My car's speed sensor has a problem and a DTC appears after scanning. I have tried replacing the sensor with a new sensor, but the problem is not resolved because if the engine is running the check engine light comes on and if it goes 10/20 meters the check engine light goes off. but if you stop check the engine starts again. the car feels heavy when driving.. what steps do I need to take? if the cable is safe and not broken.
i replaced wheel speed sensors all brakes abs light comes on and brake light and then wont shift think one new part is bad ? anything would help me thank ypu
That more than likely would be a solenoid issue. Or simply changing your trans fluid and filter if the problem continues go to a professional I promise
Can the vehicle speed sensor makemy 09 Impala only start out in first or 2nd gear I can shift it manually but it won't start out in drive or od,I just had a transmission put in from a salvage yard and the transmission was missing a vehicle speed sensor so the mechanic put the one from my old junk transmission onto the one know.
Yes, it can cause issues with the TCM when shifting the transmission, but several things can cause the same issue. Usually, there is a speed sensor code such as P0500.
@@HVAC_Mechanic ok I got to get it scanned the mechanic didn't have one,shifts ik but who wants to shift it manually,.will it hurt it driving like that
I have 07 Nissan Murano SL . Speedometer jumping and acting funny also no communication between engine and transmission . shifting delay and i cant even pass vehicle so what should i replace the input or the output and the location of the sensor please . i appreciate any help
I got a 2002 Honda accord automatic and it shifts rough 1st nd 2nd gear and also jerks/jumps when going from park to drive or reverse only wen moving to drive or reverse it jerks/jumps and also when coming to stop it jerks/jump no check engine but the abs light is on cruise control doesn’t work either would appreciate the help
thank you i have 2004 pathfinder le 6 cyl i am going to change speed sensor drivers side hope this will fix problen my speedometor and wont drive unless i relearn been without a car for mo's hope this wors
My 93 4runner has been shifting late and hard for a while. This morning Speedo went out and CEL came on. Hope a replacement of speed censor clears up all of these issues! Good video, thanks!
Tried replacing both speed sensors, Speedo issue is gone but no help with shifting. Reset ECU and codes are now for shift solenoids #2, #4 and TCC solenoid. Pulled the old ones out. They ohm good but TCC solenoid fails to actuate when power applied. All 4 solenoids are on order should arrive tomorrow or Monday.
broke my speed sensor in accident , Abs, brake, tire pressure lights on everything works & drives perfectly, is it safe to drive untill new sensor is delivered ??? 2014 toyota camry
What if I’m not getting any codes but my car is having trouble going in to gears when I’m going 40mph and the speedometer tells me a different speed and my cruise control won’t activate on 50+mph. Could it still be the speed sensor?
P0700 is a generic code the computer sends out when there is a transmission issue. Usually, there is other codes that point to the cause. I made a video on this here is a link. th-cam.com/video/SB1OptyqylA/w-d-xo.html
Hi. I have a lexus rx 350 2008 model. I had been getting intermittent CEL with a pending code p0717 (turbine shaft input speed sensor No circuit). I took it to a transmission shop. They said it’s issue with sensor and they replaced it. No there is no code or check engine light but car is driving very heavy. Car delays shifting at second gear at low rpm and while making a stop it makes a jerk and clucky sound while its downshifting-to low gears. Can you provide any input regarding this. Thanks
What would make a 2001 Chevy?S10 pickup not have third or fourth gear.It has first second in reverse.Please comment back with love to now.Thank you for this video
Just had a p0500 on my 2012 corolla, The speedometer stopped working while driving and abs and power steering shut off. Now the p0500 makes sense, But why did my battery light come on then start flashing then disappear? I cleared the code but i will be doing tests on every single one of these sensors, Hopefully no rats chewed through it. I will be using my autel to read each sensor and also so some simple multimeter readings
I have a 93 jeep xj the speed sensor needed changing, the gauge needle was bouncing and misreading the speed. however, I had to buy an aftermarket one and the wiring harness was different with no color-coded wires (all black) after hooking the wires in the order that seemed correct, I tested it out, nothing happened the gauge needle didn't move at all. My question is, if I mixed up the wiring, could I have blown a fuse somewhere and also, I unplugged the sensor harness since I don't if the wiring is correct, now my check engine came on could this be due to the speed sensor wiring is disconnected?
