The fastest way is to just use a razor or flexible utility knife. It won't leave a messy residue and you can immediately re-apply another bead of silicone right away. the old silicone does not have to be 100% removed, just close enough so that the new silicone will have a good contact and it will adhere itself long enough until you have to replace that. Just my honest 2 cents worth. Not trying to criticize bc you have put up many useful videos on DIYs. Keep up the good work my friend.
I'm no handyman OK I've fitted a garden pond but never done anything in the bathroom . Watching this video has given me the encouragement. OK so far I haven't burn the house down... Thanks
If you plan on removing the sink and replacing, tiling, or servicing it, a strong (dacron preferred) fishing line with two dowel or stick handles can be used to cut through the silicone around the sink.
Great video, I'm literally off to a store to buy the solvent; I have a lot of it to remove given I have a leaking shower cubicle :( Fed up already of trying to remove it with a blade, which is messy, inefficient & dangerous in part (for self and surfaces). I thought there must be an easier way to do this! Am worried if water is passing beneath the L-shaped trim, on top of the shower tray & behind base of tiles & then past that & into Kitchen ceiling! Well done, saved me some work no doubt!
Yes, I use WD40 as well - it works quite well, and it means you don't have to buy another product just for this job. What do you think UltimateHandyman? How does WD40 compare to the proprietary silicone removers?
Why do you need to clean it specifically with methylated spirit afterwards? Is this to ensure any silicone remover residue doesn't attack the new silicone applied?
This is all set up. I bought same staff after watching video... left the smount of time it said on tube and to be honest all I could remove was this sillicon oldbone was still there evdn thought I used proper scraper then one on the video. Reterning item tomorrow back to the shop. Thanks for the vid
@ultimatehandyman I'll try that, thanks. Sealing over with silicone - never thought of that, I'll squirt some out first ready to apply after inserting the screw all the way in. Cheers.
Will this get deep into a tight seal? I have some ceramic objects stuck together with silicone and I need to separate them safely. Great video, thanks.
@Tanglefoot3 any method that leaves an airtight seal will work. I usually wrap the tip with duct tape so the tape extends about an inch beyond the tip of the tube. pinch the tip of the tape tube leaving an air pocket beyond the tip of caulk tube. squeeze enough caulk to fill the air pocket in the tape and will stay wet. even better though is the tubes that come with a cap. save the caps and put em on tubes you want to save. just seal it with electric tape or plumbers tape of you got it.
Thanks for all the interesting videos. Do u think the silicone remover would knacker a vinyl floor if it was to get on it? Need to get sealant from the bath panel to the floor off.
Right. Done. Now - what's the best way to clean the surface of the silicon remover? It's left a nasty oily sticky residue that doesn't seem to respond to soap and water. I need to prepare the surfaces for new silicone. Thinners? Turps? Bleach?
oops! i forgot to add--the silicone is suggested by simplehuman to mount their soap dispenser wall mount, and i would be mounting this onto tile. i don't want to ruin my tile should the dispenser fall off or if i want to get rid of it! thank you so much for any help!
Is it me or are the chemical silicone 'digesters' less effective than they used to be? I recently bought a small scraper which holds one of those single-sided razor blades, and because it's so sharp it cuts the silicone away from glazed surfaces very easily. If there's a trace of silicone left I then use some digester.
I've just seen Stuarts comment when you commented, as I don't always get notifications from TH-cam. After it has cured you could try removing it- th-cam.com/video/TZ7x6Lcml1Y/w-d-xo.html
Have you any tips for sealing your silicone tube after use? I've tried the old nail or screw in the end but it never works, even tried clingfilm. Is their any way to do this?
metaljohn209 It should be okay, but best to test it on an inconspicuous area first. Some people have recommended using a hair dryer or even WD40 to remove the silicone. That might be worth a try first?
@@ultimatehandyman thanks for great video, concise and clear. I have some sort of acrylic or fibreglass bath with ceramic tiles. Good tip re trialling in an inconspicuous location first to see if remover compatible with the bath surface. Any specific comment? Regards, Geoff
The prior owner of my sailboat must have had stock in 3M Silicon since it is everywhere. I want to remove it from the fiberglass. Will these removers damage fiberglass that you know of?
if i mount something with silicone, and the silicone is behind that which i've mounted, can i use a product to eat away at the silicone behind say, a wall mounted soap dish?!
