Superposition Theorem Explained (with Examples)

แชร์
ฝัง
  • เผยแพร่เมื่อ 31 ก.ค. 2024
  • In this video, Superposition Theorem is explained with examples.
    So, in this video, first, Superposition Theorem is explained using one example of an electrical circuit and then three examples based on this Superposition Theorem has been solved.
    Superposition Theorem Statement:
    Any linear bilateral network containing more than one independent sources, the response in any of the branches ( Voltage or Current) is equal to the algebraic sum of the responses caused by each individual sources acting alone, where rest of the sources are replaced by their internal impedance.
    So, ideal voltage source will be replaced by a short circuit and ideal current source will be replaced by an open circuit.
    This Superposition Theorem is quite useful when circuit contains more than one independent AC sources with different frequencies.
    To apply this Superposition Theorem, the network or circuit has to be linear and bilateral.
    To, know about linear and bilateral network check my other video on Classification of Electrical Networks
    • Classification of Elec...
    This Superposition Theorem cannot be applied for the power calculations, which is the limitation of this Superposition Theorem.
    If the circuit contains any dependent source, then during the Superposition Theorem analysis, all the dependent sources are kept on. Or in another way, we can say that dependent sources are not turned off during the analysis.
    The timestamps for the different topics in the video is given below.
    2:23 Superposition Theorem Statement
    4:21 Example 1 (With Current Source)
    8:34 Example 2 (Power Calculation)
    13:31 Example 3 (With Dependent source)
    This video will be helpful to all student of science and engineering in understanding the Superposition Theorem in the electrical circuits.
    Follow me on TH-cam:
    / allaboutelectronics
    Follow me on Facebook:
    / allaboutelecronics
    Follow me on Instagram:
    / all_about.electronics
    Music Credit:
    www.bensound.com/
  • วิทยาศาสตร์และเทคโนโลยี

ความคิดเห็น • 221

  • @ALLABOUTELECTRONICS
    @ALLABOUTELECTRONICS  7 ปีที่แล้ว +38

    Minor Correction at 11:50 ; It's 2*[〖√9+√25+√49]〗^2

    • @karthiksukumaran85
      @karthiksukumaran85 6 ปีที่แล้ว +4

      ALL ABOUT ELECTRONICS why is v1=-i1 in ex 3

    • @HabiburRahman-ol2lu
      @HabiburRahman-ol2lu 5 ปีที่แล้ว +3

      Sir..i think you shouldn't give every resistor 1π or same.if you not do this-it will help us to understand correctly which one, you are using.

    • @animasgaming522
      @animasgaming522 5 ปีที่แล้ว +2

      @@utena8518 Lol 8 month later 😅😅😂 still thanks for telling because I was wondering the same but I figured it out and then came to comment section 😅

    • @subhashpurushothaman3831
      @subhashpurushothaman3831 4 ปีที่แล้ว

      Even I was about to comment the same thing sir....I like the way you explain things but pls consider this request of mine....pls give some other value other than 1 for resistors to understand the same much better.......and one more thing if am not wrong there is a mistake in your calculation sir, you can't separate things within square root with squares like that while calculating Pmax......reply me if am wrong....

    • @kgamphulanga9315
      @kgamphulanga9315 4 ปีที่แล้ว

      why did you remove R from the square root , i think this is mathematically incorrect

  • @dd-iu6iy
    @dd-iu6iy 6 ปีที่แล้ว +29

    You make this video perfect.
    I realize that it is very hard to draw figures of resistance, battery,etc.
    And show slide line by line.
    Good work bro

  • @umasrivastava4142
    @umasrivastava4142 4 ปีที่แล้ว +13

    “........And the circuit will look like this”
    Thank you sir.

  • @sharminmonika8887
    @sharminmonika8887 4 ปีที่แล้ว +6

    Though you are so fast , your tutorials are really clear, educative,and informative.Thanks a lot.

  • @nikeshparajuli6345
    @nikeshparajuli6345 5 ปีที่แล้ว +5

    Appreciate the effort.Thanks a lot .