I have a flashing D light scanned it and it was pointing towards to solenoid sensor, I replaced it n the car still not shifting from 1st gear. Hopefully if I change the speed sensor my issue will be resolved😢
I have a 96 f 150 ( 5 speed manual ) the fuse blows I unhooked the plug that goes into the speedometer and still blows so its in the wiring of circuit. Can a bad speed sensor be the problem ?
I just purchased a 2013 Nissan Marano sport, utility vehicle. And when you put it in drive, it will not go anywhere. Nor will it let you accelerate when you put it in. Reverse the same thing happens. However, when you put it in park on neutral, you can accelerate and everything works. Could that be a Faulty speed sensor
im trying to separate the functions and locations of certain issues. i have to determine if i fried my vehicle dynamic control module (VDC) which comes as one piece mounted to the ABS pump (part# 27596FJ190); or, if i just damaged the wheel speed sensor (VSS). i installed new bearings, and knuckles for a slightly later manufacture date. my lights all came on and the car was in limp mode- couldnt even get up to 1k rpm; car was limiting speed through rpm's. I drive a standard, so i shifted to 2dn, and then 3rd gear in that almost-idling state. once in 3rd gear, all the lights that were on in the dash (ABS, hill assist, cruise control, traction control, check engine), blink on and off a few times, then stay on, as the car now comes out of limp mode- but all the lights are stuck on. cleared codes, lights came back, replaced bearings, cleared codes again, lights came back, replaced knuckles, now the codes wont clear with the various scanners. one code is P0500 (WSS A is bad), and the other is U0122 (lost comm's with VDC module). both are permanent. ABS pump comes with a silicone-sealed VDC module...$1600. both codes are permanent.
Scan for OBDII codes, which will give a speed sensor code if one is bad. If you don't have an OBDII scan tool, automotive stores often come out and scan for free.
I changed the speed sensor, didn't stop the speedometer from jumping. changed the dash speedometer, didn't work, had wires to sensor worked on, didn't work. What else could it be?
Not sure if this is relevant or not, but try disconnecting the negative post from the battery and wait a few minutes then reconnect and go for your test drive
Hi my name is Carlos I have a 2000 celiica GTS CHECK ENGINE LIGHT IS ON . WON'T GO INTO 4TH GEAR . SHOULD I BUY THE SENSOR FROM THE DELLER OR SOULD I BUY IT from auto part store? Any advice please 🙏 Hightly apriciate. .
Thank you
Great videos man!!! Absolutely love em. God bless you!!!
My car's speed sensor has a problem and a DTC appears after scanning. I have tried replacing the sensor with a new sensor, but the problem is not resolved because if the engine is running the check engine light comes on and if it goes 10/20 meters the check engine light goes off. but if you stop check the engine starts again. the car feels heavy when driving.. what steps do I need to take? if the cable is safe and not broken.
i replaced wheel speed sensors all brakes abs light comes on and brake light and then wont shift think one new part is bad ? anything would help me thank ypu
Do you have a scan tool that reads ABS codes. The codes will help to point to the issue.
If this sensor is bad, could it cause no reverse?
That more than likely would be a solenoid issue. Or simply changing your trans fluid and filter if the problem continues go to a professional I promise
Can the vehicle speed sensor makemy 09 Impala only start out in first or 2nd gear I can shift it manually but it won't start out in drive or od,I just had a transmission put in from a salvage yard and the transmission was missing a vehicle speed sensor so the mechanic put the one from my old junk transmission onto the one know.
Yes, it can cause issues with the TCM when shifting the transmission, but several things can cause the same issue. Usually, there is a speed sensor code such as P0500.
@@HVAC_Mechanic ok I got to get it scanned the mechanic didn't have one,shifts ik but who wants to shift it manually,.will it hurt it driving like that
Did you get it scanned ?
