p17 is Cruise mode you said if you want cruise set it to 1 and if you want cruise set it to 0. that was a confusing bit? how does the cruise control work please? kind regards.
I managad to figured that out myself it took me a while , 1. turn the scooter on and enter the password you have so it will go into the on state. 2. hold power button and mode button together (you'll get a popup for a password) 3. enter "1111" 4. it will ask for a password again this time enter "0000" 5. this will now make your scooter without password and should allow you to turn it on and off without pass. if you need help go ahead and PM me,i can always make a video if needed.
someone had a problem error 09 (contoller) in his lcd for his scooter, What is the problem ? how to resolve it or réinitializing it please ? he can not use it now same scooter was dammaged
Hey please help me, i have the zero 10x and Under the cable shield in the handlebars there is a wire inside which there are 3 wires inside of him: red, green and black and they were wrapped in white tape in a bad way so I wanted to replace the tape and then suddenly the scooter stopped working and did not open again... please tell me what to do if you .
Riding motorcycles for decades I was shocked how un stable this machine is. Anything that goes over 15kph should have some sort of stability. On this machine, if you scratch your nose with one hand while you are cruising at 60kph, you will crash. I demonstrated this at 40kph. On a motorcycle the steering geometry is such that its trail ensures hands off stability. These cheap Chinese powerful scooters have no regard for personal safety which could be remedied with a slight design change.
How to get my zero10x taillights standby? If I hold the mode button to turn on the lights. It lights the front only. Back light works if I just press the breaks.
hi tnx for the guide. when i in the settings menu (p-settings) , and i long press the power button, the "A" in the bottom line changes to "D". do you know what is the purpose of this mode A/D ?
Does anyone know if the QS-S4 LCD throttle unit for this Zero 10X scooter will be compatible with Mototec Thor 60V scooter? I am looking for a spare QS-S4 for my Mototec scooter and they are sold out everywhere.
Does electronic braking on this actually work? I didn’t see any difference when I tested it up on the chair so the wheels can freely move and I didn’t notice any difference after letting go of acceleration whether electronic braking actually works, I went through level 1 to 5 in P11 and didn’t see any difference
Ahh I can confirm it does work. Once you get up to higher speeds and you pull the brake lever lightly the regen brake kicks in and you can hear the motor whine
Can anyone help me. I got this LCD and controller. I got 3 modes. But I need to start slowly. Why is it not possible to change speed? Why is is only 3 speed settings? It makes no sense.
How can i see the remaining voltage in the display? The bars are not accurate. ¿Cómo se puede ver en el display el voltaje restante de la batería? Las barritas no son nada exactos.
Hey, how can i find out what my cut off is? Like when my voltage gets too low, i believe it cuts off when the battery reaches a certain percentage. Anyone know how to check that? Thanks in advance.
go in to the p menue and volt on my scooter not zero i can adjust the cut off higher and when it cuts i have spare power to take me home like a reserve fuel tank WARNING don adjust it lower you wil have more range yes but it can damage the battery
@@CarleyEspritPhilip Yah, mine was aet at 42 and the actual cut off i believe it 41, or maybe 40, u could google it to be sure, but mine is a 52 volt, and the cut off is at 42. Have fun and ride safe!!
I know this been so long ago.. Can ask why my scooter battery guide is allways 100% I mean full green bar but . I'm driving then suddenly batery empty..
I brought a this set controller but when I connect the wires( only battery wire and 3 phase wires ) "warning sign" blink and when accelator is increased "countinous speed " signs appears, any one can help me please.
Thanks for the heads up! One question when my scooter is under load the battery shows it near empty, when I release the throttle it climbs back up? Is this normal?
i can tell u that mate! when u use the throttle at 30 % battery it shows you, if u hold this acceleration u get this far . but if you now take your throttle at 70% it shows you how long u can get at 70% throttle, sorry for my bad english !!