  • @techgamer1333
    @techgamer1333 6 ปีที่แล้ว +1

    nice work I want more problem-solving circuits hopefully u will do that like this video

  • @aryantiwari986
    @aryantiwari986 3 ปีที่แล้ว +1

    very nicely explained ....you did a great job by creating this video.....bcz of which i am able to comlete my syllabus quickly ,,,,you explanation is out of remarks....finally '''''GREAT JOB''''''

  • @swapnilsingh6899
    @swapnilsingh6899 5 ปีที่แล้ว +2

    in ex3 for 1ohm resistance voltage diff. is v1 so it given or we have considered it as v1 due ti dependent source 4v1 and why v1 = -i1 it should be i1 only.

  • @cpavithra8880
    @cpavithra8880 4 ปีที่แล้ว +1

    Sir,why you can replace with one ohm resistor in the case of considering current source alone

  • @paramjitkaur181
    @paramjitkaur181 5 ปีที่แล้ว +4

    Sir had we considered that ammeter is non ideal in first case. Otherwise those two resistors will be short circuited. Also in removing voltmeter the wire was connected. But while removing 1A source u didnt removed wire which will create short circuit

  • @bruceramirez9474
    @bruceramirez9474 6 ปีที่แล้ว +1

    Excellent explanation

  • @hruturajkedar1547
    @hruturajkedar1547 6 ปีที่แล้ว +6

    Concept is cleared ,thank u☺️

  • @olaoluwaomopariola4867
    @olaoluwaomopariola4867 3 ปีที่แล้ว +1

    Great video, but I wish you would make your pointer brighter. I had to rewind like 4 times wondering which one ohm resistor you were talking about before I saw that there was actually a very small pointer moving to show what you were saying. So maybe make it bigger and a color like orange, so it's very easy to follow what you're explaining

  • @amaytiwatane6661
    @amaytiwatane6661 5 ปีที่แล้ว +9

    Put one video of Tellegen's theorem

  • @rajendrashah7921
    @rajendrashah7921 7 ปีที่แล้ว +4

    Excellent very nice theory

  • @sriranganayakulugadey202
    @sriranganayakulugadey202 5 ปีที่แล้ว

    Best explanation ever seen

  • @priyanshisomani9569
    @priyanshisomani9569 5 ปีที่แล้ว +1

    Sir, in the last example, the potential across the 1ohm resistance is v1, this is given in the question?

  • @muralimohanreddy1344
    @muralimohanreddy1344 5 ปีที่แล้ว +2

    Excellent explanation BROOOO......

  • @protikhalder8750
    @protikhalder8750 6 ปีที่แล้ว +1

    I couldn't understand how did u wrote the equation by applying KCL at v1" in the last problem in 2nd case

  • @aakashharish9373
    @aakashharish9373 3 ปีที่แล้ว +2

    Thank you so much 😊

  • @nishkarshshukla2908
    @nishkarshshukla2908 6 ปีที่แล้ว +1

    a very good lecture

  • @hehek1536
    @hehek1536 4 ปีที่แล้ว

    at 5:30 how is the short circuit same as 2 sets of 2 parallel 1ohms? A set on the left is correct but how did the set on the bottom be there? I thought those two 1ohms would disappear since the circuit is shorted.

  • @NikhilSingh-yk3gc
    @NikhilSingh-yk3gc 4 ปีที่แล้ว +2

    Video helped me 👍👍

  • @dilipgowdaan4666
    @dilipgowdaan4666 5 ปีที่แล้ว +1

    Super easy sir
    Thanks so much

  • @deepanshupandey5435
    @deepanshupandey5435 3 ปีที่แล้ว +2

    this is nothing but a good video

  • @yashwardhansingh6677
    @yashwardhansingh6677 4 ปีที่แล้ว +1

    worth watching videos. what software do you use ?

  • @rajabhay6535
    @rajabhay6535 4 ปีที่แล้ว +2

    Super way to make understand bro.. thanks a lot

    • @abhaykewate__
      @abhaykewate__ 6 หลายเดือนก่อน

      Hey we have same name

  • @moazelsawaf2000
    @moazelsawaf2000 4 ปีที่แล้ว +4

    Thanks sir

  • @nemalasurya7623
    @nemalasurya7623 6 ปีที่แล้ว +1

    your way of explination very clear..thank you so much sir

  • @shadowphotography2848
    @shadowphotography2848 3 ปีที่แล้ว +1

    Thank you!

