#1 failure part on yamaha superjet and waverunner pwc
ฝัง
- เผยแพร่เมื่อ 29 ส.ค. 2019
- We have had 11 failures in two months! I would say this is a common issue. This is insane. Number one failure part for any superjet or yamaha waverunner. Will show you exactly what is going wrong and how to fix it. Also how to bypass it if you really need to. This fix for a superjet that does not start also works for waverunner that does not start.
#jetskibrothers #nosparksuperjet #superjetfix - ยานยนต์และพาหนะ
![แขกคนแรกร้านแจ๊ส [ซี - เอมมี่] | iJazzKhunJang](http://i.ytimg.com/vi/XP6C9kulFfc/mqdefault.jpg)
Good info for my Waveraider. I was going to comment about using dielectric grease in the slide contact, but you covered it. The dielectric grease works well at keeping moisture out so I like to use it in my plug boots and pretty much any place where there is a chance of corrosion.
Thank You so much .I have had a problem with the jet ski cutting out for ages while I was driving and cleaning inside the switch seems to have solved the problem .
Nice, I was kinda hoping you'd do one on these. You've mentioned them before and I have a '97 Yamaha. I'll add this to the list for winter project work on the ski. Thanks!
The “Secret to long life “ of these switches is keep a lanyard connected all the time when in storage. The little rubber cover will have No pressure on it while the lanyard is connected, this stops it from splitting and leaking water 💧.
Regards Adzy
Adzy the PWC bloke in Australia! Troy great tip
The guy who sold me my Wave Venture in March 2020 told me that! Most valuable tip so far! :)
These videos are pure gold thanks.
I can no believe how much people like this video! To me it's just clips of us having a crap time dealing with little bs problems at the most annoying time.
Make a small cast of those boots then use that rubberized stuff to pour your own. Flex seal pourable rubber. Make a cast out of pourable plaster. 🤷
Thanks alot this helped me fix my ol square noise i appreciate the video!!
Thanks guys for a helpful video.
Appreciate the info.
Good video. This has plagued me last year and this year on two different skis
Awesome job ...helped me for sure.
This sounds like the issue I had last week at the ramp where I hooked up the lanyard, but it would not start. Luckily I hit the start/stop switch with some electrical contact spray I brought and it fired right up, but I think I will take apart the switch this weekend and fix it right.
Thank you, really a great video !!!
I put a 2011 VX switch on my 95' Blaster and it works. I was looking everywhere for 93-96 Blaster switches on Ebay and Amazon. Finally I realized one day that my 2014 VXS had a switch box that looked the same!
Very good video very helpful and informal. Thanks for the information wish me luck I'ma go see it this is my problem
Absolute legend mate cheers
Saludos desde Asuncion Paraguay!! Gracias thank you
Very helpful video
Fixed my switch finally. I was trying to get my ski ready for a Trump Flotilla here in CA, unfortunately I never made it. The problem was as you mentioned in your video, but a bit more of a problem. Those tiny contacts in the slide were dirty, but one was corroded and would not spring back up. I finally got it out then noticed the tiny spring inside was eaten away from the corrosion and that diameter size of spring I could not find anywhere. I had springs that 'diameter wise' were close but would not fit. The workaround "for me" was too very carefully drill out the spring pocket in the slide and cut the spring to the correct length, then pray the contact would slide up and down. "It worked". I placed everything back in the lower cover tried it out and it fired right up. Reassembled the upper cover, tried it and nothing...WTF. I tore the whole thing apart 3 times down to the contacts, thinking it must be the problem, but the problem was simpler than that. It seems when I tightened the (4) screws of the slide switch housing I over tightened it and the slide would not pop backup after having to work against the spring pressure from the lanyard button. Loosening the screws to the slide housing just a little was enough for the slide switch to work more freely. It starts every time now and hopefully will last a long time as I packed that housing with dielectric grease. The little rubber boots for the switches they sell online and if I had thought about it when I went to the electronics store I could have bought some there. Another option would be to maybe make one out of Plasti Dip.
Had no spark on my 1992 waverunner 3, cleaned the contacts and spark was re-established. Thanks for the post.
So did the engine turn over and no spark ,or did it not turn the engine over ?
@darrellsomers5427
The problem ultimately was the CDI. An after-market one was purchased, and everything ran fine. Everything is dialed in now.