It's quite tricky, I think there's quite a bit of silicone behind the join on the inside. I've managed a few with a thin knife but i'd prefer something less dangerous and less likely to damage the ceramics.
Hi handyman, i just watched another one of your videos where you used a no nonsense silicone remover and compared it to WD40. However it seems in this video the silicone seems to remove easier. Would you prefer this silicone remover over the no nonsense and WD40? Thanks
Don't ever put a screw or nail in a tube of caulk or silcone. It just clogs the entire nozel and you are left with a very small exit hole. Just leave and re-poke it with the poker, or you can even put tape on the end, but never use a nail or screw unless you using it within the next few days
I don't really like that silicone remover stuff; it makes the silicone gungy and difficult to remove. I've started using a flexible sharp kitchen pushed up again the wall/tile/bath and then cut it out. My 2 cents.
divoinblue I only searched these keywords because I’m looking for an angled craft scalpel essentially, what would be nice is a square and round corner version, because the surfaces are painted and not recoatable sealed to plastic, and both need to be saved
Hi there,could I use this type of remover on pvc trim on my bathroom window?I just had applied new trim around my bathroom window though thought I had removed the excess silicone & now a day later it has bonded to the new trim,I was wanting to just apply to overrun areas not the actual seams being I want to leave that in place what do you recommend? thank you...
My girl used black silicone to put some wind visors on the car but the silicone is now glued to the window molding you think if I use this to removeit, it wild damage the window molding? ???? Sorry for my bad English
Joshua Reyes It should be okay, but best to test it first. Some people have suggested using a hair dryer to soften the silicone or even WD40 so there are other options ;-) I hope this helps, your English is not at all bad by the way ;-)
Some people have suggested using a heat gun, but I have not tried it myself. WD-40 works on some silicone's but you need to clean any residue off with methylated spirits before re-applying the silicone. Thanks for the comment 👍
Actually I did find a product that will take off silicone residue and won't harm a vinyl floor. It's called Re-mov and I found it at a site called Silkote in Canada. They say they ship worldwide so you might want to give them a try. The site is silkote.com and then click on re-mov.
David Craig It should be, but you should test a small area first. I have used this around baths with no problems at all. th-cam.com/video/DKFunUIh9rc/w-d-xo.html Sorry for the late reply, this comment was in the spam collector!
Go to the upvc window store and buy a container of upvc solvent silicon re mover , works in no time ans it,s not expensive ... it will clean without damaging PVC windows ... that what it was made for .. cost about £4 .... I'm a painter and use it most days
Yes, back in the 1940's people used to have common sense and money was expensive. Back then people used to prefer to pay 2 pence for a rubber washer, rather than £10+ for a ceramic cartridge. Now money is cheap and some people would rather pay £10+ to repair a tap rather then 2 pence, because many of them are paying with money that they have not earned yet ;-)
if you need instant results, well shorter than 3 to 20 hours, i recommend using WD40, no disrespct to you ultimate handyman. As loads of your other vids have helped me out, just thought i'd return the favour................smily face
..............sorry, for that i have no answer, wait on, try putting the clothing into your freezer and when it freezes, see if the silicone snaps away........hope that helps...?
I have never tried it but do not think it would be good as it is petroleum based and could leave a residue behind which will interfere with the new application of silicone.
A friend/neighbour used this product to remove silicone sealant in their kitchen, to their horror it damaged the worktop surface. I know they should have read the instructions before using. Apparently it can also damage plastic baths, so use with caution.
+Cliff Carlo I tend to just use the screwfix own brand now as it seems to do a good job and has been safe to use on everything I have tried it on so far. Always best to check though before using it. Thanks for the comment ;-)
Hi UH I have a crack/split in a couple of my freezer drawers. Could you recommend a product that would repair these slits/crack and obviously be capable of withstanding such low and constant low temperatures. Thanks in advance Cliff
WD40 will do it, but make sure you clean afterwards thoroughly with methylated spirit to remove any traces of WD40... Once dry, reseal with new sealant using a Fuji kit...
