The fact that it was cleaned and serviced was excellent however only if he had changed the bearings and renewed the wiring it would have surely been usable once again good job and hope to see you operationalise your projects tc
I'm starting to think these guys just take perfectly good old stuff, bash it with a hammer, and throw it in the ocean to rust for several months before digging it out to fix.
agree on the bearings, to go to this amount of trouble to refit those was a waste of time, but the windings arent burnt out, the OP mentions this in the video description
@penua You couldn't be more wrong than you are with your comment. Nowadays mechanical devices are way more efficient than old ones, just take a look at all the material improvement was done over the years. There are just 2 reasons why people come out with such ignorant opinions as yours: 1)Knowing almost nothing about the subject 2)Nowadays mechanical devices such as motors and reduces undergo way harsher conditions than before, not to say that work way more.
if it was "burnt". the winding insulation would have gone bye bye. not much of a restoration. i really wanted to see him redo those windings OR at least get a matching set and replace.
Я по работе, часто покупаем старое производственное оборудование, со старых дробилок, бетонных заводов, элеваторы и т.д. Так вот часто приходится такие засраные движки снимать, разбирать и восстанавливать, и именно восстанавливать, отдавать электрикам на перемотку статора! Шкив я бы этот снял, хотя он уже обломан, но можно наварить было и восстановить, но всё равно тут вышкой заливай, в солярке пускай отмок бы, потом бы грел его тем же резаком, чутка простукивая я бы снимал его! Подшипники сразу под замену пошли бы, у них явно выработка и от коррозии, ямки, вообщем под замену! Корпус я бы пескоструил, там не так сложно этот пескоструй собрать, а тут в ролике просто корпус почистил, кёрхером помыл и всё, типа реставрация так называемая? Я диз поставил.
Kastom Den я перематывал движки ..здесь он не показал что с обмоткой рабочие не рабочие ..есть межветковое ...ещё водой сколько брызгал ..после воды сушат в печи ...так сушить можно неделю ..на воде показывает на корпус ..так как мотор старый изоляция между пазами изношена ..надо все проверять
In this entire video , I was worried about the stator wires as they looked burnt from within. The creator have not shown that whether this machine worked or this entire mission was to make old motor look more aesthetic than before. Anyways, good amount of hard work and technical skills deserves a like and appreciation. Kudos brother.
As a somebody who has been working in the motor repair industry for nearly 15 years I can say with absolute confidence that this man has no idea what he is doing and could very likely cause massive property damage and death if he was to sell this on to some unassuming person. That motor would burst into flame within seconds of being energised. Leave it to the professionals please.
This grade-school dropout doesn't know what "restoration" even is. Reusing old bearings, not testing the windings. The way the bearings grinder when he spun the motor at the end?? garbage.
What were the insulation resistance readings between the windings and between windings and earth? Were the windings balanced? Bearings should always be replaced after exposure to heat.
DO NOT USE THIS AS AN EXAMPLE ON HOW TO REBUILD A MOTOR. This motor will not run. You cannot wash windings and not bake them dry. You should not reuse ball bearings and you could hear those bearings were shot at the end. Your bearings should not slide easily on the shaft, they should be heated up and installed. The black glue was the result of the insulation on wire heating up to the point of burning and melting. Everything about this "restoration" made me cringe. You had the money to primer and paint this but not the $3 for a f-ing eyebolt. Please tell me you threw this back in the scrap dumpster you found it in. The potential for this to kill someone is too high to even think about.
I'm sorry but if one of my mechanics/electricians did this, I would fire them. Why? Reused old bearings, sprayed the motor windings with WATER, did not megger prior to re-assembly, and failed to use proper PPE. This is an accident and FIRE waiting to happen.
Do you think he would spend all the time effort and money on a burnt out motor and your comment about the surface cleaned well he did his best and it’s not as if a pretty finish on casing is going to effect it’s working
I work on rotors and help rebuilt them. Just the mechanical side of it. Did you check the run out off the bearing surfaces to see if the shaft was running true? And the size of the key way to see if worn? If the shaft is running out too much or damage surface you can spray weld the surface and get it reground. If the key-way is bad they can be knocked in with a chisel or welded and re-machined. Blessings.