For storage .. Is it better to leave the lanyard on. To help keep the spring stretched out instead of it sitting compressed for months on end? Cheers
Hey you can modify the little rubber shock absorbers on a CD player DVD player and it is identical
Great info! This was the issue with my 95 Waveventure. However, I can't figure out how to get the switch with the 4 screws out of the housing to take it apart.. I took out the 2 screws on the other side. It looks like it is zip tied way down under??
Also, if I decide just to get a new one, I don't see where the wires go down into the ski.
Thanks!
I have a 1993 Yamaha wave runner3 that won’t run in the water but will outside of it, I don’t know if this will fill/ help but thx for the info Ill try it out
It looks like the jet skis are spawning and mutating. There's a pack of mutant zombies from the 90s in your yard!
Love your videos Steve!
😂😂😂😂😂
Is there a way to bypass the switches ? I was reading that if you connected the two browns together it can bypass it completely ,, what do you think?
Great video ,question do u sell parts?
Just watched your video and it seems to be my problem- the little metal tabs in the kill switch are missing. I was going to replace the kill switch with a generic one. I tried to disconnect the black and white clip but it wouldn’t start. I checked and I have power in red wire coming from battery lead going to kill switch… any suggestions?
I have to hit the engine start button multiple times in a row to get the starter to crank. That’s the switch right?
So will the switch let the engine turn over but no spark ?
I think I’m having this issue with my Kawasaki. I replaced everything to get spark and still not getting spark. Stop switch has torn boot and all water in it. Any thoughts?
I have a 2001 Yamaha wave runner and it has no spark ! I disconnected the black and white pigtail but no spark? What do think ?
Thanks
Would it be the switch if it starts up fine but the landyard or kill switch won't cut it off?
I have no power at the White connector that plugs into the start stop box White connecter what do you think it could be?
Hi, just bought a 1997 1100, same issue, it was starting but not anymore. Is this a good unit to keep?
Hi. Great video. I want to ask you , if i can, a question. I own a Yamaha waveraider 1100 1996 and its ok but when im riding it suddenly stops. I chek batery sparks its all Good. What can I do?? Many many thanks
I feel like you could modify the switch entirely put a toggle switch for ignition and get a lanyard switch for a outbound and a push button for starter
Sometimes you can test this by pulling the spark plugs and watching for spark. No spark while the button is being held down and it will spark momentarily when the button is released.
Also, jet ski solutions out of Georgia will fix these. I had them do one for my fx1 and it has at least 6 or 7 seasons in it so far.
Guys i got a quick question long story short i have a Yamaha 1100 triple i think the cdi box is bad is it possible that it won't advance timing past idle spark or is that a stator problem anything would be great thanks again you guys are great
Have a 36 year old js650sx switch þhat only Sparks ɓy looping together start wires inside electric box. Both switches continuity check out.cleaned. please clue me in??
Thanks for that. BUT my issue is that my jetski turns over but there s no spark? Which means the lanyard switch works but there s no spark? Is it still the same issue? Because I guess if it's the switch issue it won't even turn over? Pls let me know. I m very confused here. Thanks
Anyone know which Kawasaki Jet Ski on/off switch will work with a Yamaha 760 WaveRunner?
Try this one: I take my xl700 10mi to end of the island great engine but we go to leave it cranks and start to accelerate and boom nothing no spark. I noticed the fuse popped in the ign box put another in and nothing even pulled a spark plug and held onto it I should have got shocked. Cranks over fine but won't spark anymore I'm thinking stater I don't think the start stop would pop my fuse. Wut would u guys try on this?
Please can someone help me no spack on my Yamaha waverunner gp1200r but cranking
Can you guys get a kill switch like even the whole box, mines a 650 Yamaha waverunner 1993
thank you for this great video, I just bought a 98 waverunner that will start but will not shut off, I've already swapped the on off switch and had the same results , any ideas?
You need a Diode someplace after the ON switch
I found a trade for those little rubber boots you're talkin about it was many assorted ones at the hardware store in the nuts and bolts hardware section there was some assorted stuff at the far end little knobs assorted switches excetera and they had a little tray with about five or six different kinds of those rubber switch covers boots. They were about ten bucks a piece they were not cheap but they had them in different sizes. Also may check eBay for waterproof toggle switch boot. John from Marble Falls Texas
Can you put dielectric grease on those switch terminals once you clean it off ?