@@husse843 Translation 3 years later = If you hold your acceleration at 100% the voltage will drop as your sucking more juice and will show you how far you can travel at 100% throttle. If you hold it at 50% throttle instead of 100%, it’ll change and calculate the new distance you can travel based upon power consumption being used from pulling down on the throttle. Lighter throttle = less juice being sucked out = more distance available to travel before battery dies.
@@modzmetropolis9558 actually there are no calculations or anything fancy, the reason the bars drop is because they are based on current voltage if you are using the throttle you are putting load which drops the voltage
Hi, i have a question, when i enter the P settings and long push the on/off button, the letter ''A'' on the bottom left changes to the letter ''d'' And I wondered what it does... so if you know please tell me :)
New batch of zero8v2? What should be default number of magnets? Based on the video it should be 30 but i receive it 28 only please confirm which is correct
I've had send the following:: P01: Backlight brightness, level 1 is the darkest, level 3 is the brightest; P01 defaults to 2 P02: mileage unit, 0: KM; 1: MILE; P02 defaults to 0 P03: Voltage level: P03 defaults to 60V P04: Sleep time: 0, do not sleep; other numbers are sleep time, range: 1-60; unit minutes P04 default is: 10 P05: Boost gear: 0: 3 gear mode; P05 defaults to 0 P06: Wheel diameter: unit, inch; precision: 0.1; P06 default is 11 P07: Speed measuring magnet number: range: 0-255; P07 default is 30 P08: Speed limit: Range 0-100km / h, P08 defaults to 100 P09: Zero start, non-zero start settings, 0: zero start; 1: non-zero start; P09 defaults to 0 P10: Drive mode setting 0: Power-assisted drive (The power-assisted gear determines how much power is output. The handle is invalid). 1: Electric drive (drive through the knob, the power assist position is invalid at this time). 2: The power drive and the electric drive coexist at the same time (the electric drive is invalid in the zero-start state). P10 defaults to 2 P11: Boost sensitivity setting P11 defaults to 3 P12: Boost start strength setting P12 defaults to 3 P13: Type setting of power magnetic disk P13 defaults to 12 P14: Controller current limit value setting Range: 1-20A P14 defaults to 12 P15: controller undervoltage value P15 defaults to 49 P16: ODO clear setting Long press the plus button for 5 seconds, ODO clear P16 default is 0 P17: 0: Disable cruise, 1: Enable cruise; Auto cruise is optional (only valid for No. 2 protocol) P17 defaults to 0 P18: display speed proportional adjustment Range: 50% ~ 150%, P18 defaults to 100 P19: 0 gear enable bit, 0: with 0 gear, 1: without 0 gear P19 defaults to 1 P20: 0: No. 2 protocol 1: 5S protocol 2: standby 3: standby P20 defaults to 0 So the P11 is regen brake or something else?
Can you explain what p18 does? When I got my mx60 my settings were different..p18 only went upto 100. It is possible that I accidentally programmed my LCD controller for a different scooter? All my settings have changed. Is there a way to change it back?
hello. I have an electric scooter and it has the same display, or is it very similar. I would like to know if you could help me with a question that I have. Today when I was going to work, the scooter lost power, but when I stopped, I saw that the display and the ignition were still on, but the accelerator did not work. So I turned everything off, and turned the contact back on, but when I went to turn on the display, it doesn't respond. then at home, I was able to see and verify that the current reaches the display connector perfectly. . Is it sure that the display will be the problem? I also see that there are many models that are the same or very similar on the outside, how can I know if it will work on my scooter? Thank you
@@FalconpevSg Thats the big problem,. since I bought it in AliExpress, and then the store stopped selling in AliExpress, so I can't use the same store that I bought the scooter.. So... if I buy one with 6 pins, and I review the cables, each one in its color... it won't work? thank you
What do to if the charger light don't turn from red to green even though the step is fully charged (i can see that on my screen and my voltage is 65. I have a 60V). Can it do damage to my battery? Thanks!
i need a video on how to put a electric voltage monitor on this lcd ...you already have one for the older 8 but i have the newer 8 with this controller
Sir may i ask i have a problem with my parameter, the battery indicator is blinking into a lowbat but the volt is 41v, i charge its only 3 hours then the light indicator on charger is green, but still the icon of battery is still blinking,but the scooter is working and running, i want to send a video to you but cannot here, please help me thank you.
