I really appreciate you going through the the error codes and in details to fixing a problem. A lot of this information isn't present in the manual and isn't helpful when the times come to look for a solution. I ride a Vsett 11+ Grey and black version with updated display. 👍
When i turn on my hitway h5 800w it flashes errror code 7 but only for about half a second ive been riding it daily and havent noticed any issues. Can anyone help me understand what the issues could be and what i should do to resolve it
Great video, nailes it, I had the E10 error, and it was my wire that goes from my throttle to the controller. AS soon as I switched that wire, i was golden! Also, another thing for the E10, that u didn't mention, (this was told to me by a friend, so it COULD be wrong.), he said he got the E10 after a small crash he had, nothing serious, but it did press his brake lever in, and of course they have a safety feature that u cant use the throttle, if the brake is pressed on. Once he realized that his brakes were on, (when he tried to walk the scooter home), he fixed the brake wire, and the E10 went away. Like I said this is hear say, to be honest, i dont really know the dude that told me this, just thought id throw it in there, it may help someone, and save a few bucks. Thanks again for the video, and i subbed to your channel.
Interesting! Thanks for the use case. Brakes is normally E2 and in your friends case, we need to think more about why the brakes would affect communication between the controller and LCD. And also, thanks for the sub. Appreciate it.
I got the E 10 today but my voltage ⚡display goes from a full charge to straight cut off like dead. The display after a while it comes back on only to show a draining voltage ⚡ I really need to fix this problem 😭
Hi. I have a problem with inaccurate speed on the display and says error. I thinks that’s a problem with the calibration or wiring issues. What solve this problem ?
Oh my gawd! Thank you! I have been going back and forth with Varla “customer service” (a Zero 10x clone as I understand it), for a month regarding an E10 message, across dozens of emails and repeated trouble-shooting instructions to me (guided by completely ridiculous videos they send me that are crazy-insufficient), telling me to check (and video) various voltages, sending the resulting videos back to them. The latest message I received from this morning, from yet another customer, basically returns all the way back to the very beginning with “Jennie” telling me to do a test they described (and later told me was wrong), at the very beginning a month ago: ach CS person increasingly seems NOT to read the history. Absolutely absurd! Reaching the end f my limit I decided I’d just see it I could find a place to buy two new controllers and just replace them. Thankfully I found your very complete, clear, and complete video, something Varla should absolutely have done a month ago! (Again,across probably 25 back-and-forth emails). Thank you very very much!
I have a Vsett10+ Build (Legacy2.0 from IO Hawk 52v system) and i would to asking how i remove E00 on the display it comes only if the Vibration are coming hard and the EABS brakes me down what i could it be ? and the battery are full charged
Thank you for your Video. I have a zero 10x 60v and every time i hit a road bump, the rear motor stops working, i have to leave the throttle and push again and it works great until the next road bump. Any ideas?
@@IGNITION1978 Maybe you have bad connection or bad cords. It feels as it's more of a guessing game here. My suggestion is to check both motor and throttle connection. Unplug and plug them back together and maybe spray some electric spray. Start with the most easiest stuff. If that doesn't help then you have to go deeper. These connections should be outside of the scooter..not inside. Sometimes things can just be bad connection and when you drive on a bump it shakes and it acts like a off and on switch. This is just a wild guess...but you need to start somewhere. You can also put the scooter on a stand and start throttle a bit. Feel and drag the cords carefully...if the motor dies then there are something with the cord or the connections. Maybe the cord to the motor is more likely to be the fault because it's only the rear motor
Hello sir you look like you understand the scooter .. I have problem without show any error on display the problem is when starting the scooter he start to going by self without touch anything and pres the gas he can do like b b b b can go more faster
In my case, a 48v zero 8, after a 8 km ride from full battery, in the last km, a small uphill, at 28kmh, the voltage dropped to 0 when it reached 44V ,with er 06. It always does that at 44-43v, although cutoff and voltage are set correctly(48 and cutoff 39).Could it be the bms or should i check the controller?
