Eductor part is wrong mate.. illustration should be 1 from liquid goes to eductor, 1 line from buttom of the barrel or evaporator and 1 line back to suction line.. this kind of oil management is almost the same of rtac unit. Oil from buttom barrel then back to compressor
Thank you, after I finished it and released it I realized I made a mistake on that part. What I will have to do is make a separate correction video doing a better job on that.
@@HVACTIME yvaa has some changes depends on coil either copper coil or micro channel. Copper condenser coil the drain valve control by liquid level sensor at evaporator whereas with micro channel coil they dont have liquid level sensor at evaporator. I have few yvaa unit that i maintain here in the island
Economizer opens based on comp frequency. Our YVAA now does not have check valves in the econ pipe, because our newer software allows for Economizer backflow control.
Ran into a yciv today for the first time. I'm used to working on rack refrigeration, needless to say I was all kinds of turned around. This video made it all so clear to me now. I'll be working on it again later this week... Atleast I'm armed with some knowledge now. Thanks a ton! 🍻
Love the video! Everything was perfectly explained but I would like to add, there is not a “DRAIN VALVE” on the flash tank leaving line to evap. Now there is a shut off but not an eev device.
I hope to one day understand and be proficient at troubleshooting equipment like this. This type of equipment is what i get up and get going for. I love this trade
You posted this at a perfect time for me ! I just finished going over a few yvaa’s with my journeyman this past couple days. Love the videos keep it up!
Thank you very sir, really fantastic explanation, could you please provide more theatrical explanation , how FD working and collect oil from the cycle.
You know I'm glad you said something, I made a mistake on my YVAA rundown. There is not a drain valve after the flash tank. It uses the "condenser drain valve" aka the feed valve only. I will need to make that correction some how.
I have same unit YCIV micro channel cond coil.im facing problem in drain valve not giving the exact position when I put manually put it to 100% open and 0% closed,when it run it having alarm low suction limiting and unusual sound of the compressor.i suspect the stipper motor module so I tried to swap from other unit but still problem occur.unit shutdown low suction pressure. Any advice
![HIWWHEE | OHM [Official MV]](http://i.ytimg.com/vi/OJJLtTLqLag/mqdefault.jpg)
Eductor part is wrong mate.. illustration should be 1 from liquid goes to eductor, 1 line from buttom of the barrel or evaporator and 1 line back to suction line.. this kind of oil management is almost the same of rtac unit. Oil from buttom barrel then back to compressor
Thank you, after I finished it and released it I realized I made a mistake on that part. What I will have to do is make a separate correction video doing a better job on that.
@@HVACTIME yvaa has some changes depends on coil either copper coil or micro channel. Copper condenser coil the drain valve control by liquid level sensor at evaporator whereas with micro channel coil they dont have liquid level sensor at evaporator. I have few yvaa unit that i maintain here in the island
All of mine have micro channel.
Economizer opens based on comp frequency. Our YVAA now does not have check valves in the econ pipe, because our newer software allows for Economizer backflow control.
@FILIPINO WONDER'S yvaa sir?
after watching this video, my basic dx chiller cycle clear , thanks a lot HVAC time
I made a mistake on my YVAA rundown. There is not a drain valve after the flash tank. It uses the "condenser drain valve" aka the feed valve only.
I was going crazy looking for that thing lol. Glad I came to comments
Lol my bad
Ran into a yciv today for the first time. I'm used to working on rack refrigeration, needless to say I was all kinds of turned around. This video made it all so clear to me now. I'll be working on it again later this week... Atleast I'm armed with some knowledge now. Thanks a ton! 🍻
Love the video! Everything was perfectly explained but I would like to add, there is not a “DRAIN VALVE” on the flash tank leaving line to evap. Now there is a shut off but not an eev device.
I hope to one day understand and be proficient at troubleshooting equipment like this. This type of equipment is what i get up and get going for. I love this trade
You posted this at a perfect time for me ! I just finished going over a few yvaa’s with my journeyman this past couple days. Love the videos keep it up!