Twas fun to watch. I'm not a mechanic, but a few things came to mind. Lead paint? Will that fan eventually melt? You didn't pack the bearings at all? I would have liked to see what you reconnected the electrical feed through. The 'black glue', if by design was important. What did you find out about it? Thx for the video.
Не только. Всем понятно что это кидалово. Учи языки. Заграницей не только дураки живут) Первый комментарий переводится примерно как "Красивый зелёный якорь для лодки получился"
03:05 The wrench is in the wrong position to be torquing on that bolt. It should be either 90 deg clockwise or counte-clockwise. Then the force on the wrench would be along the axis of the shaft, not a cross it. 06:05 What??? Holding the shaft with a pipe wrench and no protection to prevent marring the shaft? 08:19 Are those OHSA approved flip-flops? 13:17 Not the way to clean motor shaft. 15:20 The wrong way to pack a bearing. Does it work?
no lo verías funcionado porque está quemado ese motor aparte le hecho agua y no lo horneo para quitar e humedad solo lo limpio y pinto pero de nada sirve si el motor está dañado
So has anyone seen this motor run? Because with my only one year experience rebuilding three phase and single phase I can tell you those windings are burnt out. But it looks pretty👍
Судя по цвету проводов обмотки мотор тупо сгоревший, а перематывать его он не стал. Поэтому и нет проверки на работоспособность - мотор заведомо дохлый.
Так железо механику ремонтируют, а электрику то сперва прозвонить нужно, это не сноповязалка и не зиповская зажигалка..... да и методы реставрации не очень щадящие, пескоструй бы многое решил, ..... только не в обмотки и не в якорь
No reviso la resistencia del motor ,mucho menos checo si no esta aterrizado el motor, los rodamientos deber ser nuevos, jamás se aisló con barniz el bobinado , tampoco reviso el ajuste de las tapas en pocas palabras hizo puras mamadas
What’s with the flip flops? Who wakes up in the morning and says “ok, well I have that big motor restoration job to do today and it’s pretty heavy with lots of metal plates and stuff so let me put on my flip flops”? Come on man, put on some shoes. No one wants to see your feet anyway.
Если бы восстанавливали как экспонат в музей - не стали бы лепить порнушный пластиковый вентилятор. Коль поставили - все ждут запуска. Но у горе реставраторов слава богу инстинкт самосохранения ещё есть, подключать ЭТО к 380в 😁
Very nice 👍🏼 To be honest I was intimidated watching at first, but now I see this is just another restoration. I don’t want to break or damage anything.
@@igorsh5936 так а где ремонт обмотки или они ток внешне красоту навели а внутрянку уже в мастерской чинить будут...видно же что он сгоревший и по обмотке и по якорю
Старые подшипники, сгоревшая обмотка, крутая реставрация 👍
I was waiting the startup of the motor!
Ha ha ha ,me too
Don't restore any thing if you will not start it up
In dream work
Yup me too!
Алле а где включённый мотор?
The fact that it was cleaned and serviced was excellent however only if he had changed the bearings and renewed the wiring it would have surely been usable once again good job and hope to see you operationalise your projects tc
He could have used electrolysis which is easier and far less trouble
Motro did't start .. Wast of time i was waiting for it
Ok....
So to summarise:
What we saw was knackered, crunchy old bearings being reused and a burned out motor...🇬🇧👍
I'm starting to think these guys just take perfectly good old stuff, bash it with a hammer, and throw it in the ocean to rust for several months before digging it out to fix.
Riayz
Note: don't expect from that motor to work... the coils are burned... the bearings are bad.
صح انا قلت هيج 😂😂ميشتغل
اتفق ✋😁
Should hv came here first 😁
agree on the bearings, to go to this amount of trouble to refit those was a waste of time, but the windings arent burnt out, the OP mentions this in the video description
Yep, the russian guys above said the same.
You turned garbage into freshly painted garbage. Good job.
Have you ever rewound 3P motor?
Паприка we would rather buy a new one with warranty and live peacefully 🙂
@penua You couldn't be more wrong than you are with your comment. Nowadays mechanical devices are way more efficient than old ones, just take a look at all the material improvement was done over the years.