What can I do if it gives me error 08 but the accelerator is fine and the magnet too... if I turn it on with one motor it doesn't give me the error but when activating both motors it gives me error 08... as extra data the lights stay on and when you want to turn them on, only the ones in the back and the one in the front don't turn on... the skate feels a little slowed down I hope you can help me
Hello Thanks for the instructions , What is when appears 2 horizontal line in E9 Nordic racer 600E scooter ? I do not find an explanation of error anywhere . Thanks
Hello, thanks for making the video (with a good explaination). I have a vsett 10+, I don't have an error code but the front wheel doesn't work anymore AND it is even blocking (like the eabs is active). Didn't find anything like this on the internet. Can this be fixed by doing something ? Kind regards
For your error 8, on my zero10x it's not the magnet or throttle, it has something to do with the cable as we've plugged it into a different screen and the error code still came up...
I have error code 08, it’s not on the display all the time. But when I pull the throttle the motor makes a clicking sound but no movement. I’ll check the throttle magnet position. It’s a Hero S8 btw , thanks
Nice video, thanks. I have a brand new 2022 Ghost and neither the rear LED lights or brake lights are illuminating (out of the box defect). The other (front and side) LED lights are ok. No error messages. Any idea where the problem may lie? I heard the Ghost has a similar set up to the Zero scooters but can't find any fixes online. Apollo is sending me two replacement lights but I'm guessing that, with a brand new scooter, the issue is not the lights (what's the likelihood of having two bad rear bulbs on a brand new scooter?) but perhaps an electronics issue elsewhere?
Best way to check is to disconnect your front lights and hook it up to your rear light connectors. If it lights up, then it’s the led lights, if it doesn’t then it’s the dc converter.
Merci beaucoup pour votre vidéo. Je rencontre un problème avec ma trottinette Zéro 9. Après qu'elle soit tombée en panne écran noir, j'ai acheté un nouveau display QS S4. Une fois le nouveau display branché j'ai une erreur E- 08. Comme c'est une erreur de display j'ai décidé d'acheter un autre display. J'ai acheté trois display différents QS S4 et à chaque fois j'ai eu une erreur E- 08. Auriez-vous un modèle à me conseiller avec la certitude qu'il soit compatible à 100% ? Bonne journée
Hello i have a tech life x7s and i got the error code 06 which is battery under voltage i gave full charge but now my scooter wont turn on Any idea on what i can do Thanks
Hi and thank you for your video! I started getting E10 today after replacing Controller B on my Mototec Thor scooter. It worked yesterday with the previous controller but it did not send the full power to the rear motor. Once I replaced the controller, E10 started flashing. I tried putting back the old controller but the error still exists. I removed and reassembled the throttle stick with the magnet again but the error still exists. This is a QS-S4 controller. Do you have any suggestions by chance? Is my LCD throttle bad and needs to be replaced? It just worked yesterday just fine. Is there any way to add another thumb controller instead of QS-S4 and use that instead? Please advise. Thank you!
ur controller may not be compatible. did u use original parts? is the controller version the same as that of the other controller...etc. not the right forum to discuss on youtube. get us on whatsapp or telegram.
Hi, I have a gyrocopters flash 3.0 which does not have any error code but the motor doesn't turn. All the systems looks they are ok but the motor simply does not turn.
I checked for a controller to the vsett8+ but can't find any...as i understand the zero 8 is the same so i could use a controller from that? Is it only voltage on the controller that are different on these models or is it more?
Hi 3 years ago I bought quickvolt 8. Few months ago my LCD (type QS S4)broke. So I bought a new one (type: LH 100-which is compatible with 48 v battery). So the thing is that it gives me type 6 error when I plug it in. The thing is there are no wire or battery problems...how do I know??? well when I put the old LCD everything is good no problems no nothing (my old LCD is good just a piece of plastic broke from the lever that s all). But when I put the new LCD it gives me the error. Can you help me?? What can I do?? I dont think I need to check the wires(the wires are fine since the old LCD works).
I'm getting error code 6 and 10 but mainly 6. Charges fine turns on and rides but any moment on the journey it loses power says e6 then turns off and I cannot turn back on unless I connect it to a charger, when I connect it it comes back on. I had 2 issues that may have caused this, my mudguard wires got abit shredded, so I've cut them off until I get a mudguard (shortened them) and taped them singular, 2 no issue I rod in the rain then didn't ride for 2 days and I could only turn 1 way, I sprayed wd40 amd then it worked again
HELP! i need to replace my original controller, vsett8. can i replace with controller with vsett8+ or other another vsett model controller? no information online . Hope you can help . also for error 10 u say something's not moving? what do you mean by this? looks like everything ur touching is moving. what am i missing? Thanks . /Bklyn👑
Hi i have a question about error in boyueda 5600w. Main throttle is lh-100 i have shortcut in usb line and throttle's done. i bought another lh-100 but ealier have lh-100 v.4 this one is lh-100 v.5. Have e 10 error. What can i do? thanks for answers!!!
