Whirlpool Cabrio Washer & Dryer Diagnostic Mode & Read Error Code List - How to
ฝัง
- เผยแพร่เมื่อ 30 ก.ค. 2024
- Not every Whirlpool Cabrio washer or dryer is the same when it comes to putting them into diagnostics mode, but if your unit looks like this, then this is the video to watch on how to put it into diagnostics mode, as well as what options are available to you on tests to get your washer back up and running.
DISCLOSURE: This post may contain affiliate links, meaning when you click the links and make a purchase, we receive a commission.
Affiliate Link & Earnings Disclosure: bit.ly/3oXeu3B
If you need to buy an appliance part to fix your washer, make sure to use Appliance Part Pro's model lookup system to get the EXACT part you need, to ensure it works - plus, you can return it if it doesn't fix your issue: bit.ly/3pVxWyX
Tools I use in all videos can be found at my Amazon Idea Page: www.amazon.com/shop/bensappli...
Did this video help you out? Send me a tip, and help me make more Appliance Repair videos for people to watch for free!
PayPal: paypal.me/BensappliancesYT?lo...
CashApp: $BenjaminSchlichter - แนวปฏิบัติและการใช้ชีวิต
I had one of the cabrio washers not my favorite. It had a bad lid switch, luckily found it used. Left a little bit of a profit at the end was glad to get rid of it.
Nice!
This works for the dryer but not for the same model cabrio platinum washer. I had to long press (3 second) one of the buttons 3-4 times that were not power or start to enter diagnostics. Thank you for this video though. It Helped me find the one I needed
Do you know what it means when the washer doesn't respond to the strategy you used? I think we have the same washer but mine doesn't display any codes when I follow the directions you used.
Same, but it was my Cabrio dryer that was accessed that way so I’m glad I saw your comment, thank you 🙏🏼
Now I need to figure how to toggle thru since I didn’t use the 3 buttons to enter diagnostics mode…
you have a great teaching style
Thanks!
Hi, I have this same dryer except for a few drying cycles, question..do i always have to turn it off just to change drying cycles..times. ?
Ben
I have this exact gas dryer.
It will not get hot when using the eco cycles.
On quick dry it barely gets warm...
Vents are all clean....
What might be causing this?
Thank you ,found out through your video, my code is f 4. E3 ,so it's restricted air flow, probably clogged with lint somewhere, thank you,Great video !!
About two years ago we had a restricted air flow issue. We found out that a mockingbird had built a nest about two feet inside the the outdoor exhaust vent. We cleared the nest and installed a three louvre vent door that is bird proof. Haven't had any problem since.
Thank you! This helped me solve the “check vent” red light!
Wait, what was the issue with the check vent? He didn’t discuss that specifically
It will turn on randomly even if ur vent is clean/fine@@TheMochaangel
I subscribed and will let you know i have an electric model let you know how it turns out. Thanks. I'm a 3rd Generation Plumber / Heater a.k.a. tin-knocker / A.C. Tech. / Electrician and Appliance repair man / a little of every thing type of guy been at it for well let just say helped my father since the mid 70's yes old lol. I never dealt with this model before till my wife made me buy one lol , thanks again for the info.
I have a cabrio platinum washer and I did what you did on the video I can't get into diagnostic mode. I keep getting an oL (overload) with nothing in it. Any other ideas?
I liked and subscribed. Thank you for your content.
Hi sir how are you the mettell insert on my nub broke out do you know how to put it back in on a whirlpool Cabro platinum washer please and thank you
I have error code F31 but my tech sheet is missing from under the panel, have any idea what that code is?
I have a gas Cabrio dryer. grateful for your assistance learning the code F28...replaced both sensor bars, to no avail. The machine will let you power up to dry clotehes, sensing comes up -- depletes to 0 minutes and does nothing in-between but count down the timer ?? Any ideas?
There's usually a small sensor harness inside the unit that connects the wire harness to the sensor bars. They use some capacitors/resistors that can go bad from time to time. I'd check that out to see.
Hello, I have F0 E3 and FO E4 error codes but I do not have the manual. Could you tell me what those 2 codes mean? I really appreciate your help if you could answer me. Thanks
My dryer suddenly stopped and now it just says sensing? What does that mean
Great video!!!
