I bought the 220VAC 1500W VFD & spindle motor for my DIY CNC router. The manual was pretty good,(****), and support was fair. I had a problem getting the multi speed feature working, and the vendor just stopped answering my emails. I figured it out anyway and forwarded the answer to them. overall 4 stars of 5. Vendor says braking does not work for my unit, I just wonder if they know the product well enough.
Hello, I bought the same model complete spindlle kit and 2.2kw water cooling inverter. but I'm having problems with loss of torque at low rpm Is there any way to adjust this so as not to lose torque? Thanks
@@huanyanginverter6516 The rpm values on the Mach3 are not the same as those on the frequency inverter. The values are always fluctuating, more or less for example, if you put 16000 rpm on the Mach3, in winter it appears 16345 or 15857 +/- It never reaches 16000 rpm correctly. someone help please.
@@clidersemedo8013 "For the VFD, an input of 10V will reach the maximum frequency. The frequency is directly related to the 10V input voltage. Slight fluctuations in the 10V voltage can affect the frequency. You can use parameter Pd071 to delay frequency fluctuations."
Hi there! I have bought a Huanyang spindle and the same VFD as in this video. I have wired it as you U=1, V=2, W=3. But my spindle spins backwards (in counterclockwise direction). What is wrong?
I have the (HY02D211B)110v vfd and 110v 2.2kw spindle, 8.5 amp. What are settings for PD006, PD007,PD009,PD010,PD011, PD041,PD120PD142,PD174. Thanks, Joe
@@huanyanginverter6516 .my question is in my 110v vfd ( and 2.2kw 110v spindle) the settings for pd 173, 174, and 176 do not stay changed . Keeps resorting back to 220, 11 amps and "0"....I need 110v, 20 amps, and "1" for 60hz. Maybe these settings don't matter, IDK... all other parameters retain their changes that I made. My vfd does say 20amps on label, although when spindle up to 24000 rpm, amps read 2.0 on display
I have this package from you, it was working well, between bit changes it will not work. When pressing "RUN", VFD shows spin up to 7800 rpm, the spindle makes noise however the bit does not spin. I can move the bit freely by hand, spindle seems to be making noise. Once it hits 7800 RPM, "EOCA" appears on the VFD and spindle doesn't make noise anymore. Please help!
i have a GT-4R0G-2 trying to run 3.2kw spindle. Got the spindle to auto tune but can not get it run via keypad and pot on front of inverter. It is slightly different than this model. any help would be appreciated. then i have to get it working with Mach 4
What's the operating voltage of this VFD shown on this video? Thus it comes with the braking resistor? Also thus the 220V model VFD will also work using step-up transformer if 110V was only available power source?
Hola, tengo un problema, en sentido FOR me va todo bien pero cuando cambio a REV empieza lento y se para. Porque puede ser? En FOR me gira en sentido antihorario y me gustaria que girara en sentido horario
Good video! That sucks we don't have an amazon account, we get all the cnc parts from AliExpress stores. I think we already ordered a spindle from you...
I bought the 220VAC 1500W VFD & spindle motor for my DIY CNC router. The manual was pretty good,(****), and support was fair. I had a problem getting the multi speed feature working, and the vendor just stopped answering my emails. I figured it out anyway and forwarded the answer to them. overall 4 stars of 5. Vendor says braking does not work for my unit, I just wonder if they know the product well enough.
th-cam.com/video/UxT2y8b_0SE/w-d-xo.html
Thank you broather huanyang🙏🙏🙏👍👍👍👍👍👍👍👍👍
Well done sir very useful
Alles schön und gut,aber mit welchem Ausgang kann ich ein Relais schalten und welche Parameter müssen dafür wie eingestellt werden.
Pd052 parameter
Was ist das für eine Antwort. Welche Ausgänge werden dann dafür verwendet. Man sollte das schon ausführlicher beschreiben
sr what are the parameters so that when you stop the engine it stops faster. and the parameters for acceleration or starting of the engine. thank you
Your sketching is too simple, I don't understand what you mean.. What is SR?
Hello, I bought the same model complete spindlle kit and 2.2kw water cooling inverter. but I'm having problems with loss of torque at low rpm Is there any way to adjust this so as not to lose torque? Thanks
Low RPM? How low is it? High-speed motors cannot operate at low speeds. It will burn out the motor
@@huanyanginverter6516we are talking about 4000 rpm
even at 4000 rpm it can burn?
@@clidersemedo8013 Your motor is 24000 rpm. You are dropping to 4000/per minute, which is not acceptable
@@huanyanginverter6516 The rpm values on the Mach3 are not the same as those on the frequency inverter. The values are always fluctuating, more or less for example, if you put 16000 rpm on the Mach3, in winter it appears 16345 or 15857 +/- It never reaches 16000 rpm correctly. someone help please.
@@clidersemedo8013 "For the VFD, an input of 10V will reach the maximum frequency. The frequency is directly related to the 10V input voltage. Slight fluctuations in the 10V voltage can affect the frequency. You can use parameter Pd071 to delay frequency fluctuations."
is your settings based on the 2.2Kw huanyang spindle ?
yes
Hi there! I have bought a Huanyang spindle and the same VFD as in this video. I have wired it as you U=1, V=2, W=3. But my spindle spins backwards (in counterclockwise direction). What is wrong?
U=2 V=1 W=3 It's normal
@@huanyanginverter6516 Thank you!
@@huanyanginverter6516 But probably I can swap any two of those, is it true?
U=2 V=1 W=3
What are the settings for the UK 230 Volts AC @ 50Hz please?
