This is by far the best how to video I have found on copper tubing cutting. I always have a problem with the little cutter not staying in the grove and making a "candy cane".
My dad had one of those cast iron cutters....I got to use it a few times when he had me on the job site.... I'll tell you when the pipe pops you'll know it and as a skinny kid it took all my weight to get the pipe cut....
me in trade school nervous asf right now since nyc doesnt use plastic pipes and we gotta use cast iron, im still struggling to cut them for the right measurements , wish me luck yall :/ i really wanna be a plumber
How about brass tube that isn't round but oblong or "D" shaped? Like used in an adjustable hand shower bar that needs to be cut shorter because they plumbed the fixture to where the mount is mounted right in the middle of a mosaic design.
I've heard you can use any kind of oil as a cutting oil for threading pipe. Motor oil and soap in place of a cutting oil, even a spray lubricant. If I went and bought a small can of cutting oil for 13.00 when I could of just used WD40, did I just get had?
If it is chromed brass like you see in flushometers or exposed drain pipe I like the Ridgid #30 tubing cutters. If there isn't enough space you are looking at a hacksaw or reciprocating saw.
I was hoping to see how to cut that thin 1 1/4" chrome drain pipe under a bathroom sink. The one that goes straight down from the drain in the basin to the p-trap.
If it is chrome plated brass, use a chop saw (miter saw) which has a good carbide blade. Check with a magnet to make sure it is not steel. Wear goggles! NOT just safety glasses. Cut like its cutting a hard 2x4 at half pressure.
the one i need to do is cut the pipe below the floor level at 4:00 in this video. but it not PVC it is metal pips that are below the cement floor level out side thy use to be the support polls from the old patio. but now i need to pull out about 6 inches of pip, so i can full it up with cement Not concrete but cement. to match the smooth cement floor. But my problem is that i am using a drill that not very fast spinning. And can not afford a new drill, and battery life is sh*t. i think it will not spin fast enough to cut any thing. But the blade is new it is some kind of black color blade. And i can not use disc grinder because i need to be cutting 6 inch deep and i also do not have a disc grinder
I wonder if they ever wonder how much money they save us by teaching us how to do home projects that otherwise would cost us hundreds to hire out. Thank you!
Where is your PPE guys? 😧 I was cringing when you were cutting that pipe with a hacksaw so fast and so near to your hand. You would be fired at my job. Safety first!
Is that last one really how you're suppose to cut the big pipe? It didn't even cut it, it BROKE it. Then what? Are you supposed to thread it all jagged and broken like that?
I like videos that show the proper tools for the job. This one covered all the average pipes.
This is by far the best how to video I have found on copper tubing cutting. I always have a problem with the little cutter not staying in the grove and making a "candy cane".
Just once in my life I need to use one of those cast iron cutters.
Raw Bacon they are really fun to use but scary when you’re just waiting for it to snap 😂
Got my answer. Thank you guys. You are the best. I’ve watched for many many years.
Cast iron part was the best.
Yes it was, now I know something new
NineduceXII "take that grampie!" "....why does he keep mentioning his grandfather..." "LOOK AT ME NOW GRANDPA! OH WAIT, YOU CANT, CUZ YOU'RE DEAD!"
his grandpa is a scumbag
Yes. I just cut cast iron with my sawzall. Thank god for new technology!
@@b.michaelbrown1117 what size was pipe how long did it take and what kind of blade
Can’t tell y’all how many times I’ve cut cast iron piping of all sizes with a sawzall and thick metal carbide blade, pretty straight cuts too 👍🏼
Yeah every time I've used/seen a snap cutter used it leaves jagged edges
@@VanillaHorror not to mention that cutter is ridiculously expensive
I was waiting for the cast iron part 🤩
All very informative...but the cast iron cutter ? WOW...what a BEAST.
Just use a Sawzall with the right blade
My dad had one of those cast iron cutters....I got to use it a few times when he had me on the job site.... I'll tell you when the pipe pops you'll know it and as a skinny kid it took all my weight to get the pipe cut....
My god, always brilliant videos. Love it! Love all your videos!!!
Diamond blade on my angle grinder worked excellently on the cast iron stack in my brother's house
going "out of round" is caused by tightening too much, good point...thanks...
they have new hacksaw / recip saw blades to cut ductile and cast iron now as well.
I really can't explain the sheer excitement in using one of those cast iron cutters because I've never used one.
The ratchet cutters work great on new PVC pipe. Old pipe can shatter. It is better to use a reciprocating saw or PVC saw on those.
I.Like this Old House
Too funny, “take that, Grammy”. Thank you guys.
That cast iron cutter was a monster!
An interesting side use for that tool is rock collectors use them to break geodes in half.
Take that Gramps, love it
Take that, Grampy!
I liked the ridget with the ratchet. I wonder if that cuts conduit?
what can be used for galvanized??
Nice job
Thank you.
Do I need to cut any pipes? No. Did i watch this whole video? Yes I did!😅
Thanks
What’s the name or brand that is self tightening that use to be available in Europe now is available in USA?
AutoCut by General Pipe Cleaners
www.amazon.com/dp/B0012QGUSM/ref=cm_sw_r_cp_api_i_b4DzEbXDEWA9G
I waited for the last tool.
me in trade school nervous asf right now since nyc doesnt use plastic pipes and we gotta use cast iron, im still struggling to cut them for the right measurements , wish me luck yall :/ i really wanna be a plumber
How about brass tube that isn't round but oblong or "D" shaped? Like used in an adjustable hand shower bar that needs to be cut shorter because they plumbed the fixture to where the mount is mounted right in the middle of a mosaic design.
