Thank you! Without words and translation, but everything is clear! In general, many Russian-speaking users buy such inverters, but sellers do not print manuals in Russian ... This is the only drawback
Espectacular tu conocimiento tigre, solo una consulta el spindle biene con una bomba de agua se puede conectar en el VFD para que encienda al mismo tiempo con el motor spindle...
Hi, thanks for your video. It would be excellent to see part 2 - " how to connect Inverter with matherboard" and configuration for Mach3. Thank You in advance.
Спасибо! Без слов и перевода, но все понятно! Вообще, такие инверторы покупают многие русскоязычные пользователи, но продавцы не печатают мануалы на русском языке ... Это единственный недостаток
hello! which parameter to configure the gain of the inverter? because it did not reach the maximum rpm of 2400 rpm... maximum rpm is around 22300 rpm...
Brilliant video :) Does programming d001=1 and connecting FOR and DCM to a mach3 board is enough to stop the spindle in case of emergency while pushing an E-STOP button? Have a great weekend!
Hello dear The VFD unit is burnt and v changed it. The original VFD is programmed with A11 system. The 1 we changed is with PD00. How can we change it to A11
@@huanyanginverter6516 Hello Do yo have a wiring diagram showing 0-10 v input for speed control and does this inverter have a 0 volt or output showing that the inverter has stopped. Tool change Macro need a inverter at zero output to proceed with tool change. thanks
During configuration for VFD I have problem to find P01, P02. I only got uP0, uP3, uP4, uP5, uP6. Sir, please telling me How to changing these uP code to P code in VFD CNC 6040Z 4 axist. When I tried to reset factory setting error 40 appear. Then unable to get P code again VFD brand is MK100
Hello, hi can i connect hy02d223b Model VFD to mach3 red usb motion card? I need wiring and programming diagram on easy way, everyone looking for this. Please 🙏
@Huanyang inverter . Can you please someone show me how to wired my 2.2Kw HY on my NcStudio ,hundreds of videos for Mack3 but not one for NcStudio please someone ?
@@huanyanginverter6516 Ok ,i'm able to run my 2.2kw spindle manualy by the inverter at max speed of 11250rpm but i dont know how to make my spindle to work by NcStudio on my pc ? ....From my pc when i what to start my spindle and control the speed ,i can't ...It dosen't start ,yes i did short the to VI VR pin the good way and my 4 wired are hook like this ....DCM=GRN....SPL=SP1...MPL=SP2...HPL=SP3.....BUT i am sure its the programation of the inverter i have problem with Exp: PD001=1...PD002=1 ect ect ...Thanks Oh my inverter is a Hy finishing by d223b 3phase
Can you do this same type of video but include reverse . I have the hy 220 volt for 2.2 kw spindle and I got the forward working fine but I cant get the reverse to work can you please help
@@huanyanginverter6516 Ya resolví, el motor es a 110v lo tenia en 220v, muchas gracias. Puedes explicarme como hacer la conexión pero con la controladora NC Studio.
Thank you so much, I was so lost wiering up my VFD. Great Video!
Thank you! Without words and translation, but everything is clear!
In general, many Russian-speaking users buy such inverters, but sellers do not print manuals in Russian ... This is the only drawback
Espectacular tu conocimiento tigre, solo una consulta el spindle biene con una bomba de agua se puede conectar en el VFD para que encienda al mismo tiempo con el motor spindle...
th-cam.com/video/8mbLw3ytnFo/w-d-xo.html
Hi,
thanks for your video. It would be excellent to see part 2 - " how to connect Inverter with matherboard" and configuration for Mach3. Thank You in advance.
If you have any questions, you can ask me
Спасибо! Без слов и перевода, но все понятно!
Вообще, такие инверторы покупают многие русскоязычные пользователи, но продавцы не печатают мануалы на русском языке ... Это единственный недостаток
hello! which parameter to configure the gain of the inverter? because it did not reach the maximum rpm of 2400 rpm... maximum rpm is around 22300 rpm...
hello! Do you have a video on how this inverter is connected to the rnr ecomotion and mach3 board?
th-cam.com/video/8mbLw3ytnFo/w-d-xo.html
th-cam.com/video/UxT2y8b_0SE/w-d-xo.html
Magnífico tutorial. Muchas gracias por su parte.
Saludos
Espero que te ayude. Gracias.
@@huanyanginverter6516 At the end of the video, you need to show a piece of paper all on the video screen. So that you can pause and write off !!!
sr what are the parameters so that when you stop the engine it stops faster. and the parameters for acceleration or starting of the engine. thank you
I don't know what SR is?