2 years ago I remember I was able to turn on "6kmh cruise" mode for my Zero 10X by pressing and holding some buttons. It was very useful when walking and pushing the scooter, but I don't remember how exactly I enabled it. Do you have any information how to enable this walking cruise mode?
Hi falcon I really hope you can help me as my vendor isn't being very helpful :( So I bought a mercane mx60. I tried to unlock the full speed and I believe I made a mistake as the settings are different now. P18 only used to go to 100, now it goes to 150. I am wondering. Could I have accidentally programmed it for a different scooter? Althought I have changed the speeds it feels slower and more sluggish than when I first got it and the speed (p8) was set to 35 :( Also, sometimes when I turn it on or press buttons I get a red exclamation! And a "e" comes up then goes away. Sometimes I set the settings and they will change on their own. It is a really heavy scooter and now it barely moves in single motor Please if anyone can help I would really appreciate it. Thank you
I messed with the programming stuff and i almost died on it. Is there any way to reset it to factory settings or something? Scooter wouldnt stop and brakes are really violent. Please help!!!
Please help I brought my 10x from you guys So happy!! I had a full charge on the scooter and completed a 4 mile ride and then turned it off. I returned later the same day and turned the scooter on to find the battery Barr apparently was empty and was flashing with the red warning triangle next to it.. Thank you.
What exactly does the high beam symbol do when hold mode button ? Is there a cable from the controller that is switched on ? If , what color and voltage ? Thx
Thanks for this video! When I try to get the P program menu it goes to a menu PO from there I can’t access to the program menu! Its posible that my scooter has that menu locked?
After you change the settings, does it automatically save or you have to readjust every time? I didn't see a save feature after you exit the settings menu at the end. Thank you for the informative video!
19 makes it so theres a gear zero so when you hitt the trottle the scooter wont move try it out😊
please the PAS is not working with this controller ? what is the reason , i used 3 different pas and not working , thank you
Hello I Have zero 8 my scooter is not changing gear.
Controller issue
Can I settings each mode of max speed? e.g. Mode 1(low) is 10kmh , Mode 2 (Mid) is 20kmh, Mode 3(high) is 30kmh. How to do it??
P08 - Power Level (0-100)
Thanks, goodness I couldn't figure out how to turn on the headlight.
Is this the same throttle as the jue Shuai x48?
Model is QS-S4
Hi, for the Zero 10 X what's the regular settings for P15? Is it 42 or 44? Pls advise
Did you find an answer? I'm struggling
@@scottireed2093 Mines set at 42
@@darkcrystal438 thank you for replying!
@@scottireed2093 no problem mate! Im currently setting the steering tension on my 10x right now ha ha.. was a bit stiff.
p17 is Cruise mode you said if you want cruise set it to 1 and if you want cruise set it to 0. that was a confusing bit? how does the cruise control work please? kind regards.
@M. Nurhaikal Hold the same speed for 4-5 seconds and it will be on (signaled by a blue icon on the dash).
I managed to set a password using s1 function that i cannot remember. any idea how to reset it ? or is it even possible?
I managad to figured that out myself it took me a while ,
1. turn the scooter on and enter the password you have so it will go into the on state.
2. hold power button and mode button together (you'll get a popup for a password)
3. enter "1111"
4. it will ask for a password again this time enter "0000"
5. this will now make your scooter without password and should allow you to turn it on and off without pass.
if you need help go ahead and PM me,i can always make a video if needed.
Florian De Graef make a video please
9221 then hold power
someone had a problem error 09 (contoller) in his lcd for his scooter, What is the problem ? how to resolve it or réinitializing it please ?
he can not use it now same scooter was dammaged
Hey please help me, i have the zero 10x and Under the cable shield in the handlebars there is a wire inside which there are 3 wires inside of him: red, green and black and they were wrapped in white tape in a bad way so I wanted to replace the tape and then suddenly the scooter stopped working and did not open again... please tell me what to do if you .
