel but groups modes together that don’t need to be activated at the same time with no more than one mode that does. This minimizes the number of ranges needed in BetaFlight. There is a limit to how many you can have in BetaFlight. Think it’s about 22 to 25.
this video helped me a lot. thanks for posting
The intro😂
I was trying to figure out why one of my 3-position switches only acted like a 2-position switch. It turned out that under the Hardware screen the 3 pos switch I was trying to get working was set as a 2 pos switch. Another one of the 2 pos switches was set as a 3 pos switch but that didn't impact its functionality. After swapping those settings it is working as it should. I'm thinking that since I upgraded this Taranis X-lite Pro to Edge Tx these settings were set wrong by default. Side note, this radio has been great and by putting an ELRS module in it I think I can get a lot more mileage out of it.
Thank you for: ELRS only outputs 2 positions.
The issue now is that my minipix fc with its pre-installed firmware doesn't have the parameter to change the channel for flight modes which is set to channel 5.
Thank you for all the info, my switch works in my controller all the way thru your tutorial but still not seeing SC on BF.
hey josh did you know that you have to Calibrat the dji 03 camera??
Thank You! Yeah I always thought you had to make an input. Just because that's the way it was.
Additional info I finally found out when seeing your phone.
ELRS supports only 12 channels.
I was the whole time wondering why tf my S1/S2/LS/RS didn‘t worked because iNav showed my 17 channels, all switches where configurated right (followed 13, 14, …) and nothing happened.
Tried now to set like S2 to ch12 and it worked like a charm.
Hopefully some future fellow stumble on this comment when bewing in the same situation.
ELRS can do 16 channels if you put it into the one of the "full" packet rates, but the latency is significantly higher.
Amazing :-) CH5 solved, all other problems with channels in INAV solved. THX
Great review and refresher. Thank you.
As usual Bardwell to the rescue. For some reason on this config I had lost my button to flip after crash. I might have a bad button. But the mix was not set on another correctly now. And I might have a dead switch on my Zorro.
Thank you! I learned so much today!
it's so hard to find simple answers to simple problems as a noob on edgetx... i just want a 100 to -100 switch. but can only seem to set up momentary switch on button. it's so frustrating. you almost told me how to do it. almost.
What are you trying to do? Turn a momentary switch into a toggle? This isn't really a setup tutorial but if you tell me what you're trying to do, I probably have a video that shows how to do it.
Thank you for the video xo
Wow, I just posted in betaflight about this yesterday lol. Thank you so much for the help! :p
And I noticed that you were talking about; ".....because that's an input icon....." or some such similar, where do you find a listing for what the different icons mean?
Umm. Yeah. Welcome to FPV. That doesn't exist.
@@JoshuaBardwell ummm, well how do you know then? Talked to the dev/manufacturer? I can only intuit the ones that i know are -whichever type of selection thing the icon is next too-. So, outside of some kind of source to learn it from, presumably; you couldn't either. Thanks for the "Welcome". Been here since you were tiny. 😉
I just figured it out from exposure and inference. You see the same icon on the INPUTS screen. This stuff is really poorly documented, unfortunately.
i have been having a problem with the beepers on my quads, not sure why cuz the switch and buzzer are working so not sure i have the QX7S
In your failsafe tab check the value of your buzzer switch. Usually, you'll want failsafe to activate the buzzer, but if you power up with no radio, it's going to drive you batshit.
I'm not sure if that's your problem but...maybe it will help.
yes, I learned something today. Thanks!
Other OPTION❗❗❗❗
GO Into your radio setting and find tbs agent light.
Conect your drone/plane
Go to setting for your rx that's connect and change 8 Chanel to 12 channel.
BTW, if I'm using ELRS without a flight controller... I could set ch 5 to a value of 2000... Right?
Not if you want to use the ELRS Lua script. It blocks certain settings when the TX is in the armed state
@@malte9999 Oh... I see!
I was setting up flight modes on two switches a while back. It was not working and I was getting very odd outputs on the debug keys screen. (Basically, I was seeing switch changes when moving a different physical switch.) I emailed Radiomaster for advice. They suggested removing the main ribbon cable in the Tx, cleaning the contacts (I wiped them with alcohol) and reinstalling it. That fixed it, and it's been fine for over a year. FYI for anyone troubleshooting.
thank you man! this helped me as well. Almost started looking for a new radio
@bf-man great thanks for letting me know
Can you help me out Joshua? I have a radioking opentx transmitter that i use for my velecodrone sim. One day the select mode screen pops up and i no longer is connected with my sim. What do i do when selecting 'USB Joystick (HID)?
You select USB Joystick (HID) and then what happens?
@JoshuaBardwell it disappears then reappears instantly
Seems like your USB cable or USB port is broken and is disconnecting and reconnecting. That's my best guess.
@@JoshuaBardwell how do i get in enabled if i have an intel core on an apple laptop?
Are you using USB-C to C cable? That can cause problems. Get a USB hub with USB-A ports and/or use a USB OTG adapter.
Brilliant!
I daisy chained the inputs and mixes first time I did it because I thought you had to describe everything at each stage. When you first encounter the tiers of control menus it does seem awfully confusing with excessive redundancy, I guess there is a good reason for it outside of drones, maybe?
It's for setting up advanced features on craft without a computer controller. Crow on a glider is a good example. Crow is used for slowing down and requires the coordinated use of aileron, elevator, and flaps. You could make independent inputs for each control surface with certain restrictions specifically for crow(like adding a little bit of reflex in the wing via raising the ailerons, and adding a bit of down elevator to counteract the flaps), and then mix those together in the mixer so you can assign it to a switch or slider that will control all the inputs at once. All this could be done just with the mixer, but using inputs adds the ability to fine tune the behavior of each of the controls independently.
2:33 you can just swap the plug with an identical switch in the radio to test it instead of buying a new switch just for that probably(hopefully😁)
Thank you i was making that mistake.😊
Thumbs up and good info
Дякую дуже допомогло!
Залюбки, буд ласка!
did you switch back to the tx16s or is this video just pre-recorded?
The Boxer is still my daily. I just used the TX16S because the big screen looks nice on camera.
@@JoshuaBardwell makes sense, keep up the good work, JB :)
So never use Inputs…. That’s new for me. I guess id did a lot of unnecessary work with my models 🤔
Please. Can you help me🙏🏿🙏🏿?
mine dont work because im always dropping my radio
I give up this Nintendo switch will not arm 😢
9/10 times with a jumper its the ribbon cables