If you can't enter diagnostics mode that way, try holding "Temp" button for 2 seconds then release for 2 seconds × 3.
Thank you for your videos last week I changed hub because was not spinning and after that worked well today I got the same error code what should I do please help
Was the new washer hub gear plastic? There is an upgrade to a revised metal hub kit on some Cabrio models. Cost more but last longer. If you have that model and chose the plastic one instead of the metal one. Then it may be the shaft splines were to damaged due to rust , age, and poor design . Which would quickly wear out that new plastic hub. Your problem would return. W10324651 is the new revised hub kit to replace W10528947. There are several Maytag and whirlpool washers that this type hub revision will work on. Your comment is 2 yrs old so I'm obviously to late for you but perhaps others will see and benefit. 😅
My Dryer going into Diagnostic says ( 88 ) which you says it means everything is normal, but my dryer motor does not turn the drum there is no noise that anything is going on down there BUT the heating element DOES work. So, does it mean then that the motor itself just isnt working ??
I have this model dryer, it powers on but when I hit the start button it just beeps once and the dryer doesn’t start. Please help
I change the side that the door opens on and I get the same thing it comes on but when I hit start it just beeps
Thanks for this video,. The codes told me what was wrong with my dryer,. It was not enough power. The breaker melted ..
WOW! I am sorry to hear it happened, but at least you know what needs fixed!
Thanks!
Hi there! Great instructional video! Will all these diagnostic steps work on a WED7000DW1?
It should
@@bensappliancesandjunk Thank you
I was able to get the error codes for my dryer. Thank you!
I have a cabrio washer no codes and it wont complete the last part of the spin cycle and it sounds like sandpaper rubbing together. Any ideas
Sounds like there may be a tub obstruction that's not letting the washer get up to speed for the final high-RPM spin. I hate to say take the drum out but... take the drum out and look for obstructions in between the plastic outer tub and metal inner tub. But before that - I'd check underneath the washer and see if maybe somethings' rubbing on the motor.
I have a model that looks just like this but is a washer (cabrio platinum). None of the ways I press or turn the dial lead me to the diagnostics mode. I am just trying to figure out why it's leaking from the front at the beginning of a cycle. Only cycle that doesn't leak is the "bulky" for some reason.
Where is it leaking at?
Leaking from bottom front of machine having same problem okay.@@bensappliancesandjunk
I have that same pos
I as well have that same pos 😅
Showed and F2 code unplugged the machine, plugged it back in, no lights on the control panel, light comes on when I open the dryer door?? Any suggestions.?
UI Failure. Check all connections going to board. Is it on a newer Cabrio Washing machine? One that has a sleeker all-black interface?
Is there a video on how to open the top ?
I want to clean it inside
Dryer powers up but will not start. I removed the thermal fuse, but the appliance store verified it's good. I have since gone through your recommended diagnostics. On my Cabrio dryer, I have no code display - just LED lights for each of the settings on the main panel. When I run through the diagnostics as you recommend (buttons 1,2,3 x 3 times) the "wet" LED blinks. I can find NO reference to what that means in my manual or online. Note: I hear a faint "click" when I hit the start button - is this an indication there's a problem with the relay/board?
Check the console for the schematics/manual. The key would be to make sure you have the technicians manual to confirm the 1-2-3 sequence is right for your specific dryer (Whirlpool is notorious for having 2 or 3 styles of diagnostic cadences on these units). Once you get that sheet, it SHOULD show you what the wet light is for. It does sound like a board issue / F1 code, but the sheet would help confirm that. On the board - usually if its bad on a dryer, you can remove the board and then take the plastic housing off the back. Many times, when you separate the board from the housing, you'll see a damaged/burnt relay spot which would confirm a bad board.
I have and electric dryer. I ran the diagnostic and the dryer ran for about 2mins and the code just gave a number 2. What does the 2 mean???
Thanks
I had the same thing
This was helpful, thank you. I didn’t get an error code but my dryer just won’t turn run. Is that a fuse maybe?
Yes. Very often, it won't show an error code for a bad fuse.