+Ultimate Handyman Thanks for getting back to me so quickly. Do you know roughly how long it takes for the sealant to 'set' (if that's the right word!) well enough for the bath & shower to be usable?
Great video but the stuff we used that purported to remove the silicone wasn't nearly as good. You practically needed an atomic bomb to get rid of the silicone sealer in our shower surround.
I have only tried two different makes and both worked fine. I guess the quality of the silicone used and the age of the silicone can affect the ease of removal!
Rich Housley @ Could you please confirm that WD-40 removes the silicone sealant from glass as well? I have to clean silicone sealant spots from my aquarium glass... If you could reply me ASAP that would be great.. thanks in advance...
....between 3 and 20 hours?!!! Lol. Life's too short for that carry on, Bud. Razor blade is your friend...yeah, it's a bit of graft, but you can do another job in the morning instead of coming back to this one.
I don't normally just wake up one day and think "I know I'll replace the silicone around my basin/shower", I normally plan it a few weeks in advance, then apply the remover the day before.
spray some WD40 over the silicon...It will loosen up and pull away on its own...It can be done in 1/2 hour or so.. much cheaper, faster and cleaner....no damage to the surfaces either.
@@ultimatehandyman Sorry matey - Didn't mean to sound rude. I meant as a handyman trying to get a job done quickly. The customer always want me in and out before the family gets home and its not ideal to have chemicals soaking around the bathroom sink over night especially when kids are at home. I find it best to cut back as much silicone as possible and apply a product that may take 30-60 minutes max to do the business. I've found nothing spectacular yet, and still relying on good, old-fashioned elbow grease. Thanks for the videos - I think they are brilliant and have helped me massively over the years. Best wishes. S
No worries, I did not think you were being rude at all 👍 I think a lot depends on the exact chemical makeup of the silicone. I have had some that is very difficult to remove and nothing touched it- apart from a sharp knife. Yeah, if you are doing this for someone else, I can see the problem! Thanks for watching the videos, best wishes for Christmas and the new year 👍
Mixer taps (faucets) are available in the UK but to be honest they are more trouble than they are worth. They are difficult to service and noisy! If you open a single tap there is hardly any noise but with a mixer tap you tend to find that they are noisy (especially if you get up early for work). All the taps in my new house are mixers and they are all noisy ;-) Thanks for the comment
Ozzy Dea The left tap should actually be hot and the right tap should be cold. If the hot tap is providing water that is too hot there is a special thing on the boiler called a thermostat, which can be used to turn the hot water temperature down ;-)
This is just what I have to do in the kitchen. I am from Mexico and I hope getting this silicone sealant remover would be easy. Thank you so much.
The fastest way is to just use a razor or flexible utility knife. It won't leave a messy residue and you can immediately re-apply another bead of silicone right away. the old silicone does not have to be 100% removed, just close enough so that the new silicone will have a good contact and it will adhere itself long enough until you have to replace that. Just my honest 2 cents worth. Not trying to criticize bc you have put up many useful videos on DIYs. Keep up the good work my friend.
I'm no handyman OK I've fitted a garden pond but never done anything in the bathroom . Watching this video has given me the encouragement. OK so far I haven't burn the house down... Thanks
If you plan on removing the sink and replacing, tiling, or servicing it, a strong (dacron preferred) fishing line with two dowel or stick handles can be used to cut through the silicone around the sink.
Great video, I'm literally off to a store to buy the solvent; I have a lot of it to remove given I have a leaking shower cubicle :( Fed up already of trying to remove it with a blade, which is messy, inefficient & dangerous in part (for self and surfaces). I thought there must be an easier way to do this! Am worried if water is passing beneath the L-shaped trim, on top of the shower tray & behind base of tiles & then past that & into Kitchen ceiling! Well done, saved me some work no doubt!
Yes, I use WD40 as well - it works quite well, and it means you don't have to buy another product just for this job. What do you think UltimateHandyman? How does WD40 compare to the proprietary silicone removers?
Why do you need to clean it specifically with methylated spirit afterwards?
Is this to ensure any silicone remover residue doesn't attack the new silicone applied?
This is all set up. I bought same staff after watching video... left the smount of time it said on tube and to be honest all I could remove was this sillicon oldbone was still there evdn thought I used proper scraper then one on the video. Reterning item tomorrow back to the shop. Thanks for the vid
@ultimatehandyman I'll try that, thanks. Sealing over with silicone - never thought of that, I'll squirt some out first ready to apply after inserting the screw all the way in. Cheers.