👍🏻
I have 07 Nissan Murano SL . Speedometer jumping and acting funny also no communication between engine and transmission . shifting delay and i cant even pass vehicle so what should i replace the input or the output and the location of the sensor please . i appreciate any help
Too much said, but the title says also "how to test the sensor" and it is not shown....
My car doesnt exceed 100mph while its maximum speed is 180mph why cant go above 100mph? Scanning for any trouble codes no any codes.😂😂😂
I got a 2002 Honda accord automatic and it shifts rough 1st nd 2nd gear and also jerks/jumps when going from park to drive or reverse only wen moving to drive or reverse it jerks/jumps and also when coming to stop it jerks/jump no check engine but the abs light is on cruise control doesn’t work either would appreciate the help
Finally someone actually talking
thank you i have 2004 pathfinder le 6 cyl i am going to change speed sensor drivers side hope this will fix problen my speedometor and wont drive unless i relearn been without a car for mo's hope this wors
My 93 4runner has been shifting late and hard for a while. This morning Speedo went out and CEL came on. Hope a replacement of speed censor clears up all of these issues! Good video, thanks!
Any luck
Tried replacing both speed sensors, Speedo issue is gone but no help with shifting. Reset ECU and codes are now for shift solenoids #2, #4 and TCC solenoid. Pulled the old ones out. They ohm good but TCC solenoid fails to actuate when power applied. All 4 solenoids are on order should arrive tomorrow or Monday.
broke my speed sensor in accident , Abs, brake, tire pressure lights on everything works & drives perfectly,
is it safe to drive untill new sensor is delivered ???
2014 toyota camry
Just drive it and pretend you own a VW.😢😂
What if I’m not getting any codes but my car is having trouble going in to gears when I’m going 40mph and the speedometer tells me a different speed and my cruise control won’t activate on 50+mph. Could it still be the speed sensor?
Usually, a code is given at some point. It needs to be diagnosed, but, if possible, check the fluid is at the right level and not dirty.
Hello there. How’s bout P0700 i have that code just one code P0700 what’s you think is the problem
P0700 is a generic code the computer sends out when there is a transmission issue. Usually, there is other codes that point to the cause. I made a video on this here is a link. th-cam.com/video/SB1OptyqylA/w-d-xo.html
Can you please help me with something?
Hi. I have a lexus rx 350 2008 model. I had been getting intermittent CEL with a pending code p0717 (turbine shaft input speed sensor No circuit). I took it to a transmission shop. They said it’s issue with sensor and they replaced it. No there is no code or check engine light but car is driving very heavy. Car delays shifting at second gear at low rpm and while making a stop it makes a jerk and clucky sound while its downshifting-to low gears. Can you provide any input regarding this. Thanks
Thank you this was a great help
What would make a 2001 Chevy?S10 pickup not have third or fourth gear.It has first second in reverse.Please comment back with love to now.Thank you for this video
Just had a p0500 on my 2012 corolla, The speedometer stopped working while driving and abs and power steering shut off. Now the p0500 makes sense, But why did my battery light come on then start flashing then disappear? I cleared the code but i will be doing tests on every single one of these sensors, Hopefully no rats chewed through it. I will be using my autel to read each sensor and also so some simple multimeter readings
I have a 93 jeep xj the speed sensor needed changing, the gauge needle was bouncing and misreading the speed. however, I had to buy an aftermarket one and the wiring harness was different with no color-coded wires (all black) after hooking the wires in the order that seemed correct, I tested it out, nothing happened the gauge needle didn't move at all. My question is,
if I mixed up the wiring, could I have blown a fuse somewhere and also, I unplugged the sensor harness since I don't if the wiring is correct, now my check engine came on could this be due to the speed sensor wiring is disconnected?
My 05 Subaru outback and showing er 55
Good shit bro thanks this helped 🙏🏽
What problems were you having
Can you please make a video of the location of the transmission speed sensor Toyota rav4 2003
hello my firend i have the same code p0500 in megane 2 1.6 16v automatic transmission but i dont know where is the sensor pla help me
I have a flashing D light scanned it and it was pointing towards to solenoid sensor, I replaced it n the car still not shifting from 1st gear. Hopefully if I change the speed sensor my issue will be resolved😢
P1700 on a 98 4Runner…reads 690-700 ohms from the senor. Should it read 1500-2000 ohms? Thank you!
great video
I have a 96 f 150 ( 5 speed manual ) the fuse blows I unhooked the plug that goes into the speedometer and still blows so its in the wiring of circuit. Can a bad speed sensor be the problem ?