Hi I have a problem with Vsett 8. It doesn't run anymore and from the motor comes while the throttle is on awful ticking and rattling only. It started to show E 09 error and now appears also E 00. Don't you know what that could mean?
I have an err08. I've checked the screw and magnet and they look OK. At the rear hub (actually the brake when I separate the wheel, but that makes no sense)is a hight pitched noise. Any idea?
I have this weird problem on my 10x 52V 23Ah. When fully charged I drive about 15km and scooter just turns off. It says error 6 and 10. During ride voltage never drops below 49V. But it just dies. Turning key does nothing, it shows no voltage. If I connect charger it comes back to life and usually show about 54V. I checked the wires and connectors, they all seems ok. Any suggestions? Thanks
@@unknownuser3988 I did some research and it seems to be obvious side effect of dead battery cell(s). Battery should be disassembled and each cell should be tested for capacity and voltage. Not an easy job for a beginner and some tools are required. Also, new and same cells should be available to replace dead ones.
hello I have the rear brake sensor that always marks on but instead the wheel turns and the scooter does not start me. Do you know what could be the problem? vsett 10
Bonjour mon ami bonne vidéo je me sui abonné tu le mérite bien sérieux. Il y a marqué e10 à ma trottinette électrique hitway h5 c'est pareil pour se modèle la stp mon ami
I got e10 for my ultron t128.. n dont know what problem.. try unplug betery cable still same. Try unplug controller cable also same.. any suggestion...? From malaysia.. tq
On my new QS-S4 i get Error10 but when i switch to my old dashboard my scooter works fine. How to solve it? My dashboard is fine because my friend tryed it on his scooter.
Peace and blessings. I own A zero 10 X And recently ran into some problems. I got caught in the rain one afternoon, and as I sat at a traffic light.. I accidentally triggered the throttle and the scooter took off out of my hand and crashed to the floor. My throttle broke as a result. I had some tape on me so I fastened the unit back to the handlebar and was able to drive it... However, Only my front wheel had power ! Nothing I could do to get the back wheel to engage. I took off the deck plate and found about a quarter of an inch water inside the battery storage compartment. Do you think it's possible that my voltage controller was fried? Considering When the scooter fell over, the water within doused the rest of the area.. Update * I bought a thumb throttle to replace my broken trigger throttle. When I installed it, my rear wheel began working again ! But* My scooter only does about 8 miles before it dies..... So back to my original question... Do you think if I replace the controllers internally, will it possibly restore some of my battery life? Thank you for taking the time to read this
Thank you for your question. Charge the battery to full before discharging. If the Error goes away then you can discharge it. If it does not, then it’s a controller issue.
Use old-style bulb, like this: en.wikipedia.org/wiki/Incandescent_light_bulb they are basically resistors that put energy into heat, so they doesn't care about voltage and alternating or direct current. Calculate bulb power (thus resistance) to keep current draw below 10A.
What about how to fix error code 06??? It's been charging for 8 hours minimum, the voltage on the LCD said it was at 58.3 but then error 06 when I tried to ride.
Just got my Vsett 10+ scooter, my NFC cards stopped detecting my key out of no where and left me stranded to walk it home. The display and blinking red light comes on, but card does not read. Please help
I need help. I try to unmount my engine of my zero 9 to redo the wiring. The issue is that the thing is glued ! After removing the motor screws, it’s glued… how can I remove it ?
i have an error E06 for zero 9 scooter.i have tried unpluged and repluged the cables and after i recharge 2 time fully but still i have the same error. can you please tell me what should i do now.
İ use Yakasuma Jaguar, i changed the throttle, so when put the new one E-6 error appears on the screen, but when put the old throttle no errors and the scooter works anyone knows what is the problem?
