In this video I will turn a "simple " segmented bowl using my wedgie sled. It's a good project to do for your first segmented piece. Give it a try and ask any questions you may have. Thank you.
That's a lovely bowl! My first and only attempt at segmenting was a failure - full of gaps. I'm inspired to have another go after watching this. Thanks for sharing.
Very cool, I really like it. I have been turning bowls for a while, but I am just now getting ready to start turning segmented bowls and learning about it before I start. Is there a reason you used a 4 segment bottom rather than a 6 segment bottom like the rest of the bowl? Thanks
I really like the combination of Zebra wood and walnut. The Zebra wood really sets it it apart. I want to make one and have a couple questions. What is the diameter and height of the bowl? Making the bottom ring as you did will that prevent splitting and what is the base thickness. Thanks and keep the chips coming. Glen
The bowl ended up to be around seven inches diameter and about three inches tall. