Evinrude Etec upgrade 75HP to 90HP with Evdiag OEM factory Map, Custom EDF

We are converting a Evinrude Etec 75HP to a 90HP using a Evdiagpro.com EDF file.
1A We open Evdiag
1B we connect to our current EMM. (key Switch on to power EMM)
2 we open the exports folder on Evdiag to verify the current EDF has been automatically backed up.
2B Edf Folder is where Evdiag auto saves your edf
3 we copy that file and we send it to Evdiagpro.com with our order.(We use outlook, you can use gmail or any email you use)
4 we provide to Evdiag pro our Evdiag Auth Id to receive our release which authorizes us to program EMM's (this also can be done
with the password of the day if you have access to the BRP portal)
5 we add our release code to our Evdiag. ( we press and hold "CTRL KEY" and double click on brp logo at the same time
5B we copy the code and we send to Evdiagpro.com
Evdiag, will provide you with a Release code, we paste it and and press "ok"
Note bottom left of screen says "Dealer" Now, if code is correct, has to change to "Distributor"
Its red Because expires in less than a month.
6 we add our new 90HP edf provided by EVdiagpro.com to the exports folder to our computer.
7 open Evdiag again and go to EMM recovery ( this is to blanc current EMM, also know as cold test)
Press Next (etec I means etec Inline models)
Be sure you pick Correct EMM model ( stamped on physicals EMM)
(Im picking 586759 because is the one I have, you have to pick-up your model if is different)
Install Bootstrap and press confirm Bootstrap
Begin EMM Recovery
8 close program after cold test is load "DO NOT PRESS ON DATA TRANSFER" (otherwise you will load old EDF again)
Key Switch on
9 open EVdiag again, CONNECT and you will see ( cold test on bottom right)
10 go to utility / prepare new EMM
11 select new EDF 90HP whe says "Donor Data File" (the one mailed to you).
12 select proper Software ( on my case 3030373) yours may be different according your engine model.
13 Install Boot Strap on your engine Harness (if you don't have, you always can ground PURPLE/WHITE wire on your keyswitch (ex choke wire)
that is what bootstrap does just grounds that wire and Key Switch on
Key Switch ON
14 Confirm Bootstrap
15 Upload Engine Map
16 when finished loading map / remove bootstrap and press "OK"
17 key switch on and "reconnect to EMM"
18 Press "Data transfer to EMM"
19 Press "yes" to include Injectors
20 Connect again, and verify upgrade was sucessfull
21 Cheers you have a Etec 90HP now
You can see everithing is the same, except model (new one is 90HP), and Map (372 is 75HP, and #&# is 90HP)
Cheers Again
evdiagpro.com

[@Gibaps1]

Hello,
Can you help me?
I installed as directed. First I installed version 5.1 and then I updated to 5.9.
When I communicate, a different model number appears from my engine and then the communication is lost. It only stays connected for a few seconds.
The P/N of my emm is 587062 and the model is E30DRIIH, however what appears online is E30DPLABA 5387922. Could you tell me why this happens?

[@Ante_Restoration]

Hi is possible to tune 2002 ficht 90hp to 115 hp??

[@alannew8324]

hi wonding if you could send me the etec soft wear my disc wont load

[@mrguy343]

Can you get the files for free or do you have to pay? Where can i buy and how much? I need from 40 to 50 hp. I can't get the code anywhere

[@zasperan]

how much does it cost to go from 75 to 90 hp

[@cmau885]

I have evdiag. Same process for 40hp to 50hp? How to get dealer passwords?

[@Skits_Missions]

What is your year model?

[@cmau885]

@@Skits_Missions
2017. Also can I go to 60hp if I add water injector?

[@Skits_Missions]

@@cmau885 yes you can. I’ve changed my 40hp to a 50hp. I also have the EDF to change to 60hp. But don’t have the water valve yet.

[@Skits_Missions]

@@cmau885 but I can’t help with yours as the EDF files I have are pre 2008.

[@cmau885]

@@Skits_Missions
Thanks for the response, too bad our years are incompatible. Wondering how much power increase you noticed between 40 and 50. Also curious how you got a password to unlock distributor mode on evdiag. Please also keep me posted if you make that 60 upgrade.... Wondering how much that changes things?

[@BaZZmuZ]

Hello! How much is a edf file mod from 150hp to 175hp (or 200?)

[@EvdiagPro]

225$

[@marolamotores8698]

Boa tarde tem como estalar em português esse soltware Everud

[@EvdiagPro]

Sorry is only on French and English