So satisfying to see it scrape-off so easily
Absolutely!
Thanks for the comment
Will this get deep into a tight seal? I have some ceramic objects stuck together with silicone and I need to separate them safely. Great video, thanks.
@Tanglefoot3 any method that leaves an airtight seal will work. I usually wrap the tip with duct tape so the tape extends about an inch beyond the tip of the tube. pinch the tip of the tape tube leaving an air pocket beyond the tip of caulk tube. squeeze enough caulk to fill the air pocket in the tape and will stay wet. even better though is the tubes that come with a cap. save the caps and put em on tubes you want to save. just seal it with electric tape or plumbers tape of you got it.
Thanks for all the interesting videos. Do u think the silicone remover would knacker a vinyl floor if it was to get on it? Need to get sealant from the bath panel to the floor off.
Hey, great video, why are you using silicone gloves?
Right. Done. Now - what's the best way to clean the surface of the silicon remover? It's left a nasty oily sticky residue that doesn't seem to respond to soap and water. I need to prepare the surfaces for new silicone. Thinners? Turps? Bleach?
The stuff I used just wiped away!
I'd try methylated spirits first if soap and water is not working.
oops! i forgot to add--the silicone is suggested by simplehuman to mount their soap dispenser wall mount, and i would be mounting this onto tile. i don't want to ruin my tile should the dispenser fall off or if i want to get rid of it! thank you so much for any help!
Is it me or are the chemical silicone 'digesters' less effective than they used to be? I recently bought a small scraper which holds one of those single-sided razor blades, and because it's so sharp it cuts the silicone away from glazed surfaces very easily. If there's a trace of silicone left I then use some digester.
I'm not sure, as I have not used any for a while!
Thanks for the comment
Hi ultimate handyman, great vid, How long after placing the small bead behind the taps did you leave it before applying the big bead over the top..?
I can't remember now, sorry as this was done years ago.
I'm sure I would have waited until the sealant had just started to harden.
Ultimate Handyman ok thank you
Great video as normal, thanks fir them all I have learnt so much.
Thanks for the WD40 tip just tried it out and it worked a treat.
I have just fitted a new black kitchen sink and I have got some silicone sealer on the surface, any suggestions for removing it.
Thanks
I did the same thing, did you get any answers?
Sorry, I have just seen this comment now.
You could try silicone remover- th-cam.com/video/TZ7x6Lcml1Y/w-d-xo.html
I've just seen Stuarts comment when you commented, as I don't always get notifications from TH-cam.
After it has cured you could try removing it- th-cam.com/video/TZ7x6Lcml1Y/w-d-xo.html
is this applicable on aquarium silicon
plz do inform me
Have you any tips for sealing your silicone tube after use? I've tried the old nail or screw in the end but it never works, even tried clingfilm. Is their any way to do this?
Is this ok to put on a RV roof that is made out of EPDM or TPO roofs?Can it go on the siding of the RV as well?
metaljohn209
It should be okay, but best to test it on an inconspicuous area first.
Some people have recommended using a hair dryer or even WD40 to remove the silicone. That might be worth a try first?
@@ultimatehandyman thanks for great video, concise and clear. I have some sort of acrylic or fibreglass bath with ceramic tiles. Good tip re trialling in an inconspicuous location first to see if remover compatible with the bath surface. Any specific comment? Regards, Geoff
@mobilove no problem, hope it worked for ya.
The trouble with using WD-40, which is very effective, is that even trace amounts prevent the new silicone from bonding well.
That is correct. I normally use methylated spirits to clean the area after removing silicone.
Thanks for the comment
thank you ultimate handyman. you're awesome! now i will mount my soap dispenser without fear : )
I use hair-dryer. It is quick, cheap and environment friendly
Thanks for the comment
Which brand is your silicone remover? I bought one and I'm allergic to that one...
The prior owner of my sailboat must have had stock in 3M Silicon since it is everywhere. I want to remove it from the fiberglass. Will these removers damage fiberglass that you know of?