@@bensappliancesandjunk happened to me yesterday. Did some research today and found it might be a thermal fuse. Have to pretty much disassemble the dryer to get to it. But it'll be worth it if that's the problem
@@user_namehere the cabrios kinda suck to take apart. I do got a video of those if you needed it but its a $10 part vs. A $200 call for a tech. Not a bad deal
@@bensappliancesandjunk I just ran the diagnostics on my dryer (the process was a little different than your video) but it's showing an "F1" code. According to whirlpool I need to change the whole control module. Didn't know I had a code until now. Any thoughts on how to fix? Or should I just replace the control module?
@@user_namehereI would check the control board on the unit. Unplug it, take the top off, and look at the control board (plastic box). Unplug everything, take control board out of unit and then take the board out of the plastic housing. F1 codes on Cabrio or Duet dryers indicates that the Omron relay got destroyed, which would prevent it from running properly. This can be easily verified for looking for burned spots on the board.
Followed your video (great info by the way) and got the "88" code like you said. My "Sensing" light comes on but the motor won't start. I'm hoping it's a fuse in that it's a 150 lb paperweight currently.
I have same problem did you figure out the problem?
Yes, it was the thermal fuse. Cost $5 on Amazon and took approximately 10 minutes to fix-9.5 minutes to tear the machine down far enough to reach the fuse. It’s located on the right side in the front of machine under drum. Take control panel off, lay on its back, remove top, and front panel and door. Fuse sits in a white plastic air duct housing. Don’t forget to plug your door switch/light harness back in upon reassembly. I did and got to do it over again.
@@xxlpatriot3077 thanks so much, replaced mine 🤞 so far so good!
@@xxlpatriot3077 I had the same problem and did the same thing: didn't plug the switch/light harness upon reassembly. Fortunately, my wife tactfully asked about the dangling plug, I loosened the top (again), and plug the harness. Dryer worked perfectly! My wife...I think I'll keep her (42+ years married)!
When I press start on my washer it locks and start to full but three seconds after it stop and unlocks. It don't do anything else from there, and before it was washing but it wouldn't release the softer, or spin dry. What can possibly be wrong?
I would reset the unit (unplug it, give it like 15min to drain the capacitors and such). Plug it back in. Give it maybe 1 minute to boot up. From there, let it start and run for 15min. Some washers like this lock/unlock, then continue on the process to run things for a wash. There's usually a checklist on the system like:
- Does lid lock work?
- Does drain pump work?
- Does water valve work?
- Can basket spin freely?
If it passes those tests, it begins to sense the load (if auto-sensing) and begin the process of washing. If it fails a test, it usually kicks itself out of doing anything else. From there, you can usually put it in diagnostics to see what code is preventing it from running any further.
I’m literally at a lost , I for one absolutely hate this washer I have . I did what you said to my platinum washer but it did not do anything to reset it whatsoever . I do however have an issue with it when it reaches the spin cycle or constantly says UL across it , I’ve tilted the washer back and the bottom of the motor that makes it spin has left rust on my floor , it’s constantly off balance even when I’ve tried to run a simple small blanket :/ I just need some answers and help !
If the motor underneath is rusty, its likely its going bad, causing the unbalanced error codes. There should not be any rust or discoloration underneath, and if there's a sizable presence, it'd suggest somethings major wrong with the motor or associated components.
My cabrio dryer keep blowing off the fuse. In one year it blew off 4 times. 3 times in my old house and we just moved to new house 2 months ago and it happened again. Can you tell me what might be the problem?
I would make sure the inside of the dryer is VERY CLEAN. Cabrio dryers have a terrible tendency to get impacted with dirt and derbis which can stiffle heat moving out of the dryer, causing it to build up and trip the fuse. The same thing goes for your vents in the house... Make sure they are cleaned very well. Next, I would maybe look at replacing the thermostat and hi-limit cutoff to ensure its moderating temperatures properly if you trip any more fuses AFTER you clean out the whole unit really, really well.
Bens Appliances and Junk
Thanks for the message. We are seniors and I do not know how to change thermostat and cut off. I may have to call the appliance technician.
I need help with my cabrio platinum washer
Great Video. I was able to determine I have a "7E" error code. From what I find, that is overheating, correct? I have not yet checked the vent etc., but what would be the first thing I should look at? Also, how do I clear the error? I tried, but it did not clear...Thank you
Did you figure it out I have same code😊
What happens when you do the diagnostics test and everything comes out good but when you turn the dryer on the check vent light comes keeps coming on??? Please help
Is that preventing your dryer from running at all? I would check the thermal fuse, the aboard for physical damage, and then the wire harness going to the moisture sensor on the dryer
I have a Whirlpool Cabrio Dryer (electric) When I press the start button it just beeps and won't start. The timer will count down like it is running. I tried the diagnostics and button 2 and 3 just beep three times when short pushed. Button 1 works as you demonstrated. Any suggestions?