I just purchased a 2013 Nissan Marano sport, utility vehicle. And when you put it in drive, it will not go anywhere. Nor will it let you accelerate when you put it in. Reverse the same thing happens. However, when you put it in park on neutral, you can accelerate and everything works. Could that be a Faulty speed sensor
If it's not the AWD model, might be a good idea to look into the torque converter.
I got a rebuilt cluster and everything works but the speedometer, my transmission runs fine idk if I need to replace the speed sensor or not
my cruise will come on at first then depends how hot it is before it cuts off and wont work again until i cut my car off and start it again. any idea?
I’m having the solenoid D stuck or off position problem already replaced it tho. So idk what it could be
You forgot to mention speed sensors on the rear diff
im trying to separate the functions and locations of certain issues. i have to determine if i fried my vehicle dynamic control module (VDC) which comes as one piece mounted to the ABS pump (part# 27596FJ190); or, if i just damaged the wheel speed sensor (VSS). i installed new bearings, and knuckles for a slightly later manufacture date. my lights all came on and the car was in limp mode- couldnt even get up to 1k rpm; car was limiting speed through rpm's. I drive a standard, so i shifted to 2dn, and then 3rd gear in that almost-idling state. once in 3rd gear, all the lights that were on in the dash (ABS, hill assist, cruise control, traction control, check engine), blink on and off a few times, then stay on, as the car now comes out of limp mode- but all the lights are stuck on. cleared codes, lights came back, replaced bearings, cleared codes again, lights came back, replaced knuckles, now the codes wont clear with the various scanners. one code is P0500 (WSS A is bad), and the other is U0122 (lost comm's with VDC module). both are permanent. ABS pump comes with a silicone-sealed VDC module...$1600. both codes are permanent.
Need help with a honda civc 2012 Ex speend sensor solenoid
Can you tell me how to reset the speed sensor after installing the new one?? Hope you can help
It shouldn't need to be reset. If the sensor is replaced, the code is cleared; if it comes back, there is another issue, likely the wiring.
👍
Nice video
At the very least you would explain how to test the wires /connector with a multimeter . This was click bait
I made a full video on how to test the speed sensors with a meter. Here is a link: th-cam.com/video/ZNnOfOMMjgs/w-d-xo.htmlsi=71PHVFnOmrJyBwsi
@@HVAC_Mechanic So we have to watch another video now! Clickbait, which is just plain lies.
Would that cause the car to shut off when you put it in drive ? Or reverse ?
Bad torque converter or crankshaft position sensor?
Hello my traction light and ABs and my tire pressure light comes on no check engine light do u think it’s my wheel speed senor ?
Scan for OBDII codes, which will give a speed sensor code if one is bad. If you don't have an OBDII scan tool, automotive stores often come out and scan for free.
Good chance of it.
Does the hard shifts damage transmission?
Yes, hard shifts can cause issues and components to wear out quicker.
I changed the speed sensor, didn't stop the speedometer from jumping. changed the dash speedometer, didn't work, had wires to sensor worked on, didn't work. What else could it be?
Possible bad torque converter?
Did you figure it out I’m having the same problem
Not sure if this is relevant or not, but try disconnecting the negative post from the battery and wait a few minutes then reconnect and go for your test drive
if none of this fixes it , the only other problem could be the Wheel bearing or ECU, correct?
Take it to a mechanic and have it tested with their tool cuz the auto stores don't have the correct equipment
Hi my name is Carlos
I have a 2000 celiica GTS CHECK ENGINE LIGHT IS ON .
WON'T GO INTO 4TH GEAR .
SHOULD I BUY THE SENSOR FROM THE DELLER OR SOULD I BUY IT from auto part store?
Any advice please 🙏
Hightly apriciate. .
It's always best to get an OEM original sensor when possible.