How do you know if what you want to remove is silicone based?
if i mount something with silicone, and the silicone is behind that which i've mounted, can i use a product to eat away at the silicone behind say, a wall mounted soap dish?!
Hi, I have a spot on my home on painted stucco where apparently someone caulked an area with silicone. Would this work to remove it?
It's quite tricky, I think there's quite a bit of silicone behind the join on the inside. I've managed a few with a thin knife but i'd prefer something less dangerous and less likely to damage the ceramics.
Hi handyman, i just watched another one of your videos where you used a no nonsense silicone remover and compared it to WD40. However it seems in this video the silicone seems to remove easier. Would you prefer this silicone remover over the no nonsense and WD40? Thanks
I'd use the silicone remover, as some people have had problems when re-applying silicone after using WD-40
Thanks for the comment
Don't ever put a screw or nail in a tube of caulk or silcone. It just clogs the entire nozel and you are left with a very small exit hole. Just leave and re-poke it with the poker, or you can even put tape on the end, but never use a nail or screw unless you using it within the next few days
I don't really like that silicone remover stuff; it makes the silicone gungy and difficult to remove. I've started using a flexible sharp kitchen pushed up again the wall/tile/bath and then cut it out. My 2 cents.
divoinblue I only searched these keywords because I’m looking for an angled craft scalpel essentially, what would be nice is a square and round corner version, because the surfaces are painted and not recoatable sealed to plastic, and both need to be saved
Plus who wants to wait 24 hours?
would this product damage a laminate kitchen worktop ?
What about on painted or plastic surfaces?
Hi there,could I use this type of remover on pvc trim on my bathroom window?I just had applied new trim around my bathroom window though thought I had removed the excess silicone & now a day later it has bonded to the new trim,I was wanting to just apply to overrun areas not the actual seams being I want to leave that in place what do you recommend? thank you...
You could try the silicone remover. Some people have suggested WD40, so it might be worth trying that first
My girl used black silicone to put some wind visors on the car but the silicone is now glued to the window molding you think if I use this to removeit, it wild damage the window molding? ???? Sorry for my bad English
Joshua Reyes
It should be okay, but best to test it first.
Some people have suggested using a hair dryer to soften the silicone or even WD40 so there are other options ;-)
I hope this helps, your English is not at all bad by the way ;-)
Thanks.
@Tanglefoot3 ha! oops, didnt notice you posted this 5 months ago. guessing you figured it out by now...
What's the easiest way to remove silicone from interior windows the walls are on the Lake?
Some people have suggested using a heat gun, but I have not tried it myself. WD-40 works on some silicone's but you need to clean any residue off with methylated spirits before re-applying the silicone.
Thanks for the comment 👍
Interesting......
beautiful video
Thanks for the comment
Actually I did find a product that will take off silicone residue and won't harm a vinyl floor. It's called Re-mov and I found it at a site called Silkote in Canada. They say they ship worldwide so you might want to give them a try. The site is silkote.com and then click on re-mov.
does the silicone remover damage paint?
Handy stuff, saves a lot of work.
Can I use this to melt CDI unit of bike?
No, I don't think so.
Thanks for the comment 👍
will WD40 (used to remove silicone) harm brick or mortar wall ... will silicone sealant remover harm brick or mortar?
I have heard that WD-40 can cause problems when re-applying the new silicone.
The silicone remover should be ok though.
Is this safe to do with plastic tiles and shower doors?
David Craig It should be, but you should test a small area first. I have used this around baths with no problems at all.
th-cam.com/video/DKFunUIh9rc/w-d-xo.html
Sorry for the late reply, this comment was in the spam collector!
thank you.
David Craig You are welcome
can i get this stuff in canada?
This was really helpful. Thanks very much.
Go to the upvc window store and buy a container of upvc solvent silicon re mover , works in no time ans it,s not expensive ... it will clean without damaging PVC windows ... that what it was made for .. cost about £4 .... I'm a painter and use it most days
Ill be trying this
Glue remover ?
Separate taps for hot and cold water? Was this video sent from the 1940's?