There are just 2 reasons why people come out with such ignorant opinions as yours:
1)Knowing almost nothing about the subject
2)Nowadays mechanical devices such as motors and reduces undergo way harsher conditions than before, not to say that work way more.
@@DaCaRy1 What do you have to say about the documentary "The Light Bulb Conspiracy " ?
@penuaYou are absolutely right. Nowadays products are garbage.
Gap yoq vabeshe zór qoyil qoldim 👍👍👍
its like making cosmetics for dead person
Djohn Rambo the description
OK GOUD.
Китайский мотор сразу видно
Kilo ullgfrr
@@MrAli171 8
Помыл подшипники и поставил на место. Это шедевр.!
А что посадочные прошёл наждачной бумагой это нормально?😂
Lipstick on a pig. Reusing the old bearings, no testing of the windings, no wonder they didn't power it up to see what happened.
Correct rating
if it was "burnt". the winding insulation would have gone bye bye. not much of a restoration. i really wanted to see him redo those windings OR at least get a matching set and replace.
It's just restore as body 100 percent sure windinds not working
True words spoken paul bet the burnt crane was better condition than the finished motor should have been called this is how not to restore a motor
I would bet the farm that motor will NOT come close to running, big waste of time
Good video📽
Я по работе, часто покупаем старое производственное оборудование, со старых дробилок, бетонных заводов, элеваторы и т.д.
Так вот часто приходится такие засраные движки снимать, разбирать и восстанавливать, и именно восстанавливать, отдавать электрикам на перемотку статора!
Шкив я бы этот снял, хотя он уже обломан, но можно наварить было и восстановить, но всё равно тут вышкой заливай, в солярке пускай отмок бы, потом бы грел его тем же резаком, чутка простукивая я бы снимал его!
Подшипники сразу под замену пошли бы, у них явно выработка и от коррозии, ямки, вообщем под замену!
Корпус я бы пескоструил, там не так сложно этот пескоструй собрать, а тут в ролике просто корпус почистил, кёрхером помыл и всё, типа реставрация так называемая?
Я диз поставил.
Kastom Den я перематывал движки ..здесь он не показал что с обмоткой рабочие не рабочие ..есть межветковое ...ещё водой сколько брызгал ..после воды сушат в печи ...так сушить можно неделю ..на воде показывает на корпус ..так как мотор старый изоляция между пазами изношена ..надо все проверять
ASMR with high resolution photography - great 👍
Nice work mate, sad the motor is burned
I'm not even gonna dislike this video 🤣.
Need more restoration videos like this 😂
Can't believe you put the worn out old bearings back in...Far from a restoration. You just cleaned it up and painted it.
Yeah, looks pretty, but...............
I agree, but the cost might have been kinda high.
He even did not cleaned it properly.
true
I think we don't have to talk about repair cost as the main perpose of the Chanel is to teach people. I think he fail as their is alots of comments.
In this entire video , I was worried about the stator wires as they looked burnt from within. The creator have not shown that whether this machine worked or this entire mission was to make old motor look more aesthetic than before. Anyways, good amount of hard work and technical skills deserves a like and appreciation. Kudos brother.
Какой красивый кусок крашенного железа, красота!!!!!!!
Отнеси его мастеру пусть перемотает.
Доктор дью плачет
Он его даже не подключил, верно говоришь, просто крашенное железо!
As a somebody who has been working in the motor repair industry for nearly 15 years I can say with absolute confidence that this man has no idea what he is doing and could very likely cause massive property damage and death if he was to sell this on to some unassuming person.
That motor would burst into flame within seconds of being energised.
Leave it to the professionals please.
Agreed
Lets give him 95%, he/she did not replace with new bearings... Good work.
What about binding? He didn't change coil
He just Paint body
We’ll I enjoyed it. Even if it doesn’t work, who cares. The enjoyment is watching an item transformed from a wreck to almost new looking..
This grade-school dropout doesn't know what "restoration" even is. Reusing old bearings, not testing the windings.
The way the bearings grinder when he spun the motor at the end?? garbage.