Does anyone know what the error 00 means? - problem is that the throttle won't work anymore. Already checked the magnietic strip and that's alright, so any help would be appreciated
![[LIVE] : ONE ลุมพินี 89 | คู่เอก "ยอดไอคิว vs คิริลล์"](http://i.ytimg.com/vi/Z3vYkHJ_5Ig/mqdefault.jpg)
I really appreciate you going through the the error codes and in details to fixing a problem. A lot of this information isn't present in the manual and isn't helpful when the times come to look for a solution. I ride a Vsett 11+ Grey and black version with updated display. 👍
He's knows his shit helped out heaps up an flying, thanks O G
What happened E00? Thanks
When i turn on my hitway h5 800w it flashes errror code 7 but only for about half a second ive been riding it daily and havent noticed any issues. Can anyone help me understand what the issues could be and what i should do to resolve it
Great video, nailes it, I had the E10 error, and it was my wire that goes from my throttle to the controller. AS soon as I switched that wire, i was golden! Also, another thing for the E10, that u didn't mention, (this was told to me by a friend, so it COULD be wrong.), he said he got the E10 after a small crash he had, nothing serious, but it did press his brake lever in, and of course they have a safety feature that u cant use the throttle, if the brake is pressed on. Once he realized that his brakes were on, (when he tried to walk the scooter home), he fixed the brake wire, and the E10 went away. Like I said this is hear say, to be honest, i dont really know the dude that told me this, just thought id throw it in there, it may help someone, and save a few bucks. Thanks again for the video, and i subbed to your channel.
Interesting! Thanks for the use case. Brakes is normally E2 and in your friends case, we need to think more about why the brakes would affect communication between the controller and LCD. And also, thanks for the sub. Appreciate it.
I got the E 10 today but my voltage ⚡display goes from a full charge to straight cut off like dead. The display after a while it comes back on only to show a draining voltage ⚡ I really need to fix this problem 😭
@@titusrichardson539 whats ur model
Hi. I have a problem with inaccurate speed on the display and says error. I thinks that’s a problem with the calibration or wiring issues. What solve this problem ?
It means your wheel size or your magnet settings are wrong
Oh my gawd! Thank you! I have been going back and forth with Varla “customer service” (a Zero 10x clone as I understand it), for a month regarding an E10 message, across dozens of emails and repeated trouble-shooting instructions to me (guided by completely ridiculous videos they send me that are crazy-insufficient), telling me to check (and video) various voltages, sending the resulting videos back to them. The latest message I received from this morning, from yet another customer, basically returns all the way back to the very beginning with “Jennie” telling me to do a test they described (and later told me was wrong), at the very beginning a month ago: ach CS person increasingly seems NOT to read the history. Absolutely absurd!
Reaching the end f my limit I decided I’d just see it I could find a place to buy two new controllers and just replace them. Thankfully I found your very complete, clear, and complete video, something Varla should absolutely have done a month ago! (Again,across probably 25 back-and-forth emails). Thank you very very much!
Thank you for your kind words! Help us spread the word
I got E08 issue followed your video but can't tell what wrong because the magnet and everything looks fine
Friend did you solve the issue, having the same problem now
You guys are the best, the most reliable chanell on youtube ❤️❤️🙏🏼
thank you you for your continued support!
I have a Vsett10+ Build (Legacy2.0 from IO Hawk 52v system) and i would to asking how i remove E00 on the display it comes only if the Vibration are coming hard and the EABS brakes me down what i could it be ? and the battery are full charged
Thank you for your Video. I have a zero 10x 60v and every time i hit a road bump, the rear motor stops working, i have to leave the throttle and push again and it works great until the next road bump. Any ideas?
Hi does it happen with front or rear motor? Single or dual mode?
@@FalconpevSg it happens in rear motor only, on both modes, single and dual , no difference.
Any news?
@@IGNITION1978 Maybe you have bad connection or bad cords. It feels as it's more of a guessing game here. My suggestion is to check both motor and throttle connection. Unplug and plug them back together and maybe spray some electric spray. Start with the most easiest stuff. If that doesn't help then you have to go deeper. These connections should be outside of the scooter..not inside. Sometimes things can just be bad connection and when you drive on a bump it shakes and it acts like a off and on switch. This is just a wild guess...but you need to start somewhere. You can also put the scooter on a stand and start throttle a bit. Feel and drag the cords carefully...if the motor dies then there are something with the cord or the connections. Maybe the cord to the motor is more likely to be the fault because it's only the rear motor
Great video.
I have seen the Error 00 twice on my Vsett 10+. It has gone away as noted, but I'd like to know what causes it.