Yes, back in the 1940's people used to have common sense and money was expensive. Back then people used to prefer to pay 2 pence for a rubber washer, rather than £10+ for a ceramic cartridge. Now money is cheap and some people would rather pay £10+ to repair a tap rather then 2 pence, because many of them are paying with money that they have not earned yet ;-)
***** I bet you have two different shower heads too, and you alternate really quickly between the hot and the cold? :-)
Bla bla bla, write something useful, you need a job you are bored :-(
Well said that man. I'd bet the Jaakko chap is young cocky and unable to spell his name right.
Nick Pearce
I'd very much like to be young but unfortunately I'm 48 years old.
if you need instant results, well shorter than 3 to 20 hours, i recommend using WD40, no disrespct to you ultimate handyman. As loads of your other vids have helped me out, just thought i'd return the favour................smily face
Not tried WD40 yet, I'll test it when I get chance ;-)
Thanks for the comment
How do you get silicon out of clothing?
..............sorry, for that i have no answer, wait on, try putting the clothing into your freezer and when it freezes, see if the silicone snaps away........hope that helps...?
off to try this :-) thanks (I think)
David Harber Most sealants have anti-frost guard. So it may not help by putting clothing in the freezer.
Top man, great advice.
@ultimatehandyman
thanks for the advice!
Can anyone advise how to remove WD40 before re applying Silicone?
Methylated spirits and paper towels works well.
Metho, acetone.
Eucalyptus oil softens silastic to a snot too.
Ultimate Handyman can I use white spirit instead of methylated?
I have never tried it but do not think it would be good as it is petroleum based and could leave a residue behind which will interfere with the new application of silicone.
dunno
tar and glue remover does the same thing
Sharp blade works well at removing the majority. For stubborn bits that remain, I've had good results with steel wool
Thanks for the comment
I never know about the WD40. Thank you!
Thnks sir for ur good infor.....
Daya Rao
You are welcome
Thanks for the comment
great simple to follow tips :)
Thanks for the info, drop in for a cold one when in Canada next
A friend/neighbour used this product to remove silicone sealant in their kitchen, to their horror it damaged the worktop surface. I know they should have read the instructions before using. Apparently it can also damage plastic baths, so use with caution.
+Cliff Carlo
I tend to just use the screwfix own brand now as it seems to do a good job and has been safe to use on everything I have tried it on so far.
Always best to check though before using it.
Thanks for the comment ;-)
Hi UH
I have a crack/split in a couple of my freezer drawers. Could you recommend a product that would repair these slits/crack and obviously be capable of withstanding such low and constant low temperatures.
Thanks in advance
Cliff
+Cliff Carlo
I'm not sure to be honest as I'm no expert on plastics.
Perhaps supa-fix will work- th-cam.com/video/pS3vX8q00OM/w-d-xo.html
I thought if anybody knew, it would be you. Thanks for being honest.
What about on wood?
You would have to test it I'm afraid.
What is it's chemical name
No idea, sorry.
Great video, thank you!
WD40 will do it, but make sure you clean afterwards thoroughly with methylated spirit to remove any traces of WD40... Once dry, reseal with new sealant using a Fuji kit...
Thanks for the comment 👍
excellent stuff
thanks .. and i thought u sounded like sir alex ferguson !
😂
Great vid.
Wonder if this as good as paintstripper which is about as usefull as a chocalate teapot!!!
perfect
Thanks for the comment
oh, yea
Thanks for the tip.
@LetsGoFlyers2011
thanks for the advice!
lol from the thumbnail picture I thought he was going to use toothpaste to remove it.
@jsage5 haha i do it all the time, it lasts months!!!
but thanks for the tip
I want this product! :o
It makes life so much easier ;-)
thanks
I saw elsewhere that WD40 is as good as any other remover - can anyone verify this?
+Ed Barrett I have not tried it yet, sorry.A few people have said that it works though!
+Ultimate Handyman Thanks for getting back to me so quickly.
Do you know roughly how long it takes for the sealant to 'set' (if that's the right word!) well enough for the bath & shower to be usable?
+Ed Barrett Best to leave it till the next day really. It's not worth risking ruining your work by showering in the area too early.
+Ultimate Handyman Thanks for the advice.
Yes it works and is faster than this crap.
excellent,,,thanks
You are welcome.
Thanks for the comment
Great video but the stuff we used that purported to remove the silicone wasn't nearly as good. You practically needed an atomic bomb to get rid of the silicone sealer in our shower surround.
