Sağol kardeşim büyük çaplarda bu boylarda kolay kolay carpilmaz malzemeyi çok yormamak lazım. Küçük çaplarda ince uçlu elmas lar kullanılmasi gerekir ve puntayı çok basmamamiz gerekir buda çarpılması ya neden olur
You won't see chips shoveling in any Pakistan video. There, the shops are closed as soon as the lathes are submerged under the chips. Of course, most of the time the roof and walls of these shops have already collapsed without anyone being bothered.
Ich weiß nicht, wie sie in Pakistan funktionieren, aber wir sind in der Türkei tätig und entsorgen das Sägemehl auf diese Weise, weil die Maschinen einen großen Durchmesser haben.
Teşekürler kardeşim bu silindir hidrolik pres için üretiliyor genelde büyük silindirler Demir Çelik fabrikaları hidrolik presler limanlar bir çok alanda kullanılıyor
I ran a 750 ton and the ram was significantly larger than that my retractor rams were almost that big to run a press that big the pumps and piping are massive.seamless pipe 1 inch wall.I had a leak that shot pydraul 20 yards and knocked my helmut and saftey glasses off.
I am not talking about the weight of the material, I am talking about the power of the hydraulic cylinder. We produced it for 600 tons of hydraulic press.
You obviously haven't worked in a hydraulic shop, single point is the only good way to lift that rod after it's chromed, you can use two but you put them together otherwise they slip, so you only do that when you don't have a big enough sling.
@@mrsock3380 I have been manufacturing and repairing hydraulic cylinders for 20 years. I have worked in important companies. Are you sure you watched this video? This is a ROD piston and preliminary processing has been done. I did not do the precision process because I send it outside for grinding and chrome. I do not open the channels to protect the piston.
@@MyLatheWorld Your name wasn't on my initial comment because I was replying to the person that said it was dangerous, youtube gives you notifications as if I replied to you, but it's just that I replied to the same comment.
Зачем он кулачки измеряет, там же их по кольцами на патроне можно выставить. Микромером то что мерить,вроде как под шлифовку делать, судя по чертёжу. Станок блестит, прям завидно когда приходилось трудиться на раздолбанных в хлам, которые даже не выдавали необходимой точности. У нас в регионе не ценится работа токаря, 60 тысяч рублей в месяц платят за такую работу.
Yes, I use a micrometer because my brother is going to go to the grinding shop. Actually, in our region, lathe workers are not valued anymore. We don't have enough personnel anymore. We need to appreciate the value of craftsmen.
D After watching the Russian lathe video, nothing is the same. First rule: don't work in a long-sleeved shirt 🙄and it is truly reckless to approach the machine while it is still moving.
Hello everyone have a nice day this is the amazing video ❤
Thanks bro 👍
Very Nice Machine Works.
Thanks bro 👍
@@MyLatheWorld Most Welcome
I Also Work These Machines Sir.
@@FirozmachineryStore Welcome to my channel, my colleague. Which country are you in and what do you manufacture?
👋👋👍👍show
Thanks 👍👍
Top 🔝
What
👍👍👍
👍👍👍👍
Very good turning
Thanks bro 👍
Nice to see a young lad learning.
Exactly brother, children are our future.
Güzel iş çıkardınız👏
Teşekkürler 👍👍
Nice job 🫶👀👀👍👌
Thanks bro 👍👍🤲😎
❤❤❤❤
👍👍👍❤️
İyi iş çıkardınız 👏👏
Teşekkürler 👍👍
Kolay gelsin abi yine güzel bir video olmuş
Teşekkürler kardeşim 👍👍
👍👍👍👍👍
👍👍👍
İyi çalışmalar 👏🏻👏🏻👏🏻👏🏻🧿
Teşekkürler 👍👍
Çok güzel iş çikardınız
Teşekkürler 👍
Tudo tal qual como eu faria até ao fim.
Bom trabalho parabéns.
Thank you sir
Mester ?? Kíváncsi lennék , hogy 2000 -2500 mm -en mennyit kúpol ???? THANK YOU !!!
Yes sir, I did not understand what you said, thank you very much.
Hayirli isler ustacim uzun boyda malzemede carpilma olmuyormu?
Sağol kardeşim büyük çaplarda bu boylarda kolay kolay carpilmaz malzemeyi çok yormamak lazım.
Küçük çaplarda ince uçlu elmas lar kullanılmasi gerekir ve puntayı çok basmamamiz gerekir buda çarpılması ya neden olur
Amazing work congrats!!
Thanks bro 👍
You won't see chips shoveling in any Pakistan video.
There, the shops are closed as soon as the lathes are submerged under the chips.
Of course, most of the time the roof and walls of these shops have already collapsed without anyone being bothered.
Ich weiß nicht, wie sie in Pakistan funktionieren, aber wir sind in der Türkei tätig und entsorgen das Sägemehl auf diese Weise, weil die Maschinen einen großen Durchmesser haben.
safety eyewear?
I didn't understand what you meant.
@@MyLatheWorld I think he would like to know while the person in your video doesn't even don PPEs especially when using compressed gas.
We wear it when necessary
What is the weight of this cylinder? Please mention
This ROD weighs over 9 tons, brother
Sallery kitna milta hai..
Why do you ask? What does it matter?