Abrasive disc blade in a Dremel.
I've heard you can use any kind of oil as a cutting oil for threading pipe. Motor oil and soap in place of a cutting oil, even a spray lubricant. If I went and bought a small can of cutting oil for 13.00 when I could of just used WD40, did I just get had?
You would use cutting oil if you had a lot of pipe/steel to cut. It has a high temp to resist burning/smoke.
Best tool to cut chrome pipe?
If it is chromed brass like you see in flushometers or exposed drain pipe I like the Ridgid #30 tubing cutters. If there isn't enough space you are looking at a hacksaw or reciprocating saw.
I was hoping to see how to cut that thin 1 1/4" chrome drain pipe under a bathroom sink. The one that goes straight down from the drain in the basin to the p-trap.
Copper tubing cutters
If it is chrome plated brass, use a chop saw (miter saw) which has a good carbide blade. Check with a magnet to make sure it is not steel. Wear goggles! NOT just safety glasses. Cut like its cutting a hard 2x4 at half pressure.
Ridgid #30 tubing cutters if there is space.
A pro press with a cast iron snapping attachment makes it quick easy work, But it’s costly.
I watched this just for the fun of watching a cast iron pipe cutter.
I watched it for the fun of the pex cutter.
@@nastyhvacr I can understand that. But nothing compares with a cast iron pipe cutter or pouring lead in a bell and thimble joint.
Only came to read comments by experts claiming to know far more about pipe cutters than Richard.
the one i need to do is cut the pipe below the floor level at 4:00 in this video.
but it not PVC it is metal pips that are below the cement floor level out side thy use to be the support polls from the old patio.
but now i need to pull out about 6 inches of pip, so i can full it up with cement Not concrete but cement.
to match the smooth cement floor.
But my problem is that i am using a drill that not very fast spinning.
And can not afford a new drill, and battery life is sh*t. i think it will not spin fast enough to cut any thing.
But the blade is new it is some kind of black color blade.
And i can not use disc grinder because i need to be cutting 6 inch deep and i also do not have a disc grinder
You missed one of THE most common pipes! Chrome plated brass supply lines for a sink or for a toilet.
Same cutters as for copper tubing.
In my mind, I said, "Like Butta" before he did. 🙃
I have to use a butter knife, nail file, box cutter and sometimes a soldering iron to cut my PVC pipe. It's only for Nerf mods.
Can't do the job without the right toys.....uh tools.
I wonder if they ever wonder how much money they save us by teaching us how to do home projects that otherwise would cost us hundreds to hire out. Thank you!
Omg why’s his hand so close to the hacksaw 😱 other than that I learned a lot from the video thanks
3:54 Like Butta!!!
Is there any other way to cut cast pipes?
YES! Carbide blade for reciprocating saw. Costs about $12 on Amazon. Who can spend $2,000 on that monster iron pipe cutter?!
Europe: we have some nice cutters, US: pshhhh..
What about ABS pipe?
Same as PVC
where the hell did he get that crescent wrench ratchet tool for the junior tube cutter@!@!! I need it!
www.amazon.com/RIDGID-32573-Quarters-AUTOFEED-Ratchet/dp/B003IEPCXA/ref=pd_sbs_469_9?_encoding=UTF8&pd_rd_i=B003IEPCXA&pd_rd_r=0Q059EFANCPVNBDSFXPT&pd_rd_w=jfcW3&pd_rd_wg=mnvoC&psc=1&refRID=0Q059EFANCPVNBDSFXPT
how much do these cost?
That's not only way to cut cast iron pipe. A Sawzall with metal cutting blade cuts much cleaner.
Armour Line RP77171 Internal Plastic Pipe Cutter
thanks tony soprano
LIKE BUTTAH
anthony aleman like BUTTAH and no burs
anthony aleman
should not the description say first tubing cutter is for copper
Why was he in a hurry tomake a cut-I was interested in seeing how much clearance each tool has.
Why did i look this up 😂
It looked like he was expecting a bomb to explode when he was cutting the cast iron
Drama for the safety police.
Take that grampy's
4:42
This is a standard TOOBING cutter
Only way to cut cast Diablo "am i a joke to you"
“Take that granpy”
Where is your PPE guys? 😧 I was cringing when you were cutting that pipe with a hacksaw so fast and so near to your hand. You would be fired at my job. Safety first!
cutting steel w sawzall is ballsy if its gas inside
Purge first it's the law in UK
The auto cuts are the only way to go on copper!
Whhaaatt I’ve got 4 different ways to cut cast on the truck. Snapcaster aren’t that great for repipe sin crawlspaces
Came here for unnecessary complaints about plumber's putty.
I'm disappointed in you, TH-cam.
Is that last one really how you're suppose to cut the big pipe? It didn't even cut it, it BROKE it. Then what? Are you supposed to thread it all jagged and broken like that?
You don't thread cast iron pipe moron
you don't thread that type of cast iron, you use no hub couplings.
All pipe cutters wander.
Whatatay T not my m12 copper cutter
Only if you are a halfwit
I seriously hate that he says it’s called an “imp” it’s not it’s basically a mini pipe cutter an imp is just what u call it Boston George
Imagine carrying that heavy tool to cut cast iron and then seeing someone else cut it with a Diablo blade with ease lol
En español por favor.....
Vidal Vega or go back to Mexico
bludika go back to Europe or whatever country you migrate
Ö
Left out one other way to cut pipe,.... hire a professional! Take that grampy!
3:48 did he just said the n word?
Jon Hipolito he said nipper, I also said whaaaat for a split second lol
It's like butta
No because the tool would not work
You live in the USA learn English