  • @sjjayaswal7621
    @sjjayaswal7621 2 ปีที่แล้ว

    Thanks for information 👍

  • @arizaftab4840
    @arizaftab4840 3 ปีที่แล้ว +2

    Excellent 👍

  • @sathyamoorthy8763
    @sathyamoorthy8763 2 ปีที่แล้ว

    Thank you so much bro 🔥🔥

  • @satyamitguru
    @satyamitguru 6 ปีที่แล้ว +1

    Plz keep a video of reciprocity theorem

  • @lcm-nx2zi
    @lcm-nx2zi 10 หลายเดือนก่อน

    Can anyone explain In 5:20, why the two 1ohm resistor can be consider as parallel but on the other hand in 5:49 the 1ohm R why is that in series with the 0.5ohm resistor

  • @tharii314
    @tharii314 ปีที่แล้ว +2

    3:23 I just heard something... Actually a sound effect I was looking for.

  • @santoryu8940
    @santoryu8940 5 ปีที่แล้ว

    Why is I1 negative? at V' = I1? is it because of the polarity of the resistor?

  • @Mere_Human
    @Mere_Human 3 ปีที่แล้ว

    Its help me, thanks sir

  • @dolanagamukeshvabilisetty8958
    @dolanagamukeshvabilisetty8958 ปีที่แล้ว

    Super explanation

  • @drsudhabhutada3565
    @drsudhabhutada3565 3 ปีที่แล้ว

    Sir please let me know how to make such type of video. I really appreciate your videos

  • @karimfaizy766
    @karimfaizy766 5 ปีที่แล้ว +5

    bro do not avoid that people make on you critisim. this is your excellent point.

  • @animasgaming522
    @animasgaming522 5 ปีที่แล้ว +1

    This video cleared my doubts thanks sir keep uploading

  • @kesiyajoseph5222
    @kesiyajoseph5222 5 ปีที่แล้ว +1

    awsum explanation!!!👍

  • @dimitrisfotiou7280
    @dimitrisfotiou7280 5 ปีที่แล้ว +1

    thank you rly your examples make me understand the theorem

  • @storyofmaldives
    @storyofmaldives 5 ปีที่แล้ว +12

    It'll be a good idea to put subtitles

  • @MUKESHKUMAR-ir4bl
    @MUKESHKUMAR-ir4bl 5 ปีที่แล้ว +2

    thanks sir

  • @akshaynandal6409
    @akshaynandal6409 4 ปีที่แล้ว +1

    Very good

  • @tomholmez1236
    @tomholmez1236 6 ปีที่แล้ว +2

    hey, this video was uploaded on my 18th birthday!

  • @mastrammeena328
    @mastrammeena328 3 ปีที่แล้ว +1

    All other independent sources would be replaced by internal impedance
    Quire useful - AC Sources with different frequencies
    Power can't be calculated by superposition - with exam 8:45
    Min power max power
    By - Minimum and maximum current through load
    13:48 - dependent source example

  • @arinzeewuzie
    @arinzeewuzie 6 ปีที่แล้ว +2

    Concept well understood, can i make transcription of this video?

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  6 ปีที่แล้ว +1

      In English it is already available. If you want to make transcription in any other language, you are most welcome. And that will be a great help.

  • @FPerez-qc8ek
    @FPerez-qc8ek 4 ปีที่แล้ว

    When you applied the current divider rule(example 1 at 6:02) you say "into 1 ohm", shouldnt it be into 1A?

  • @harshsoni4414
    @harshsoni4414 5 ปีที่แล้ว +89

    This is " Nothing But A " Comment

  • @LionKing-yf3gw
    @LionKing-yf3gw 3 ปีที่แล้ว

    why arent dependent sources switched off ?

  • @gunnalasaidineshreddy1147
    @gunnalasaidineshreddy1147 6 ปีที่แล้ว +3

    Tq bro

  • @tayyab.hussain786
    @tayyab.hussain786 5 ปีที่แล้ว +1

    What's the meaning of this "Short Circuit" that replaced V2

  • @ut7111
    @ut7111 ปีที่แล้ว +2

    2:3 super thankyou sir

  • @suthiraheenetimulla8123
    @suthiraheenetimulla8123 5 ปีที่แล้ว

    When considering only 10V voltage source, how did the voltage across the 1Ω resistor became (-V'1)?