Harika . Böylesine büyük parçalar nerelerde kullanılıyor ? Müthiş bir işçilik. Ellerinize sağlık. 🤌🏻👍🏻👏
Teşekürler kardeşim bu silindir hidrolik pres için üretiliyor genelde büyük silindirler Demir Çelik fabrikaları hidrolik presler limanlar bir çok alanda kullanılıyor
Bilgilendirme için teşekkürler. İyi çalışmalar. 👍🏻
@@mehmettopcu3807 teşekürler 👍
Emeğine sağlık usta kolay gelsin
Teşekkürler
I ran a 750 ton and the ram was significantly larger than that my retractor rams were almost that big to run a press that big the pumps and piping are massive.seamless pipe 1 inch wall.I had a leak that shot pydraul 20 yards and knocked my helmut and saftey glasses off.
👍👍
Good CHIP CONTROL TELL ME ON THAT LENGTH DO YOU PICK UP ANY TAPPER 😮
If I remember correctly, 2400 mm is the full length, brother.
How many horse power does a lathe that size have?
This lathe has a maximum speed of 300 rpm
Brawo
👍👍
俺も43年経験者大しなものも仕上やっている あなたたちも安全やっているね
Thank you, my colleague. It is very nice to hear this from a person who has devoted years to this profession.
Dial indecater to be used still morden tool can be esey
It makes our job much easier.
Emeğine sağlık usta
Teşekkürler
In what world is that possibly 600 tons? But 0:15 that is a very dangerous way to lift it...
I am not talking about the weight of the material, I am talking about the power of the hydraulic cylinder. We produced it for 600 tons of hydraulic press.
You obviously haven't worked in a hydraulic shop, single point is the only good way to lift that rod after it's chromed, you can use two but you put them together otherwise they slip, so you only do that when you don't have a big enough sling.
@@mrsock3380 I have been manufacturing and repairing hydraulic cylinders for 20 years. I have worked in important companies. Are you sure you watched this video? This is a ROD piston and preliminary processing has been done. I did not do the precision process because I send it outside for grinding and chrome. I do not open the channels to protect the piston.
@@MyLatheWorld Your name wasn't on my initial comment because I was replying to the person that said it was dangerous, youtube gives you notifications as if I replied to you, but it's just that I replied to the same comment.
@@mrsock3380 No problem brother👍👍
Made in Selçuklu/Konya-TÜRKİYE maşaallah.
Aynen kardeşim teşekkürler 👍
Loock for LM/G channel
👍👍
My first job..
I guess it will be the first and last time for me too.
There is maximum 1.5 tons
are you sure?🙂🙂
All the americans are like: I can't believe you guys are not wearing eye protection, ear protection, jock cups, and condoms.
We use it when necessary
非常棒的技術
You made a beautiful countertop, a Chinese-made countertop.
600 tons or kilograms
I am talking about the power that the HYDRAULIC CYLINDER will produce.
@@MyLatheWorld thanks
👍👍
Может 600 т шток для гидравлического цилиндра
We catch this from the piston diameter attached to the end of the ROD. We produced 1000 tons of power for a 1000-ton hydraulic press.
@@MyLatheWorld Может это такой перевод. Я про вес . Шток не весит 600т. Это мощность пресса .
Of course, I'm talking about the power that the HYDRAULIC CYLINDER will produce, brother 👍
Зачем он кулачки измеряет, там же их по кольцами на патроне можно выставить. Микромером то что мерить,вроде как под шлифовку делать, судя по чертёжу. Станок блестит, прям завидно когда приходилось трудиться на раздолбанных в хлам, которые даже не выдавали необходимой точности. У нас в регионе не ценится работа токаря, 60 тысяч рублей в месяц платят за такую работу.
Yes, I use a micrometer because my brother is going to go to the grinding shop. Actually, in our region, lathe workers are not valued anymore. We don't have enough personnel anymore. We need to appreciate the value of craftsmen.
@@MyLatheWorld 🤝👍👍👍
Goggles??!! We don't need no stinking goggles😅😂
👍👍
hocam 17.dkdan yazıyorum soğutma sıvısı kullanılmamasının nedeni nedir ?
Özel bir sebibi yok kardeşim malesef tezgahın su sistemi sıkıntılı soğutma sıvısı kullanılması daha iyi olur
ne gerek var her yer su oluyor. bende kullanmam.
Aynen kardeşim 😃
@@bayramcosgun8948 yaz aylarinda nasil yapiyosunuz peki hocam malzeme isiniyor isininca ölçü değişiyor buna çözüm veya öneriniz nedir
Yazı kışı yok bunun kardeşim işlenen malzeme ısınır eğer ISO tolaranslari ile çalışıyorsan malzemeyi mecbur sogutacaksin
This is not 600 tons!
I'm not talking about the weight of the material, I'm talking about the power of the hydraulic cylinder
D After watching the Russian lathe video, nothing is the same. First rule: don't work in a long-sleeved shirt 🙄and it is truly reckless to approach the machine while it is still moving.
We have to choose our clothes according to the weather conditions.
No safety nothing, working without safety glasses
I actually care about our own safety.
And he is not wearing a condom either. Thats just crazy.
you people do a lot of talking but don't do shit.........
What do you expect me to do? This is the best we can do. You can do better.
the real 600 ton 😅
click bait
I don't understand what you mean by click bait. There is no trickery in my videos. You'll understand if you watch them.
👍👍👍
👍👍👍
👏🏻👍🏻
👍👍👍
👏👏👏👏👏👏
👍👍👍
Emeğine sağlık usta
Teşekkürler
👏👏👏👏
👍👍👍👍