We aren’t sure if not we will definitely solve it.
@@FalconpevSg same, looking for the cause
Me too.. why? Thanks
same - E00 twice already in last 3 rides - had to turn off and on again.
Yup this just happened to me today
Just order a scooter with this setup controller Thanks for the info
Hope you enjoy it!
hi thanks for the help.. i have the e 10 error and i was wondering where i can get the new harness wire for my zero 10x?
Hello sir you look like you understand the scooter .. I have problem without show any error on display the problem is when starting the scooter he start to going by self without touch anything and pres the gas he can do like b b b b can go more faster
try changing a new LCD
In my case, a 48v zero 8, after a 8 km ride from full battery, in the last km, a small uphill, at 28kmh, the voltage dropped to 0 when it reached 44V ,with er 06. It always does that at 44-43v, although cutoff and voltage are set correctly(48 and cutoff 39).Could it be the bms or should i check the controller?
do you have video for miss aligned back tire? i really need to know why my tire looks wiggle
Yes look up our channel we have a video on that
Excellent video! Thank you VERY much for it!
@@termitektermit7889 glad it helped you
Hello do you know what error 00 means on my vsett 10+?
What can I do if it gives me error 08 but the accelerator is fine and the magnet too... if I turn it on with one motor it doesn't give me the error but when activating both motors it gives me error 08... as extra data the lights stay on and when you want to turn them on, only the ones in the back and the one in the front don't turn on... the skate feels a little slowed down I hope you can help me
I have the same issue on a vsett 9 plus, did you get help
Yo have u guys ever seen a zero charger bink red when not connected to the scooter? Great zero videoes so much to see :D
the charger is spoilt, need to change it. thank you!
What is the cut-off voltage for Vsett9+? It has 48V battery.
Hello Thanks for the instructions , What is when appears 2 horizontal line in E9 Nordic racer 600E scooter ? I do not find an explanation of error anywhere . Thanks
Hello, thanks for making the video (with a good explaination). I have a vsett 10+, I don't have an error code but the front wheel doesn't work anymore AND it is even blocking (like the eabs is active). Didn't find anything like this on the internet. Can this be fixed by doing something ? Kind regards
Controller issue, mosfets are burnt
@@FalconpevSg thanks for the response. Happend after some days of use (30miles). I will bring it back to the shop 😉
Hello could error 07 be my controller? Like the phase wires or mosfets could still give our motor faults?
The best way to find out is to disconnect your motor and turn on your scooter. Is the error code still there?
Great job can you do a video on how to open the vsett8 please? Keep up the good work!!
Pls help to spread the word:) vsett 8 is the same as zero 8. You can find it here: th-cam.com/video/vrf1fpAByxM/w-d-xo.html
Hi, i have error 6, (zero 9, qs-s4 control)and when I try to charge the indicated light is always green. Solutions?
Did you ever find the fix for this?
For your error 8, on my zero10x it's not the magnet or throttle, it has something to do with the cable as we've plugged it into a different screen and the error code still came up...
Hi sorry we missed out a part. It could also be your motor hall sensor. Unplug your motor cables and see if the error persists
did you fix the issue?
I have error code 08, it’s not on the display all the time. But when I pull the throttle the motor makes a clicking sound but no movement. I’ll check the throttle magnet position. It’s a Hero S8 btw , thanks
Nice video, thanks. I have a brand new 2022 Ghost and neither the rear LED lights or brake lights are illuminating (out of the box defect). The other (front and side) LED lights are ok. No error messages. Any idea where the problem may lie? I heard the Ghost has a similar set up to the Zero scooters but can't find any fixes online. Apollo is sending me two replacement lights but I'm guessing that, with a brand new scooter, the issue is not the lights (what's the likelihood of having two bad rear bulbs on a brand new scooter?) but perhaps an electronics issue elsewhere?
Best way to check is to disconnect your front lights and hook it up to your rear light connectors. If it lights up, then it’s the led lights, if it doesn’t then it’s the dc converter.