I have tried it and the grease makes the switch move too slowly. You might be able to get away with an extremely light coat
Does it still turn over I’m thinking it’s my CDI
I have a Yamaha xl 700 04’ that isn’t firing regularly. It will crank sometimes but won’t others. Any idea what it might be? Start Stop switch or coil maybe?
Richard Owens I have a 2003 xlt800 same problem. I did this and still the same problem. Any luck fixing yours yet?
They got this stuff now in the store that acts and does not get hot it is liquid black scotch tape I put it on everything with wires that evolves around water and it peels off if you need to do repairs David around all of that cover all that steel and you’ll never have a problem it is pretty neat
use a 3d printer to make the rubber boots, plus some silicone sealant?
When the start stop switch goes bad, will it crank and not have spark? Or just do nothing at all?
It can do either
My switches all look good inside and out and I still have no spark
Can I unplug the black and white plug and start to diagnose on land and plug it back in to kill it?
Yes
Hello I have a start stop problem can't find a part do you have one for a 1993 yamaha waverunner??? Please
What part do you need? I may be able to help.
I have a very similar problem it turns, but I don’t have no spark
Why can’t you plug it back in then use the stop button?
Try loading it full of Dielectric grease(available at any auto parts or hardware store)
When the switch fails does it still crank??chasing a no start issue with mine. Cranks but doesn't fire
Will turn over but will not fire
@@Mobileian check for fire to coils. If it is getting fire to them but no spark then it is bad coil or kill circuit which you can disconnect. Worst case is bad igniter.
Would the engine still crank just no spark? Or no crank at all
That's what I wanted to know
So with the switch looking like that. will that not let power get to the spark plugs and it won't start
correct
Sweet man thank you so much I hope this solves my problem with my Sea-Doo
So it be your thoughts would it be just best to buy a new starter switch or just try to clean it
I've got a 1996 Yamaha waverunner 760. No spark. No power in the entire ignition system. I bypassed the off switch made no difference. Unplugged the Cdi no voltage coming from any of the coils when cranking. No voltage to ignition coil coming from cdi. All connections in ebox are good with no corrosion. Wiring harness looks good from front of engine to ebox and from handlebars to ebox. Ignition system completely dead. Only the starter works.
Any ideas?
If you have power going in but nothing coming out... bad cdi/igniter. Be sure fuse is good...
@@aNuthaRedneck Your correct that was it. 👍 I put a new CDI in several months back and it's been running good.
What fuse and where is it located
Good to know got a pair of 500 waveys for 300$ see what I can make run lol
Do you think that's the problem with a 2001 Yamaha waverunner? It cranks but won't start
Joel C plaza definitely a possibility, it’s the exact same part
Thank you so much. Someone is selling it for $1200 and said it cranks but won't turn on. Should I risk it and buy it?
Joel C plaza If I was you I would run a compression check on it and as long as it has reasonable compression on all cylinders then I would definitely chance it
Thank you so much
Joel C plaza Glad to help and good luck 👍
I hope that my trouble. Thanks
What if you convert it to a Kawasaki switch?
it can be done
I have broken alot of stuff on a yamaha and that my friend I have yet to break 14 plus years of riding. Lol
Classic 😂 but we have fixed 9 of them in one year so 🤔 might be a salt water thing 🤷🏻♂️
JetSki Brothers I might just be lucky cause im in Salt water too and dlip them often! But me and wear rings don't get along! Lol
Costas Georgiou 😂
If that's your problem and you can't shut it off all you have to do is hold the choke out it will shut down
Stop showing that waveblaster like that🥵 its popcorn time bro...teach us how to triple 1200 a wb1😜
sorry buddy I can't go out of chronological order on these videos, it would make for tons of spoilers
@@JetSkiBrothers hahaha...dammit!!
Uh oh..i see a yammi gpr
Grease it
Newer yamaha jet ski start stop dead man assy's is $360!!!
$109 on eBay
These are what is wrong with your Yamaha ski! The last Kawasaki switch swap I did was yellow to brown, white striped red to red, then black and white to black and white.
Which Kawi switch for a '97 GP760? If I open it up this winter and I just decide to replace it cuz it looks like hell... got a part number? :)
I cant believe you remember that good job👍👍
@@JetSkiBrothers haha, thank you. I did it not that long ago, and I did it just like 2 days ago to take it back off because it broke just like a yamaha switch does. The same kill switch part and everything.