The 2 things I would check would be the white thermal fuse that is inside the dryer, that could be badd and I have seen it not display error codes. The other thing would be to check under the main board for burn marks
@@bensappliancesandjunk It was the fuse, thank you very much for your help!
Bens Appliances and Junk where would this fuse be located?
@@psychosis9989 blower housing. I've been trying to get one more of these in-stock to do a teardown video on, but none have popped up yet
Bens Appliances and Junk I’m having the same issue. Machine acts like it’s functioning normally. Timer counts down. But drum not spinning and no heat. I pulled and checked the thermal fuse but it’s showing .000 on my meter. My next thought was belt but it appears to be intact and all the rollers are rolling correctly. Please help
Can I interchange a whirlpool cabrio washer user interface board into a cabrio dryer?
No. It won't program right and you'll get errors
I just slammed the door twice and it went back to working. Problem solved.
Where do you find the error code at?
I have the platinum cabrio dryer and I got the code f2E1
My dryer says f1 e1 what should i do?
F1E1 is usually low power to unit, like your breaker or power cord is malfunctioning. I'd make sure breaker is fully reset, then if that doesn't solve it, get a multimeter or appliance tech to trace down why the unit thinks there's bad electric going to unit
I've tried everything everyone has said on here, along with what u have said, and I can't get my washer to do nothing, ugghhh I'm so frustrated right now
Hi mine has a F4 or E4 code could you help me out
It should be two codes, an F code and an E code. If its both, that's a really obscure code dealing with installing the unit at a house.
Err, I looked it up more. It could also be an improper L2 voltage, meaning something has happened to the electriity to where its failed to deliver the needed electric to run the dryer. That'd mean the terminal, cord, outlet, or breaker is bad.
Thanks a bunch I did have someone come fix it and a few months later it didn’t work it was a fuse he fixed and he charged me so much for it I’m kinda scarred to call someone else to come fix it I can’t afford the price the last person charged me and with Covid I don’t really want people up in my house 😞
I got the 88 but my dryer still won't start
Mine says E3 F3, what’s that?
Washer or dryer
SD error code o l error code DL error code but not all the same time. Two out of three Cycles get all the way to the end when the timer's down to three or four then go to SD. Other times it's DL
DL is an unbalance code i believe. SD is a long drain code. Your drain pump has an obstruction, or is too far in the sandpiper. Press the wash basket down far then release quickly. If the washer basket comes back and bobbles a little bit like a basket ball, the rods are bad. If it snaps back quickly and doesn't rebound at all, the rods are good and you may need to look at the washer being overloaded.
How to recalibrate washer
I need to no how to trouble shoot washer
You're going to have to be more specific for me to help you.
The worst washer I have ever owned oh my goodness. If you own this hunk of junk I feel your pain.
The Cabrio bearing/shaft is awful on these units. About 7-9 years in, you're gonna pay a tech $400 to replace it unless you want to DIY it yourself... Its doable (and with the right tools, very easy) but man... No washer should have a bearing or bracket die in 10 years.
@@bensappliancesandjunk if you replace the bearing/shaft how much life will you get out of the washer? Is it worth fixing? Or buy new?
@@yvonnecortez9595 a failed bearing is one of those "just junk it" fixes. Most techs will charge you $400+
However, it's a DIYers dream. The bearings are wildly cheap. Like $40-50. It's just a very time consuming fix. Done right, the new bearings will run 10 years before another failure.
You are absolutely right!
I have my for ten years it just now stop working any idea why it show E4and E 4 error memes?
I tried this on my wtw8000bw0 washer and nothing happened.
Same
My dryer has f4 e4
My machine won't let water to tub
I couldnt get it to work
Im sorry. There are other style cabrios that do have different input sequences
I can’t get my cabrio platinum to run after LD code
I have this model dryer, it powers on but when I hit the start button it just beeps once and the dryer doesn’t start. Please help
Did it give you any sort of error code when you put it into diagnostics?