Thank You! I have an error 8. The magnet is gone! Where can I get a replacement? Thanks
Merci beaucoup pour votre vidéo. Je rencontre un problème avec ma trottinette Zéro 9. Après qu'elle soit tombée en panne écran noir, j'ai acheté un nouveau display QS S4. Une fois le nouveau display branché j'ai une erreur E- 08. Comme c'est une erreur de display j'ai décidé d'acheter un autre display. J'ai acheté trois display différents QS S4 et à chaque fois j'ai eu une erreur E- 08. Auriez-vous un modèle à me conseiller avec la certitude qu'il soit compatible à 100% ? Bonne journée
HEY MY Vsset 9 + Don’t turn on off de Dual motor what do u think can cause this problems ???
Hello i have a tech life x7s and i got the error code 06 which is battery under voltage i gave full charge but now my scooter wont turn on
Any idea on what i can do
Thanks
Hello I need help to fix error 8 I’ve did everything you guys did and it’s still there would it still stay there if I replace the lcd screen
Have you already replaced the lcd?
@@FalconpevSgNo not yet if the error 8 goes away I’ll be happy to buy a new LCD
@@sovanarithkong716 yes most likely, you can buy one and try, it’s not that expensive
Thank you guys
Great job, How do you reset back to factory (p) setting including passcode?
You can’t
Kaabo Skywalker 10C anyway to short wires to see if motor working v?
I have a caroma e scooter with error code 10 just happened to day and the scooter wont turn on and i was woundering will this work for me
Hi and thank you for your video! I started getting E10 today after replacing Controller B on my Mototec Thor scooter. It worked yesterday with the previous controller but it did not send the full power to the rear motor. Once I replaced the controller, E10 started flashing. I tried putting back the old controller but the error still exists. I removed and reassembled the throttle stick with the magnet again but the error still exists. This is a QS-S4 controller. Do you have any suggestions by chance? Is my LCD throttle bad and needs to be replaced? It just worked yesterday just fine. Is there any way to add another thumb controller instead of QS-S4 and use that instead? Please advise. Thank you!
ur controller may not be compatible. did u use original parts? is the controller version the same as that of the other controller...etc. not the right forum to discuss on youtube. get us on whatsapp or telegram.
Where to buy wire I have E 10 in my EverCross and how to fix please. Thanks.
Controller Wire harness ?
Hi, I have a gyrocopters flash 3.0 which does not have any error code but the motor doesn't turn. All the systems looks they are ok but the motor simply does not turn.
Had q30 for one day and back wheel doesn't want to work right are is it the motor
I own Jetson Electric scooter, model Element Pro with a E2 error what could be the problem and how to fixed?
I had 4 times 00 error in my vsett 10, I want to know, what is the cause for this error? Snd how can I solve it? Thanks
It might be related to an intermittent connection in the lcd so just change lcd
I checked for a controller to the vsett8+ but can't find any...as i understand the zero 8 is the same so i could use a controller from that? Is it only voltage on the controller that are different on these models or is it more?
What means E02 error on my fundot f8 electric scooter ?
My scooter come up E10 ,how can I reset it or get ripp it off?
E10 is tricky. It could be wire harness from lcd to controller that’s causing the issue
Hi 3 years ago I bought quickvolt 8. Few months ago my LCD (type QS S4)broke. So I bought a new one (type: LH 100-which is compatible with 48 v battery). So the thing is that it gives me type 6 error when I plug it in. The thing is there are no wire or battery problems...how do I know??? well when I put the old LCD everything is good no problems no nothing (my old LCD is good just a piece of plastic broke from the lever that s all). But when I put the new LCD it gives me the error. Can you help me?? What can I do?? I dont think I need to check the wires(the wires are fine since the old LCD works).
I'm getting error code 6 and 10 but mainly 6.
Charges fine turns on and rides but any moment on the journey it loses power says e6 then turns off and I cannot turn back on unless I connect it to a charger, when I connect it it comes back on. I had 2 issues that may have caused this, my mudguard wires got abit shredded, so I've cut them off until I get a mudguard (shortened them) and taped them singular, 2 no issue I rod in the rain then didn't ride for 2 days and I could only turn 1 way, I sprayed wd40 amd then it worked again
HELP!
i need to replace my original controller, vsett8.
can i replace with controller with vsett8+ or other another vsett model controller?
no information online . Hope you can help .
also for error 10 u say something's not moving? what do you mean by this? looks like everything ur touching is moving.
what am i missing?
Thanks .
/Bklyn👑
Hello please reply, if I buy scooter with error code 09.. could it just be the controller or could there be hidden problems?