I have only tried two different makes and both worked fine. I guess the quality of the silicone used and the age of the silicone can affect the ease of removal!
Oh my goodness! It just comes off as though it was a strip of putty!! I am sitting here in shock!
Yes, sometimes it works really well- it does depend on the silicone though.
Thanks for the comment
You don't even need use unibond silicone remover . Wd40 work's just as good .and is much quicker
Thanks, I'll try it ;-)
Rich Housley @ Could you please confirm that WD-40 removes the silicone sealant from glass as well? I have to clean silicone sealant spots from my aquarium glass... If you could reply me ASAP that would be great.. thanks in advance...
If you use the wd40 and not the cheap crap
rich housley thank you very much rick for your quick reply... I will use WD40 to clean my aquarium glass to remove silicone sealant spots... :-)
perfect ❤❤
Thanks for the comment
....between 3 and 20 hours?!!! Lol. Life's too short for that carry on, Bud. Razor blade is your friend...yeah, it's a bit of graft, but you can do another job in the morning instead of coming back to this one.
I don't normally just wake up one day and think "I know I'll replace the silicone around my basin/shower", I normally plan it a few weeks in advance, then apply the remover the day before.
Ultimate Handyman...... Fair point :o)
Thanks for the comments ;-)
This works, great tip! oooooO.Oooooo
Thanks for the comment
Thanks for the video, it was really useful for me!
why don't you use a utility knive ...
Some people are stupid, I don't want to show them something that they might copy that has the potential to cause injury.
Omg!
spray some WD40 over the silicon...It will loosen up and pull away on its own...It can be done in 1/2 hour or so.. much cheaper, faster and cleaner....no damage to the surfaces either.
+chitpaul singh kallah I'll try this out when I get chance ;-)
You know I'm going to try WD40
+TheAudiostud
I'm going to try it too in future ;-)
+TheAudiostud did you the WD40?
+Ray H I'm going to be remodelling my bathroom in the summer, I will update the effectiveness of WD40 when I remove the bath & sink
Who the hell gad 3-24hrs when trying to get a job done!?
Most homeowners 😉
@@ultimatehandyman Sorry matey - Didn't mean to sound rude. I meant as a handyman trying to get a job done quickly. The customer always want me in and out before the family gets home and its not ideal to have chemicals soaking around the bathroom sink over night especially when kids are at home. I find it best to cut back as much silicone as possible and apply a product that may take 30-60 minutes max to do the business. I've found nothing spectacular yet, and still relying on good, old-fashioned elbow grease. Thanks for the videos - I think they are brilliant and have helped me massively over the years. Best wishes. S
No worries, I did not think you were being rude at all 👍
I think a lot depends on the exact chemical makeup of the silicone. I have had some that is very difficult to remove and nothing touched it- apart from a sharp knife.
Yeah, if you are doing this for someone else, I can see the problem!
Thanks for watching the videos, best wishes for Christmas and the new year 👍
Stop using 2 separate faucets! That is just pure madness! How do you wash your hands? A "mixer" is such an easy system, so why not use em?!?!?!
Mixer taps (faucets) are available in the UK but to be honest they are more trouble than they are worth. They are difficult to service and noisy! If you open a single tap there is hardly any noise but with a mixer tap you tend to find that they are noisy (especially if you get up early for work). All the taps in my new house are mixers and they are all noisy ;-) Thanks for the comment
Ozzy Dea
The left tap should actually be hot and the right tap should be cold. If the hot tap is providing water that is too hot there is a special thing on the boiler called a thermostat, which can be used to turn the hot water temperature down ;-)
Ozzy Dea 'Amish of Europe''..wtf!. bit of a sweeping statement there.. Why don't you just say ''I hate British people''..:/
You know what? I have no idea what you mean about the mixer being "noisy." We use them all the time, no more noisy than a double...
Ozzy Dea Awe rentagob Ozzy is back. Look at me I think I know everything LOL. We are having a great laugh at your big mouth!!
Cool
uh?
From 3-20 hours !!!!!
I don't make the stuff ;-)
Obviously this is ideal for use at home but no good for tradesmen.
Thanks for the comment
WD40 mate.
Thanks. I have filmed a comparison between the two and will upload it soon ;-)