I love your videos. Great info!!
Bro thank you so much man. I just got a job as a facilities engineer and this stuff is hard for me to fully grasp. Thank you for breaking this down.
Thank you very sir, really fantastic explanation, could you please provide more theatrical explanation , how FD working and collect oil from the cycle.
Thank you for these videos. HVAC Gold.
need a separate video on edector system
Great video the chiller I have seen Model YVAA fix orifice instead drain valve (EEX)
You know I'm glad you said something, I made a mistake on my YVAA rundown. There is not a drain valve after the flash tank. It uses the "condenser drain valve" aka the feed valve only. I will need to make that correction some how.
my best dear techar for my life great vidio for me.
very useful information, thank you very much.
Thanks for really informative video.
It would be awesome to see a video on a daikin screw. In particular how the capacity slides valves work in detail.
it may be superheat which controls the slide valve which is typically what loads a screw compressor
Very useful information
after watching all the chiller videos on you tube, you have found where the BEAR SHIT IN THE WOODS...thank you. great VIDEO.
great explanation
Amazing video man
Pls. Look into enhancing the video lighting. Thanks
Awesome vedio :) i think the stupid thing in this system it dont have feed back in valve position
Great Video!
Great info thank you 👍
Most helpfull ,,, Thanks very muck
hi. do you have a video on the channel on how to properly replace the oil on the York YVAA chiller?
good job
Good stuff
How to remove suction line from the barrack or cooler can u explained me pls
Amazing video brother, kindly explain same to Trained cvhe or cvhf water cooled chiller . Thanks
Coming Soon!
@@HVACTIME thanks
How to change York chiller reciprocating oil heater old compressor
Nice video brother...My VSD assembly in YVAA got burned. What could be the reason
Can you change the EXV motor on these chillers without removing the Freon
Hey, great video thanks for taking the time to do them.
Question. if I'm understanding right the drain valve is the metering device?
At its core yes, It is the final flash point that is controlling evap superheat. But the feed valve also plays a critical role in that as well.
@@HVACTIME I understand now. Thanks for the quick response!
Hi please there is leaked in evaporater. How can I repair it only in Cerkit 1 thanks
Sir chiller displays show vsd communication failure fault what is the problem
Great video! Where did get training on these? I know York doesn't offer training to none JCI technicians.
School of hard knocks and manuals lol
Pls how do oil charges this chiller pls make explain sir
Sir how to change oil in YVAA fladed chiller
Can you explain exactly what the economizer valve does? Is it cooling the compressor or reducing compression ratio?
Its pulling flash gas to reduce pressure on the flash tank.
That was what i was thinking as well
I have same unit YCIV micro channel cond coil.im facing problem in drain valve not giving the exact position when I put manually put it to 100% open and 0% closed,when it run it having alarm low suction limiting and unusual sound of the compressor.i suspect the stipper motor module so I tried to swap from other unit but still problem occur.unit shutdown low suction pressure. Any advice
Extremely common for the exv gears to where out and stick causing it to get out of calibration. Recommend replacing exv.
Sir i have carrier chiller with water cooled condenser is it possible to convert to air cooled condenser.
I would heavily advise not to try
Have you had a oil separator on a YCAV start to plug up?
No haven't ran into that one
Wouldnt happen to have a York YCUL080 air cooled service manual you could email could you?
where the supper heat sensor installed?
There is a thermistor on the suction pipe.
@@HVACTIME thanks
Hello brother how to reset alarm on this chiller
You do it through the system switches menu
Clark Jeffrey Lopez Donna Hernandez Edward
Holden, the beginning is too dark, we can't really see components.
Sorry did the best I could at the time.
@@HVACTIME I know brother
How to drain the oil for YVAA? please for your advise.
At the oil service valve
Sir need help
Picture not so clear
whats not clear?
@@HVACTIMEVideo not Sunny