Hi i have a question about error in boyueda 5600w. Main throttle is lh-100 i have shortcut in usb line and throttle's done. i bought another lh-100 but ealier have lh-100 v.4 this one is lh-100 v.5. Have e 10 error. What can i do? thanks for answers!!!
Error 10 is normally communication error, meaning the new lcd is not compatible
@@FalconpevSg thx for answer. But i cant find lh-100 v.4 please tell me what throttle i should buy or what can i do with v.
.5
Do you know what is wrong if the p-12 setting of acceleration does not work on the zero 8 scooter?
On mine there is no difference between setting 1-5.
Hi I lost my fobs for vsett 10 plus I have brought 3 priganal replacement fobs but won't start the scooter any ideas.
Hi I have a problem with Vsett 8. It doesn't run anymore and from the motor comes while the throttle is on awful ticking and rattling only. It started to show E 09 error and now appears also E 00. Don't you know what that could mean?
First check your motor wire connector, is it ok?
I have an err08. I've checked the screw and magnet and they look OK.
At the rear hub (actually the brake when I separate the wheel, but that makes no sense)is a hight pitched noise.
Any idea?
Error 8 may also be motor hall sensor issue.
@@FalconpevSg And if it is the motor hall sensor, how can I repair it?
I have this weird problem on my 10x 52V 23Ah.
When fully charged I drive about 15km and scooter just turns off. It says error 6 and 10. During ride voltage never drops below 49V. But it just dies. Turning key does nothing, it shows no voltage. If I connect charger it comes back to life and usually show about 54V. I checked the wires and connectors, they all seems ok.
Any suggestions? Thanks
Got the same problem
@@unknownuser3988 I did some research and it seems to be obvious side effect of dead battery cell(s). Battery should be disassembled and each cell should be tested for capacity and voltage. Not an easy job for a beginner and some tools are required. Also, new and same cells should be available to replace dead ones.
Battery is just under two years old, my odo shows about 3000km. Cells are LG.
@@radoskasan Then I wouldn't be surprised if there is a problem with your battery.
hello I have the rear brake sensor that always marks on but instead the wheel turns and the scooter does not start me. Do you know what could be the problem? vsett 10
My shows error 3? No clue wat it is..can u please help
Bonjour mon ami bonne vidéo je me sui abonné tu le mérite bien sérieux. Il y a marqué e10 à ma trottinette électrique hitway h5 c'est pareil pour se modèle la stp mon ami
I got e10 for my ultron t128.. n dont know what problem.. try unplug betery cable still same. Try unplug controller cable also same.. any suggestion...? From malaysia.. tq
Ask seller
hello. what's E-0 problem on display screen? I have got iscooter IX5 scooter
Great video!
Thank you
I’ve got Fiido m1 pro E bike. It’s showing E4 on the screen. What’s the issue please
we dont sell the fiido m1 so we cant help there.
I have code E5. What is that problem and how to fix it? Thanks
On my new QS-S4 i get Error10 but when i switch to my old dashboard my scooter works fine. How to solve it? My dashboard is fine because my friend tryed it on his scooter.
hello. The rear wheel does not turn me error e09 what could be the reason?
my zero10x gave me err 06 at 41-42V(cutoff 39) should I worry?
No 41V is very low
@@FalconpevSg Thank you for the quick answer! appreciate it!!!
Peace and blessings.
I own A zero 10 X
And recently ran into some problems.
I got caught in the rain one afternoon, and as I sat at a traffic light.. I accidentally triggered the throttle and the scooter took off out of my hand and crashed to the floor.
My throttle broke as a result.
I had some tape on me so I fastened the unit back to the handlebar and was able to drive it...
However, Only my front wheel had power !
Nothing I could do to get the back wheel to engage.
I took off the deck plate and found about a quarter of an inch water inside the battery storage compartment.
Do you think it's possible that my voltage controller was fried? Considering When the scooter fell over, the water within doused the rest of the area..
Update *
I bought a thumb throttle to replace my broken trigger throttle.
When I installed it, my rear wheel began working again !
But*
My scooter only does about 8 miles before it dies.....
So back to my original question...
Do you think if I replace the controllers internally, will it possibly restore some of my battery life?
Thank you for taking the time to read this
Now after hearing the full story I think your battery may be the problem. Controllers isn’t the problem if it works normally.