. ,R45gv,
Nhìn gạch lát sân là biết kênh này của Việt Nam rồi. Ủng hộ bác. 👍👍
How do you know the motor can work without testing the coil performance? unless you are using a new or refurnish coil before work starts?
You know someone has no clue what they're doing when they pack a bearing with a butter knife
M
You deserve Restoration Academy Award!
it was so stupid because that motor was died and he doesn't repair the motor he just painted 😤
5t1
8i
What were the insulation resistance readings between the windings and between windings and earth? Were the windings balanced? Bearings should always be replaced after exposure to heat.
Chúc hai vợ chồng Lộc thật nhiều sức khỏe, và thật nhiều hạnh phúc.
DO NOT USE THIS AS AN EXAMPLE ON HOW TO REBUILD A MOTOR.
This motor will not run. You cannot wash windings and not bake them dry. You should not reuse ball bearings and you could hear those bearings were shot at the end. Your bearings should not slide easily on the shaft, they should be heated up and installed. The black glue was the result of the insulation on wire heating up to the point of burning and melting.
Everything about this "restoration" made me cringe. You had the money to primer and paint this but not the $3 for a f-ing eyebolt. Please tell me you threw this back in the scrap dumpster you found it in. The potential for this to kill someone is too high to even think about.
Yes exactly..your correct...those who do for channel not for use......❌❌❌❌❌❎❎❎❎❎
Well bro it was a very extremely impossible work . Good job
A restauração ficou ótima. Só faltou ligar, para ver se funciona.🇧🇷👍
It's a real challenge, Great job
It could be turned into the better restoration if you rewind the coils again this is like 70% job done
The time and money to recycle such scrap would not be possible without a sponsor.👽👽👽
I'm sorry but if one of my mechanics/electricians did this, I would fire them. Why? Reused old bearings, sprayed the motor windings with WATER, did not megger prior to re-assembly, and failed to use proper PPE. This is an accident and FIRE waiting to happen.
He probably did not even use a face mask good Lord how inconsiderate can an individual Be, I say get a rope
Nice Restoration
А как же пробный запуск???Или это была реставрация внешнего вида и вращения двигателя "от руки"?
Когда он без усилия надел подшипник на вал, я уже напрягся.....
@@victory_over_reason Когда он положил старые подшипники отмачиваться, я уже понял что дальше смотреть смысла нет.
Loving the Footwear .. 🫣🤭🤭
OSHA approved safety sandals.
dude, I saw it too.. he would not know how to act with boots
I almost gave him a like,even tho I wasn't really pleased by the steps of restoration,until I saw the end.
what about coils? really burned!! you have to replace it! the surface not cleaned well!! lasy work! i think ...... not working!
Try reading the description.
Do you think he would spend all the time effort and money on a burnt out motor and your comment about the surface cleaned well he did his best and it’s not as if a pretty finish on casing is going to effect it’s working
not finised yet???? why spend money ??? what for! cant use the motor!
U have to understand that this video made just to upload on youtube.
Nice paint work.
I work on rotors and help rebuilt them. Just the mechanical side of it. Did you check the run out off the bearing surfaces to see if the shaft was running true? And the size of the key way to see if worn? If the shaft is running out too much or damage surface you can spray weld the surface and get it reground. If the key-way is bad they can be knocked in with a chisel or welded and re-machined. Blessings.
Twas fun to watch. I'm not a mechanic, but a few things came to mind. Lead paint? Will that fan eventually melt? You didn't pack the bearings at all? I would have liked to see what you reconnected the electrical feed through. The 'black glue', if by design was important. What did you find out about it? Thx for the video.
Походу одни славяне угорают с такой реставрации. Двигло на свалку.
Improper way to pack bearings with grease. Windings were never checked nor the armature. Pretty green boat anchor.
Не только. Всем понятно что это кидалово. Учи языки. Заграницей не только дураки живут) Первый комментарий переводится примерно как "Красивый зелёный якорь для лодки получился"
Славяне не славяне , покажите мне хоть одного кто сказал что он ушатал посадку под подшипник, все вы здесь рукожопы.
So far, this epi is my fave. Memories of my industrial 'electrician's" helper' gig back in my olden days.
You only painted the old rusty casing. Even your painting was without removing the old one. Needs More work.