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  5 ปีที่แล้ว

      Because the direction of current is assumed in a clockwise direction. i.e I1 is flowing in a clockwise direction.
      So, if you apply KVL, then V1' = (-I1)*(1 ohm)

  • @arafatrahman2186
    @arafatrahman2186 6 ปีที่แล้ว

    sir ...at the last example ..v1"-2 +v2/5=0 is written...but by sign convention V1 should be negetive ....I could not understand this point

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  6 ปีที่แล้ว +1

      At supernode, the KCL is applied. See, 2A current is going into the node. While other two currents (V1''/1ohm) and V2/5 ohm are going away from the node. So, if you consider the incoming current as negative and outgoing currents as positive then you will get the above equation. If you consider the sign convention other way around (Outgoing current as negative and incoming current as positive ) then also you will get the same equation.
      I hope it will clear your doubt.

  • @lakshyasethi9727
    @lakshyasethi9727 4 ปีที่แล้ว

    in third example, why is V1'=-I1 and not +I1

  • @judy-chan4536
    @judy-chan4536 4 ปีที่แล้ว

    in the last example, how is V1' a voltage drop? the source is clearly flowing from low potential to high potential which is clearly a voltage lift. if your 1I1 is negative then your dependent voltage of 4V should be negative as well, but obviously it isn't since its experiencing a voltage lift lol.

  • @sandhyasandhya2898
    @sandhyasandhya2898 6 ปีที่แล้ว +1

    super explanation sir thanku so much it is very useful to me

  • @nishanthsinceborn
    @nishanthsinceborn 5 ปีที่แล้ว +2

    Bro.. Awesome awesome awesome..... Congrats.. It's very useful... Keeping doing😘😘😘🤗🤗🤗🤗🤗

  • @jeetenderkakkar7570
    @jeetenderkakkar7570 4 ปีที่แล้ว

    a 230V 50hz ac supply is connected to a resistance 2.5ohm coil of inductance 0.06h and capacitor of 6.8uF connected in series. calculate
    impedance of circuit
    current
    phase difference between voltage & current

  • @jayantrkulkarni67
    @jayantrkulkarni67 2 ปีที่แล้ว

    Can you add AC circuits transient analysis?

  • @uzaircheema3555
    @uzaircheema3555 5 ปีที่แล้ว

    thank u sir

  • @PlayStore-lf8wk
    @PlayStore-lf8wk 4 ปีที่แล้ว

    Nice👍🏼👍🏼

  • @reddysaimaram
    @reddysaimaram 6 ปีที่แล้ว +2

    Nice explanation

  • @kasarammoulika796
    @kasarammoulika796 6 ปีที่แล้ว +2

    excellent explanation... I'm impressed...

  • @michaelkwamedarke3741
    @michaelkwamedarke3741 3 ปีที่แล้ว +1

    I have subscribed

  • @akshayaramaswamy1954
    @akshayaramaswamy1954 6 ปีที่แล้ว +3

    Super explanation, request from me is explain about remaining theorems like Norton's and reciprocity ,

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  6 ปีที่แล้ว +1

      Norton's Theorem I have already covered at the end in the Thevenin's Theorem video.
      You may check that video.

  • @dwaipayansengupta334
    @dwaipayansengupta334 5 ปีที่แล้ว

    I perfectly understand the concept.Thank u sir

  • @gudurumadhu9391
    @gudurumadhu9391 6 ปีที่แล้ว

    good videos but u explained briefly

  • @FR0S7B1T3
    @FR0S7B1T3 4 ปีที่แล้ว

    at 15:08 how is V1 = -i1? as according to the current direction of i1, it would be a voltage rise?

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  4 ปีที่แล้ว +1

      with the direction of the current (Clockwise), there should be a drop in voltage across the 1-ohm resistor. but it is rising. That means assumed voltage drop V1' has reverse polarity and that's why with the given polarity there will be a negative sign.
      I hope it will clear your doubt.