I have the (HY02D211B)110v vfd and 110v 2.2kw spindle, 8.5 amp. What are settings for PD006, PD007,PD009,PD010,PD011, PD041,PD120PD142,PD174.
Thanks, Joe
None of these parameters need to be changed. You just need to change the frequency.
@@huanyanginverter6516 .my question is in my 110v vfd ( and 2.2kw 110v spindle) the settings for pd 173, 174, and 176 do not stay changed . Keeps resorting back to 220, 11 amps and "0"....I need 110v, 20 amps, and "1" for 60hz. Maybe these settings don't matter, IDK... all other parameters retain their changes that I made. My vfd does say 20amps on label, although when spindle up to 24000 rpm, amps read 2.0 on display
@@jstef4136 20A is a limit number... Normal operation is far lower than 20A
@@huanyanginverter6516 but what about volts and Hz? do I have to reset these everytime I turn it on? I need 110v and 60 hz.
@@jstef4136 Input voltage does not need to be set.. The output rate must be set to the same frequency as the motor. This is very important.
I have this vfd and 2.2kw spindle.. Does the cable need to be sheilded
You don't need it.
@@huanyanginverter6516 so just 4 core so.. Will 18g be ok
Are these settings for for the usa? Our grid operates on 60hz and these are 400hz settings.
Can be used in the U.S. 60HZ
Where do I install my output ground going to my motor? My machine has 4 wires, it is not a spindle.
The UVW is connected to the motor, and that's it
Good morning
My huanyang HY02D223B spindle continues to turn at 200rpm when I enter the M5 command can you help me?
I have this package from you, it was working well, between bit changes it will not work. When pressing "RUN", VFD shows spin up to 7800 rpm, the spindle makes noise however the bit does not spin. I can move the bit freely by hand, spindle seems to be making noise. Once it hits 7800 RPM, "EOCA" appears on the VFD and spindle doesn't make noise anymore. Please help!
Most likely it is UVW, missing a phase
How about mini-VFD review next time?
Hi
Is there a way to program the motor frequency higher than 400hz. I have a motor that requires 1100hz @ 230v
No way, only up to 400hz
Can you help me. My spindle not run. (Erro Lu5)
I use huanyang VFD 1.5kw 220v
This is a hint of low voltage
Process video shot and sent to me
i have a GT-4R0G-2 trying to run 3.2kw spindle. Got the spindle to auto tune but can not get it run via keypad and pot on front of inverter. It is slightly different than this model. any help would be appreciated. then i have to get it working with Mach 4
th-cam.com/video/KD_NrfL7ZZs/w-d-xo.html
th-cam.com/video/eeiIWLAttHM/w-d-xo.html
Nice! But there's need some help. My spindle is not working when frequency is more than 50 htz. And Factory reset in my case was 01 instead of 08
A few years ago the product was reset to 01, and the current product reset was 08.
I guess other parameters were different. So give me parameters few years from now. Thank you.
I can't understand your meaning. Pls send me a video about your Problem. My E-mail is service@hy-electrical.com.
I mean factory reset was 01 instead of 08. And maybe other parameters were different too. Such as PD05 (max frq) etc.
Earlier versions restored to factory settings were set to 01 and are now set to 08 to restore factory settings.
can the run button be disabled so i can run stat an stop from my shark hd controler
Buenas tardes tengo un controlador ddcsv3 me podrían brindar asesoría para conectarlo correctamente con el inversor gracias.
th-cam.com/video/8mbLw3ytnFo/w-d-xo.html
th-cam.com/video/UxT2y8b_0SE/w-d-xo.html
What's the operating voltage of this VFD shown on this video? Thus it comes with the braking resistor? Also thus the 220V model VFD will also work using step-up transformer if 110V was only available power source?
The video shows 220V power. if you use 110V, the spindle motor also must be 110V.And It can stop in 5 seconds without adding brake resistor.
Can I use a step-up transformer from 110V to 220V if 110V source was not available?
You buy a 110V motor and VFD
I had 3000W step-up transformer to be use with 220V VFD version that’s why I am asking. Will it work?
has an effect. . . . But the load can't be too heavy.@@ferdieedquiban9047
any info using speed control work with mach3 ?
th-cam.com/video/UxT2y8b_0SE/w-d-xo.html
Hola, tengo un problema, en sentido FOR me va todo bien pero cuando cambio a REV empieza lento y se para. Porque puede ser? En FOR me gira en sentido antihorario y me gustaria que girara en sentido horario
UVW, changing to UWV can solve your problem
@@huanyanginverter6516 Gracias, ahora va bien
@@pharys10 Ok
Can you help me. My spindle not run.
I use huanyang VFD 1.5kw
ok，skype:China-hy. Messenger:service@hy-electrical.com
we can help you also...
Hello
Good video! That sucks we don't have an amazon account, we get all the cnc parts from AliExpress stores. I think we already ordered a spindle from you...
And don't put the links when you commenting other channels videos, youtube delete them automatically
Thanks for your interest.I will post more and more videos. You can order from AliExpress.
Already ordered! Check out video-reviews on my channel.
Do you have something to review on our channels? We can review any CNC parts either in Russian or English.
Could you please give me a link on your AliExpress official store?
ឣរគុណ
This I tried and smells came from controller, be aware; I have spent weeks trying to get it to work and there is no tech support
whatsAPP：+86 18072595511 Be sure to contact me, do not continue to test. There must be something wrong with the parameters.
SKYPE: China-hy
Wechat: China-VFD
Huanyang inverter I am having same trouble. Been three days and no response from company.