We can’t help without pics. Pls email us at sales@falconpev.com.sg
How to clear the odometer p16? Thanks
When i try to go into P menu it shows me a big 50 number and asks for some kind of 4 digit password, which i dont know
How to eliminate the 25km/h speed limit? from all3 modes with P08 to 100 only get 25km/h
Riding motorcycles for decades I was shocked how un stable this machine is. Anything that goes over 15kph should have some sort of stability. On this machine, if you scratch your nose with one hand while you are cruising at 60kph, you will crash. I demonstrated this at 40kph.
On a motorcycle the steering geometry is such that its trail ensures hands off stability. These cheap Chinese powerful scooters have no regard for personal safety which could be remedied with a slight design change.
Yes these do not allow for one handed steering. Having a motorcycle style rake angle will make the whole thing much larger
I have Regen on but when I press brake it is only stoop giving power to the motor and the wheel is still rolling
I've lost a rew numbers 8 12 n so on how do I get my zero 10x bk to normal
Hello,
if I set to 36V instead of 48V on my Zero 8 I will have more autonomy ?
No it will probably cut out a lot sooner
Up to which speed does P12 settings make a difference in acceleration?
Mostly at start
How the electronic braking works ?? Thanks
How can you adjust the batterie level.?
Help i cant find the 4 digit code
How to change speed,i buy bolzzen dynamo, original just can go 19kmh,i aready set P8 100,but nothing change just go 19kmh..pls advice
halo can you halp my i need the pin cod to p setting please my qs s4 thenks
hallo
habe faulty comms between controller and LCD was kann ich machen
danke für die hilfe
What is the red (!) on the top right when you hit the brakes Zero 10X? I am not sure my electronic brakes are working.
Hi Red Exclamation mark means brakes are on!
It means your brake lights are flashing in hazard mode
How to get my zero10x taillights standby? If I hold the mode button to turn on the lights. It lights the front only. Back light works if I just press the breaks.
Nice thanks
hi tnx for the guide. when i in the settings menu (p-settings) , and i long press the power button, the "A" in the bottom line changes to "D". do you know what is the purpose of this mode A/D ?
Hi, after the long press on power and mode buttons i get screen with password "SO" do you know what is the pass ?
TAI
It shouldn’t have that
whats the code for SO Mode
I don't have P8 power level. But the P15 is 100. By any chance the power level is P15? Then again i don't have Cut off voltage. Kindly advise.
Does anyone know if the QS-S4 LCD throttle unit for this Zero 10X scooter will be compatible with Mototec Thor 60V scooter? I am looking for a spare QS-S4 for my Mototec scooter and they are sold out everywhere.
Very helpful, thankyou.
David Michael thank you!
Does electronic braking on this actually work? I didn’t see any difference when I tested it up on the chair so the wheels can freely move and I didn’t notice any difference after letting go of acceleration whether electronic braking actually works, I went through level 1 to 5 in P11 and didn’t see any difference
Ahh I can confirm it does work. Once you get up to higher speeds and you pull the brake lever lightly the regen brake kicks in and you can hear the motor whine
Can anyone help me. I got this LCD and controller. I got 3 modes.
But I need to start slowly. Why is it not possible to change speed? Why is is only 3 speed settings? It makes no sense.
P15 ? zero 11x battery 72v 32 ah
How can i see the remaining voltage in the display? The bars are not accurate.
¿Cómo se puede ver en el display el voltaje restante de la batería? Las barritas no son nada exactos.
Please to claim a heal i want to know Please because I am not able to claim the heal with my 0-10 scooter electric
Hey, how can i find out what my cut off is? Like when my voltage gets too low, i believe it cuts off when the battery reaches a certain percentage. Anyone know how to check that? Thanks in advance.
go in to the p menue and volt on my scooter not zero i can adjust the cut off higher and when it cuts i have spare power to take me home like a reserve fuel tank WARNING don adjust it lower you wil have more range yes but it can damage the battery
Did you find out?