  • @kushagraasthana532
    @kushagraasthana532 5 ปีที่แล้ว +1

    Thanks a lot sir

  • @manashrisattigeri9992
    @manashrisattigeri9992 4 ปีที่แล้ว

    In 1st problem, why you took I2 is zero, plz explain it sir

  • @huzeyfaabdella1385
    @huzeyfaabdella1385 3 ปีที่แล้ว

    at p=i2R you took common multiple of them out ok but you should have square 2 also because the square is for all the component which is radical of (square root of 25+49+9)
    the 2
    my second question is how V1=-I1
    can you answer it plz
    this question is nothing but a request

  • @farzadarafjamil411
    @farzadarafjamil411 5 ปีที่แล้ว

    Nothing but a, THIS!

  • @mayurshah9131
    @mayurshah9131 7 ปีที่แล้ว +2

    nice Narration

  • @anishchhabra5313
    @anishchhabra5313 5 ปีที่แล้ว

    U didn't explained the formula to find p max and p min..

  • @techieboy1983
    @techieboy1983 3 ปีที่แล้ว +1

    I have a doubt in 3rd ques that how you decided direction of current source when you considered 2A as current source

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  3 ปีที่แล้ว

      2A current is entering the node. while the other two currents are leaving the node.
      That's why there is a negative sing before 2A current source in the equation.
      I hope it will clear your doubt.

    • @techieboy1983
      @techieboy1983 3 ปีที่แล้ว

      @@ALLABOUTELECTRONICS thankyou 😄

  • @lakshay0132
    @lakshay0132 6 ปีที่แล้ว +11

    Nothing but a ka taaau ,,, mstt samjhaya

  • @sambenkamel
    @sambenkamel 4 ปีที่แล้ว

    At 6:21 The current that is going through the .5 ohm resistance is .25 A so the current going through 1.5 ohm resistance is going to be .75 A which is not reasonable because the larger the resistance the lower the current which is not consistent in this example because the larger resistance is 1.5 ohm and it has the lower current which is reasonable and logical.

    • @MinutesAcademy
      @MinutesAcademy 10 หลายเดือนก่อน

      yesss.....bro its 1.75

  • @saikatshee6273
    @saikatshee6273 4 ปีที่แล้ว

    What is the defference between superposition and thevinin theorem ?

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  4 ปีที่แล้ว +1

      The superposition is used for linear circuits. And to find the current or voltage across the particular element, only one source is considered at a time. The overall response (current or voltage across the element) is the summation of the individual response.
      The Thevenin's Theorem is used to find the equivalent circuit across the to terminals. Using it, any linear circuit can be replaced by the Thevenin's equivalent voltage source in series with Thevenin's equivalent resistance across the two terminals of the circuit.
      For more info, please check my video on Thevenin's Theorem.

  • @ritikajain9346
    @ritikajain9346 6 ปีที่แล้ว

    Video is gud but plzz upload more question solving videos which are covering all types of questions

  • @allipsasethi2927
    @allipsasethi2927 3 ปีที่แล้ว +1

    someone plz explain why in the 2nd ex in Pmin we took total current as (I3-I2-I1) ???

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  3 ปีที่แล้ว +1

      P min = I min^2 x R. So, to find minimum power, current should be minimum. (I3 - I2 - I1) is the minimum possible value of current. And hence, it will give minimum power.

    • @allipsasethi2927
      @allipsasethi2927 3 ปีที่แล้ว

      @@ALLABOUTELECTRONICS thankyou but .. y is i3-i2-i1 the min. Current??

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  3 ปีที่แล้ว +1

      At 11:27, I1, I2 and I3 are calculated from the given power. So, for a given R, the (I3 - I2 - I1) will make the current minimum. Isn't it ??

    • @allipsasethi2927
      @allipsasethi2927 3 ปีที่แล้ว +1

      @@ALLABOUTELECTRONICS thankyou sooooo much 🥺🥺 this was the 1st time .. my doubt cleared via utube 🙏🙏🙏

  • @janakiram8842
    @janakiram8842 4 ปีที่แล้ว

    Can we use mesh or node analysis while solving ckt in super position theorem

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  4 ปีที่แล้ว

      After applying superposition (Considering only one source at a time), the equivalent circuit can be solved using the node or mesh analysis.