I have this problem right now mate so all i need is a new throttle?
Nice Video, How do you discharge a battery (cycle) if you have an error code and the scooter doesn't move?
Thank you for your question. Charge the battery to full before discharging. If the Error goes away then you can discharge it. If it does not, then it’s a controller issue.
Use old-style bulb, like this:
en.wikipedia.org/wiki/Incandescent_light_bulb
they are basically resistors that put energy into heat, so they doesn't care about voltage and alternating or direct current. Calculate bulb power (thus resistance) to keep current draw below 10A.
@@uosiumen thank you foe the good idea
Thanks, great advise!
No problem!
i have the Yugen RX10. i just took my tire off to replace, my scooter is now saying Error 7 what does that mean?
Please help me, the tail lights are still on, romobil don't want to start, what is the problem?
Hey friend where can I buy the thing to solve errorcode 10 i have zero 9
Do you happen to know the error codes for a fiat 500. 01 error code and beeping
Sorry we don’t
@@FalconpevSg thanks anyway.
Wot about error codes for kaboo I'm having problems with error code 10
Sir question, E10 lcd wont turn on, but lights are working, how to fix it sir?
i had bought a brand new Iscooter i9 Max. and there is a e10 error code before i even rode it. how do i fix this?
Return it
Hello, I bougjt the throttle lcd for zero 10x with power supply and it says error no.8 I did everthing, still doesnt work.
i have a error 7 come up only if my lights are on , if i turn them off the error goes away , what can corse this ?
flashing error code on my nfs reader vsett 10+ dont start help plz
I have gt 100 and how can i fix error 28 and 30?
Bro, I have error e 06 and only front motor working? Any advice where I should check
E06 try to charge your battery first
@@FalconpevSg Thank you. Do you have a repair shop in London or Manchester?
@@moldovansebastian6533 yes check out PET
Hi i have also error 001 what should i do for ky e10
HI Plese Mack Hero Z8 Video Thanks
What about how to fix error code 06??? It's been charging for 8 hours minimum, the voltage on the LCD said it was at 58.3 but then error 06 when I tried to ride.
Were you able to find a fix?
Just got my Vsett 10+ scooter, my NFC cards stopped detecting my key out of no where and left me stranded to walk it home. The display and blinking red light comes on, but card does not read. Please help
Have you resolved you issue same thinh happens with me
You can read it in the manual about the cards
I have error e08 on double motor and en simple motor i have error Throttle not work on simple motor
My vsett 9 error 06 what should I do?
I need help. I try to unmount my engine of my zero 9 to redo the wiring. The issue is that the thing is glued ! After removing the motor screws, it’s glued… how can I remove it ?
its not glued, its the magnet holding it together. is yours a real zero 9?
@@FalconpevSg no it’s real glue, I can scrap it in some places… no it’s not the real one, there are the zero signs a bit everywhere but it’s a “blaze”
Hi have have m4 kungoo error 5 any help pls
Hi I have the 08 fault code but when I press the eco/turbo button the front motor tries to turn.
Can you help
I’m having this same problem I can’t figure it out did u solve it??
Guys please did anyone fix this problem
the 00 returned after restarting the scooter. And i had 53v on battery and it already lost the power even on one motor.
i have an error E06 for zero 9 scooter.i have tried unpluged and repluged the cables and after i recharge 2 time fully but still i have the same error. can you please tell me what should i do now.
motor error.
@@FalconpevSg should i need to change
my Q7 scooter shows me error E-006 i dont know why its shows me since 3 months and i cant drive it
I turn it on and the front motor works but rear stiffens up and doesn't run
İ use Yakasuma Jaguar, i changed the throttle, so when put the new one E-6 error appears on the screen, but when put the old throttle no errors and the scooter works anyone knows what is the problem?
What is error code number 4
Does anyone know what the error 00 means? - problem is that the throttle won't work anymore. Already checked the magnietic strip and that's alright, so any help would be appreciated
Just turn off and on it’s nothing
@@FalconpevSg well the nothing is that it won't start. it worked for 4 days and just stopped working.
@@TheoriginalMach2000 try unplugging the lcd and plugging it back in?
Hi my scooter stopped working and is saying 000 error how do I fix it please
I have a zero 10 . When the battery is on the third light blinking. The scooter turns off with out any warning.
What do you mean third light blinking?