@@CarleyEspritPhilip Yah, mine was aet at 42 and the actual cut off i believe it 41, or maybe 40, u could google it to be sure, but mine is a 52 volt, and the cut off is at 42. Have fun and ride safe!!
I know this been so long ago.. Can ask why my scooter battery guide is allways 100% I mean full green bar but . I'm driving then suddenly batery empty..
How do you reset the time
I brought a this set controller but when I connect the wires( only battery wire and 3 phase wires ) "warning sign" blink and when accelator is increased "countinous speed " signs appears, any one can help me please.
Thanks for the heads up! One question when my scooter is under load the battery shows it near empty, when I release the throttle it climbs back up? Is this normal?
i can tell u that mate! when u use the throttle at 30 % battery it shows you, if u hold this acceleration u get this far . but if you now take your throttle at 70% it shows you how long u can get at 70% throttle, sorry for my bad english !!
@@husse843 Translation 3 years later = If you hold your acceleration at 100% the voltage will drop as your sucking more juice and will show you how far you can travel at 100% throttle. If you hold it at 50% throttle instead of 100%, it’ll change and calculate the new distance you can travel based upon power consumption being used from pulling down on the throttle. Lighter throttle = less juice being sucked out = more distance available to travel before battery dies.
@@modzmetropolis9558 actually there are no calculations or anything fancy, the reason the bars drop is because they are based on current voltage if you are using the throttle you are putting load which drops the voltage
Hi, i have a question, when i enter the P settings and long push the on/off button, the letter ''A'' on the bottom left changes to the letter ''d'' And I wondered what it does... so if you know please tell me :)
New batch of zero8v2? What should be default number of magnets? Based on the video it should be 30 but i receive it 28 only please confirm which is correct
I've had send the following::
P01: Backlight brightness, level 1 is the darkest, level 3 is the brightest; P01 defaults to 2
P02: mileage unit, 0: KM; 1: MILE; P02 defaults to 0
P03: Voltage level: P03 defaults to 60V
P04: Sleep time: 0, do not sleep; other numbers are sleep time, range: 1-60; unit minutes
P04 default is: 10
P05: Boost gear: 0: 3 gear mode; P05 defaults to 0
P06: Wheel diameter: unit, inch; precision: 0.1; P06 default is 11
P07: Speed measuring magnet number: range: 0-255; P07 default is 30
P08: Speed limit: Range 0-100km / h, P08 defaults to 100
P09: Zero start, non-zero start settings, 0: zero start; 1: non-zero start; P09 defaults to 0
P10: Drive mode setting 0: Power-assisted drive (The power-assisted gear determines how much power is output.
The handle is invalid).
1: Electric drive (drive through the knob, the power assist position is invalid at this time).
2: The power drive and the electric drive coexist at the same time (the electric drive is invalid in the zero-start state).
P10 defaults to 2
P11: Boost sensitivity setting P11 defaults to 3
P12: Boost start strength setting P12 defaults to 3
P13: Type setting of power magnetic disk P13 defaults to 12
P14: Controller current limit value setting Range: 1-20A P14 defaults to 12
P15: controller undervoltage value P15 defaults to 49
P16: ODO clear setting Long press the plus button for 5 seconds, ODO clear P16 default is 0
P17: 0: Disable cruise, 1: Enable cruise; Auto cruise is optional (only valid for No. 2 protocol)
P17 defaults to 0
P18: display speed proportional adjustment Range: 50% ~ 150%, P18 defaults to 100
P19: 0 gear enable bit, 0: with 0 gear, 1: without 0 gear P19 defaults to 1
P20: 0: No. 2 protocol 1: 5S protocol 2: standby 3: standby P20 defaults to 0
So the P11 is regen brake or something else?
Can you explain what p18 does? When I got my mx60 my settings were different..p18 only went upto 100.
It is possible that I accidentally programmed my LCD controller for a different scooter? All my settings have changed. Is there a way to change it back?