    • @janakiram8842
      @janakiram8842 4 ปีที่แล้ว +1

      @@ALLABOUTELECTRONICS thankyou

  • @piyush9355
    @piyush9355 5 ปีที่แล้ว

    In last example why is it - 5I1 and not +ve as there is a rise in that 5ohm resistor.

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  5 ปีที่แล้ว

      Because if you move in the clockwise direction, then there is a drop across the 5-ohm resistor (moving from positive voltage to negative voltage). That's why it was considered negative.

  • @Rakeshkumar-bp5ku
    @Rakeshkumar-bp5ku 3 ปีที่แล้ว

    How to know which sources is dependent??

    • @umeshkumarpandey9222
      @umeshkumarpandey9222 3 ปีที่แล้ว

      Diamond shaped sources are dependent while the circular ones are independent

  • @dileepbillingi7016
    @dileepbillingi7016 6 ปีที่แล้ว

    WHAT IS LINEAR NEYWORK????

  • @leminos6119
    @leminos6119 5 ปีที่แล้ว

    How did you find the minimum power??

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  5 ปีที่แล้ว

      Pmin = Imin ^2 *R.
      Or in other words when the algebraic sum of I1, I2, and I3 is minimum. (i.e I3-I2-I1)

  • @vishnu5027
    @vishnu5027 5 ปีที่แล้ว

    How is it +V1' ? Why is it - to + at 1 ohm resistor?

  • @tushardangayach5263
    @tushardangayach5263 4 ปีที่แล้ว

    Sir last question main supernode nahi lagega, please check this again.. Total current across 5 ohm will be 4/3

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  4 ปีที่แล้ว

      If you simply apply the loop equation in the outer loop then it won't require. ( I mean no need to apply the concept of supernode) but when it is solved using the nodal analysis method then there will be a supernode.

  • @protikhalder8750
    @protikhalder8750 6 ปีที่แล้ว

    Can anyone pls tell me what is a supernode?

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  6 ปีที่แล้ว

      Please check this video on supernode for more information.
      th-cam.com/video/iIswDPKSQT4/w-d-xo.html

  • @EsmeWootliff
    @EsmeWootliff 6 หลายเดือนก่อน

    why at 7:50 is the current through the 1ohm resistor 0

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  6 หลายเดือนก่อน

      In the Wheatstone bridge circuit, since the resistance of all the arms are same, the point A and B will be at the same potential. And that’s why no current will through 1ohm resistor at the centre.

  • @psubramanyam6831
    @psubramanyam6831 ปีที่แล้ว +1

    How to take direction

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  ปีที่แล้ว

      Please watch the video on KVL for direction.
      th-cam.com/video/dlROTnDbULo/w-d-xo.html
      If you still have any doubt then let me know here.

  • @souravbarua9685
    @souravbarua9685 4 ปีที่แล้ว +1

    all good..
    please be more careful using nothing but nothing but all the time..

  • @towsifsalauddin3138
    @towsifsalauddin3138 6 ปีที่แล้ว

    as far as i know after replacing 1 volt with short circuit current won't pass through right and below 1 ohm resistor as current likes to pass through the path with less resistance the current will simply pass through the short circuit.

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  6 ปีที่แล้ว

      What you are saying would be true if there is a short circuit in parallel to the current source. (Across the current source)

  • @satishroyal7933
    @satishroyal7933 3 ปีที่แล้ว

    Sir ur videos r super but don't write on the screen sir we r unable to see the video

  • @pratikmutyalwar2613
    @pratikmutyalwar2613 5 ปีที่แล้ว +2

    Sir electronics ki puri book dalo 11class of ssc

  • @subashinit3422
    @subashinit3422 4 ปีที่แล้ว +1

    Please give me easy way to pass important questions and important topics in each units wise give me please in circuit analysis-1 second semester for engineering

    • @ALLABOUTELECTRONICS
      @ALLABOUTELECTRONICS  4 ปีที่แล้ว

      Please go through the second channel.( ALL ABOUT ELECTRONICS- QUIZ). There is an entire playlist on network analysis subject.