You're now God to the motor
Вспомнилась присказка - "Выкрасить и выбросить!"
Солидарен, судя по всему обмотки горевшие. Посадочное место обточил кругом
Very nice broo
03:05 The wrench is in the wrong position to be torquing on that bolt. It should be either 90 deg clockwise or counte-clockwise. Then the force on the wrench would be along the axis of the shaft, not a cross it.
06:05 What??? Holding the shaft with a pipe wrench and no protection to prevent marring the shaft?
08:19 Are those OHSA approved flip-flops?
13:17 Not the way to clean motor shaft.
15:20 The wrong way to pack a bearing.
Does it work?
Are u Mechanical engineer?
@@rahuls180 Why do you ask?
@@Tsamokie only mechanical engineer know this things in detail😯
@@rahuls180 There's our answer.
Like an archeological dig, rather than a typical rebuild.
This restoration = My ex saying I'm a changed person now!
To à
@@jamaluddin.anshari539 ..No
. .,?
The stator windings burned out in the motor. A man is engaged in hype on painting. Insane.
Después de tanto trabajo yo quería ver cómo funciona el motor
Yo lo vi muy negro al bobinadoy lo lavo y lo lavo con agua . Lo seco?
No creo que funcione ,solo va zumbar o en el peor de los casos vas a sacar humo!!
Mas que lo mojo y capas que no haya secado y no en iso embobinado nuevo para que funcionara e motor
no lo verías funcionado porque está quemado ese motor aparte le hecho agua y no lo horneo para quitar e humedad solo lo limpio y pinto pero de nada sirve si el motor está dañado
That was hell of a job!
А запустить слабо?! Реставрация подразумевает, чтобы вещь была рабочей, выполняла функции новой
Походу не работает
Woohhaaaa ...u didn't even started up the motor. Was waiting to rev up this machine
Where is the part when u perform stator winding
So has anyone seen this motor run? Because with my only one year experience rebuilding three phase and single phase I can tell you those windings are burnt out. But it looks pretty👍
However, restoration is satisfactory only for body of motor. But what about field coils ? Why field coils are not changed? Whether coils were fine ?
Maybe he doesn't understand how to install copper coils.
Việt nam vô địch🇻🇳🇻🇳🇻🇳
Почистили и покрасили железку? Где проверка на работоспособность? Что за кидалово
ТотСамый Момент А ещё керханул))
Думаю, после керхера и обжига статора в проверке нет нужды. Тот самы момент, когда "покрасить и выкинуть".)
ну практически все обезьяньи реставрации сводятся к отмывке говен и покраске желтымрозовымсеребрянкой.
Судя по цвету проводов обмотки мотор тупо сгоревший, а перематывать его он не стал. Поэтому и нет проверки на работоспособность - мотор заведомо дохлый.
Так железо механику ремонтируют, а электрику то сперва прозвонить нужно, это не сноповязалка и не зиповская зажигалка..... да и методы реставрации не очень щадящие, пескоструй бы многое решил, ..... только не в обмотки и не в якорь
Отличная реставрация!
Привет из Беларуси! 🇧🇾
Включи,б..., двигатель ,поржать хочу,мегаомметр тебе в душу...
Иван Иванов с этого начать надо а это на полку для постановки,
После Керхер смешно говорить
Да хе с ним керхер
Может я дебил но обычно работу над электромотором начинаю с "прозвонки" обмоток
павел бес Угу она так и есть! Работа начинается послн прозвонки)
Ху він запуститься там пізда обмоткам 100%
Видно по кольору її і воно була ще до то в чорному нагарі він би підключив його і там би було дохуя диму
НУ это ты как положено.а он для видео.главное покрасить.обмотки это фигня
good restration
Even too this day people still wonder does it run
МАСТЕР ЗДЕЛАЕТ 😂👍👏
Motor was in a fire so the windings are shot as you cant restore the laquer coating that keeps it from arcing
Thank for your comments
@@therestoration2r878 thanks for your generic answer
the windings did not have time to heat up
Excellent jkb done 👍
Todo bien...
Y el embobinado no se restaura??
Pues cómo va a funcionar ...