Many options off
hello. I have an electric scooter and it has the same display, or is it very similar. I would like to know if you could help me with a question that I have. Today when I was going to work, the scooter lost power, but when I stopped, I saw that the display and the ignition were still on, but the accelerator did not work. So I turned everything off, and turned the contact back on, but when I went to turn on the display, it doesn't respond. then at home, I was able to see and verify that the current reaches the display connector perfectly. . Is it sure that the display will be the problem? I also see that there are many models that are the same or very similar on the outside, how can I know if it will work on my scooter? Thank you
You cannot simply buy any display, they have to be synced with your controller. Go back to the person you bought from
@@FalconpevSg Thats the big problem,. since I bought it in AliExpress, and then the store stopped selling in AliExpress, so I can't use the same store that I bought the scooter.. So... if I buy one with 6 pins, and I review the cables, each one in its color... it won't work? thank you
@@Hijo-del-Chico no it’s in the software
My headlights and horn won’t does anyone know how to fix ?
Horn? There isn’t a horn function in the 10X
Hey bro, What is the configuré to E5?
If I put volt from 48 to 60 the top speed will be higher? And can it does problem to the motor? What if I change watt I will burn motor?
How i accidentally changed p07 setting. How doni undo it
So 10x when receiving out of the box it's not set yet so I have to set the controls before riding
What do to if the charger light don't turn from red to green even though the step is fully charged (i can see that on my screen and my voltage is 65. I have a 60V). Can it do damage to my battery? Thanks!
i cant put on the lights the symbol shows but no light
Your dc converter light module is damaged maybe
My screen won’t turn off via power button
Unplug and plug the lcd connector back in. Lcd could be in a bad state so not reading inputs.
Do you know how desensemble conector to wire from controller? It is view in video alltime
i need a video on how to put a electric voltage monitor on this lcd ...you already have one for the older 8 but i have the newer 8 with this controller
P-Settings are all the same on all brands as long it's QS-S4?..My eks brand is DOUBLE D VA40P also QS-S4 throttle.
Yes all the same
Where can I buy this universal LED?
Mae Aballe here you go www.falconpev.com.sg/products/zero-8-throttle?_pos=1&_sid=1d8f9ce05&_ss=r
Falcon PEV | PAB PMD E-Scooter E-Bike Shop thank you so much
i can't really hear what your saying
Sorry about that.
Hello what is the Code for Zero 10-Z ??
If I'm in eco mode, can I switch to turbo mode by pressing the turbo button or do I have to go to gear 3 first..??
Mine didn’t shoe p2 menu , why ? , helpppp😪
Sir may i ask i have a problem with my parameter, the battery indicator is blinking into a lowbat but the volt is 41v, i charge its only 3 hours then the light indicator on charger is green, but still the icon of battery is still blinking,but the scooter is working and running, i want to send a video to you but cannot here, please help me thank you.
check ur controller voltage...if 36v ....in P3...change to 36.....
p16How to be clear？
2 years ago I remember I was able to turn on "6kmh cruise" mode for my Zero 10X by pressing and holding some buttons. It was very useful when walking and pushing the scooter, but I don't remember how exactly I enabled it. Do you have any information how to enable this walking cruise mode?
Is it possible to use that lcd to gyro corp (gyro g air plus scooter)? My lcd has no display and i want it to replace that kind of lcd...tnx!
what is cruise 1 or 0???
1 is cruise control activated. simply hold down throttle for 5 seconds with the same speed to activate cruise.
How do you fix the "Error 08" in the Controller?
slow down or reduce charge current
I think someone change my P15 settings, I need to adjust it again to the factory default for P15, what's the default for Zero 10x. Thanks for the help
hope you figured it, however if its not done yet, please do send us a video through whatsapp or email at sales@falconpev.com.sg
Help: battery bar empty even when I am fully charged
What scooter do you have
Thank you, very helpful 😁
Show triangle 🔺️in meter and not move
Brake sensor activated
@@FalconpevSg how to off
Can i change cruise activation time ( p17 )? How?
What is cruise activation means or for? p17) no idea at all. Thanks
i dont think so, default its about 4-5secs.