Es lo que deberían hacer todos los vendedores chinos con sus productos.
how to connect to mach3 ?
Brilliant video :)
Does programming d001=1 and connecting FOR and DCM to a mach3 board is enough to stop the spindle in case of emergency while pushing an E-STOP button?
Have a great weekend!
Pd046=13
@@huanyanginverter6516 Thank you :)
Have a great weekend
Do you have a wiring diagram or example setup and PD settings if I want to use the VI and ACM. My controller just outputs 0-10v for speed control.
th-cam.com/video/2VXMxxa6lXM/w-d-xo.html
Please could tell, How conect to potentiometer
th-cam.com/video/2VXMxxa6lXM/w-d-xo.html
I get E.Lu.A problem with my inverter. What happen? and what is the solution?
This is low voltage protection
@@huanyanginverter6516 how to solve it?
I've checked the input voltage and its normal.
@@rumahdekorasinusantara send me video xwdnzyp@163.com
Hello dear The VFD unit is burnt and v changed it. The original VFD is programmed with A11 system. The 1 we changed is with PD00. How can we change it to A11
I did not understand what you mean,,, what is A11
Do you have an example For 0-10 Volt control using a Acorn CNc Control. The Acorn outputs 0-10 Thanks
You can use 0-10V to control the speed
It can also output 0-10V
@@huanyanginverter6516 Hello Do yo have a wiring diagram showing 0-10 v input for speed control and does this inverter have a 0 volt or output showing that the inverter has stopped. Tool change Macro need a inverter at zero output to proceed with tool change. thanks
@@gbmachineworks7809 YES，VO terminal, you can output 0
During configuration for VFD I have problem to find P01, P02. I only got uP0, uP3, uP4, uP5, uP6.
Sir, please telling me
How to changing these uP code to P code in VFD CNC 6040Z 4 axist.
When I tried to reset factory setting error 40 appear. Then unable to get P code again
VFD brand is MK100
The vfd product you bought, I don't know, is not huanyang brand
@@huanyanginverter6516 oh I am sorry. The produck vfd MK100 from cnc 6040z
@@FauziIbrahim Sorry, I don't know this machine. If you buy huanyang brand products, I can help you
hi, i got asr 1.0 error and i cant do anything, i cant program. can u tell me what to do? thanks
This is a troublesome matter, the main control chip is not working. xwdnzyp@163.com Take a video and send it to me
Hello, hi can i connect hy02d223b Model VFD to mach3 red usb motion card? I need wiring and programming diagram on easy way, everyone looking for this. Please 🙏
Can be connected. You need to study this video.
@@huanyanginverter6516ok i will try one more time 👍
@Huanyang inverter . Can you please someone show me how to wired my 2.2Kw HY
on my NcStudio ,hundreds of videos for Mack3 but not one for NcStudio please someone ?
th-cam.com/video/APYMDJEsqaM/w-d-xo.html
Please refer to
I still don't understand what you mean. Look, this video, i hope it helps.
th-cam.com/video/2VXMxxa6lXM/w-d-xo.html
@@huanyanginverter6516 Ok ,i'm able to run my 2.2kw spindle manualy by the inverter at max speed of 11250rpm but i dont know how to make my spindle to work by NcStudio on my pc ? ....From my pc when i what to start my spindle and control the speed ,i can't ...It dosen't start ,yes i did short the to VI VR pin the good way and my 4 wired are hook like this ....DCM=GRN....SPL=SP1...MPL=SP2...HPL=SP3.....BUT i am sure its the programation of the inverter i have problem with Exp: PD001=1...PD002=1 ect ect ...Thanks Oh my inverter is a Hy finishing by d223b 3phase
Can you do this same type of video but include reverse . I have the hy 220 volt for 2.2 kw spindle and I got the forward working fine but I cant get the reverse to work can you please help
th-cam.com/video/2VXMxxa6lXM/w-d-xo.html
What is PD 067 for?
This is without any content, it is prepared for adding new functions in the future.
E.oA.A como lo puedo resolver
Aceleración spindle muy lenta
PD014
@@huanyanginverter6516 Ya resolví, el motor es a 110v lo tenia en 220v, muchas gracias. Puedes explicarme como hacer la conexión pero con la controladora NC Studio.
Excelente
ok
At the end of the video, you need to show a piece of paper all on the video screen. So that you can pause and write off !!!
I don't understand what you mean.
it doesn't show how to connect it to Mach3...
E.oA.A como lo puedo resolver
Disconnect the motor and try it out