No reviso la resistencia del motor ,mucho menos checo si no esta aterrizado el motor, los rodamientos deber ser nuevos, jamás se aisló con barniz el bobinado , tampoco reviso el ajuste de las tapas en pocas palabras hizo puras mamadas
Asi es lo restauro por fuera y el bobinado no le hizo nada .aparte lo mojo y lis rodamientos igual muy mal la restauracion
Wow great work
Внутренний голос подсказывает мне, что не просто так этот кусок... покрашен был, а ради того, чтобы впарить его какому нибудь лоху, под видом нового.
я думаю человек, который покупает двигатель он не настолько тупой. Это чисто для контента было сделано
так там статору походу вата )
Very nice nice nice
you only restoration the physic.the body...you'll never restoration the electrician...and you not try to conecting with power 380 v...hahaha
he does not know how to replace bearing for motor. he uses sandpaper has number 100 to clean the shap of motor. it is wrong
@@khanhtnelectrician895
Yes correct
Very hard work 👍
What’s with the flip flops? Who wakes up in the morning and says “ok, well I have that big motor restoration job to do today and it’s pretty heavy with lots of metal plates and stuff so let me put on my flip flops”? Come on man, put on some shoes. No one wants to see your feet anyway.
Bravo maestro!
2:48 Yep, make sure you get water in everywhere. 😅
water doesn't effect induction motors as long as you dry it out, the video was underwhelming because he didn't start the motor.
Если бы восстанавливали как экспонат в музей - не стали бы лепить порнушный пластиковый вентилятор. Коль поставили - все ждут запуска. Но у горе реставраторов слава богу инстинкт самосохранения ещё есть, подключать ЭТО к 380в 😁
هل من عربي مر من هنا؟ 😂😂😂
أنا من السعوديه وعشقي التجديد
انا من العراق
@@haidarsaadwn3212 متشرفين بنت بلادي الرافدين اخوك من الجزائر 😊😊😊
انا من الهند ♥
تغضل
I love your video 😍😍😍
The coils is in good conditions?
Ahhh no... jajaja
Next time PLZZ do restoration of universal motor brother and respect to ur video great work.🔥
17:11 минут своей жизни, я "убил" за просмотром данного дерьма! Реставрация на все 100%(п****ц)
Включил двойную скорость и потратил в два раза меньше 😁
Ek puli nahi khuli kya Mistri banega re Tu😉
Обмотка сгоревшая или я ошибаюсь))) лол
Сгоревшая, даже не сомневайтесь. На роторе тоже видны следы перегрева. Не факт, что и в беличьей клетке нет обрывов.
@@__AleM__ na pewno spalony, przy podłączeniu do prądu gwarantuje pełno dymu.
Very nice 👍🏼
To be honest I was intimidated watching at first, but now I see this is just another restoration. I don’t want to break or damage anything.
Y como funciona? 🙄Era lo que todos esperamos en el vídeo... 😒 Crap!
No es posible que funcione!
El embobinado está quemado!
😯😯😯
claro eso mismo estaba esperando yo que lo pusiera a trabajar
Se supone que es una restauración completa , pero solo ver qué hasta en chanclas lo hace que se espera que funcione
I can't believe he's doing this on that nice patio
O motor esta queimando
This motor an "ZVI'' brand and USSR made.
Russia
well done bro👏
Не включил продемонстрировать работу
Александр Коваленко это наглядная демонстрация "чистого ремонта “,а не работоспособности
@@igorsh5936 так а где ремонт обмотки или они ток внешне красоту навели а внутрянку уже в мастерской чинить будут...видно же что он сгоревший и по обмотке и по якорю
Это ротор)
Игорь Поколявин смотри выше ”чистый ремонт ” чисто красиво ... осталось отвести в Электроцех на ремонт нормальный
Very good brother
No test ?
Giỏi quá, mình cứ nghĩ là sẽ thay luôn vòng bi mà lại sử dụng lại vòng bi cũ luôn. Bi cũ thì động cơ quay có ok không
-А мотор вы дяденька не унесете.
-Унесу сынок
-не унесете
-Унесу сынок
Давид и Голиафов ))
He is an expert!
This restoration is a strong proof
Like if u agree!!!