Sabría alguien mandarme los parámetros del display del patinete Brighton 1000
Can i somehow reset the km?
do u found a solution yet?
i think he sad that p16 is gone reset it
How does the Eco/Turbo button differ from the gear select?
Hi falcon I really hope you can help me as my vendor isn't being very helpful :(
So I bought a mercane mx60. I tried to unlock the full speed and I believe I made a mistake as the settings are different now. P18 only used to go to 100, now it goes to 150.
I am wondering. Could I have accidentally programmed it for a different scooter?
Althought I have changed the speeds it feels slower and more sluggish than when I first got it and the speed (p8) was set to 35 :(
Also, sometimes when I turn it on or press buttons I get a red exclamation! And a "e" comes up then goes away.
Sometimes I set the settings and they will change on their own.
It is a really heavy scooter and now it barely moves in single motor
Please if anyone can help I would really appreciate it. Thank you
did u get a response on how u could reset the entire scooter? please help
Thanks big help
If anyone can shed some insight on how to fix error code 10 it would be greatly appreciated !
Me too! Did you figure out how to fix E10 error code? I even got a new throttle and it did not fix it
Thank you!
I messed with the programming stuff and i almost died on it. Is there any way to reset it to factory settings or something? Scooter wouldnt stop and brakes are really violent. Please help!!!
Did you do the reset?
@@DanceySteveYNWA thanks but i figured it out. I activated the electronic brake by mistake
@@ChuppyCata oh, I was going to help you with it, but if you're good, no problem. Safe riding.
My LCD don't don't turn on the power button won't work. I bought a new LCD and it still don't power on what's the problem of my zero 8x please help
Can your scooter charge?
@@FalconpevSg no it won't charge either
@@swave1234 so it’s not the lcd it’s the battery
@@FalconpevSg so my battery is broken? But I only used the scooter for 1 year
Do I need to buy new battery?
Please help
I brought my 10x from you guys So happy!!
I had a full charge on the scooter and completed a 4 mile ride and then turned it off.
I returned later the same day and turned the scooter on to find the battery Barr apparently was empty and was flashing with the red warning triangle next to it..
Thank you.
E 10
How is the Error coming along? Provide us an email for us to communicate better.
How to max Speed and Power? P12 only?
What is the default settings of (P15) for a Zero 10X?
Did you have this Settings ? Because My Controller Jas also wrong Settings
P3 = 52/ P15 = 44 is approximately 28% of battery; the manual says the Voltage 42 =15% of battery approximately. For 52v 18 ah
@@oscargomezarango9184 thanks heaps Oscar, i appreciate your help, and maybe you happened to know for 52v 23ah? cutoff voltage?
Thank you for this
So it has no blue tooth?
it has no android app?
Nope, you don’t want those as they are a huge hassle.
Is there a way to display riding time? Additional to voltage and trip distance.
what does it mean cut off voltage? and why mine set to 39? (P15)
it means the lowest battery voltage that the controller can support.
@@FalconpevSg thanks
What exactly does the high beam symbol do when hold mode button ? Is there a cable from the controller that is switched on ? If , what color and voltage ? Thx
It does nothing :)
Bonjour quels sont les meilleurs réglages pour une zero10x merci beaucoup je suis en france
Thanks for this video! When I try to get the P program menu it goes to a menu PO from there I can’t access to the program menu! Its posible that my scooter has that menu locked?
Oswaldo Hernandez where did you get your scooter from
Falcon PEV from israel! It’s another brand but the same controller (QS -S4), should I ask the seller if there is a password?
Thanks for your answer!
Dude i can barely hear you
How to enable electronic brake on x10 ? I set P11 to 0-5, all not working :(
Артем Романихин because yours is not the zero 10X
thanks for the info but is there any added setting on the Zero x11???
After you change the settings, does it automatically save or you have to readjust every time? I didn't see a save feature after you exit the settings menu at the end. Thank you for the informative video!
It saves
Could you please tell me what does it mean the exclamation mark on the left side of the lcd?
Lucy Diamond it’s nothing. It will go away after a while.