If you can't pop the disc off by tapping with a hammer, the small (M8 IIRC) threaded hole on the disc can break a rust seal. A quick scrub with a wire brush should reveal the threads.
Shoes and wheel cylinders on the PX2 are super easy. I just did mine. Word of caution, if you do yours, make sure you properly inspect your new wheel cylinders before putting them on. I got a Pagid set because that was all I could get ahold of here in Blighty. I found the bleeder screw was not seating correctly in one of them and it was leaking fluid out and air in. I didn't discover it until it was back from the test drive and found brake fluid spray all over the inside of the wheel. Also remember that if your drum is stuck to the hub, you can use the set screw to crack it open. I found both of mine were seized pretty good and hammering wasn't doing anything so I turned the set screw into the threaded hole on the drum and it popped right out.
Check Euro car parts - tidd.ly/3lIO7xA (use discount codes on site)
Front brake discs Ebay - ebay.us/cNLTuV
Front brake pads Ebay - ebay.us/rAHe9l
Tools used :
Milwaukee 3/8 Drive Mini Impact driver - ebay.us/Pg8ilg
Socket Set - amzn.to/2O6BUmM
Spanner set - amzn.to/2DlwUZm
1/2” Milwaukee impact driver - ebay.us/4SOewF
17/19/21 wheel bolt impact socket set - amzn.to/3gDnBlP
Torque Wrench - amzn.to/2VZ4CKu
Screwdriver set - amzn.to/30RA53L
Copper grease - ebay.us/ckQddu
Brake cleaner - ebay.us/TenE90
Ceramic brake paste Amazon - amzn.to/3jN87gW
Ceramic brake paste Ebay - ebay.us/GbuDhL
Large grips - ebay.us/XO4oRl
Brake cleaner sprayer - amzn.to/2BLF1gX
Wire brush - ebay.us/hTtdhH
Torque settings :
Caliper carriers bolts - 115 NM
Caliper sliders bolts - 52 NM
Wheel nuts - 135 NM
I love how much pride you take in your work. I can’t imagine many mechanics would clean stuff up before reassembly. 😎👌🏻🔧
Thanks 👍 comment much appreciated 👌
Excellent, very well articulated and spot on
Thank you kindly!
If you can't pop the disc off by tapping with a hammer, the small (M8 IIRC) threaded hole on the disc can break a rust seal. A quick scrub with a wire brush should reveal the threads.
Top Job, now have you done the rear shoes..
👍 will upload if I do em
I replaced the handbrake mechanism on a Fiat Ducato that someone screwed up by putting the bottom spring in wrong, what a nightmare 🙄..
Those discs looked very worn, how many sets of pads do you recon they had had over their lifetime?
Thanks for the video mate. Do you have one for the rear drum brakes?
Thanks! Not yet if I get chance I’ll do one
Shoes and wheel cylinders on the PX2 are super easy. I just did mine. Word of caution, if you do yours, make sure you properly inspect your new wheel cylinders before putting them on. I got a Pagid set because that was all I could get ahold of here in Blighty. I found the bleeder screw was not seating correctly in one of them and it was leaking fluid out and air in. I didn't discover it until it was back from the test drive and found brake fluid spray all over the inside of the wheel. Also remember that if your drum is stuck to the hub, you can use the set screw to crack it open. I found both of mine were seized pretty good and hammering wasn't doing anything so I turned the set screw into the threaded hole on the drum and it popped right out.
Decent visual description.
Pucker tips well done, no bull tuition❤
👍👍
ASTUTE DIYDaly
👍
From Nick Ayivor from London England UK 🇬🇧 ⏰️ 17:39
Thanks nick 👍
Execellent. Thank you
You are welcome!
I have the same year model, and man the condition of that car is terrible, so much rust!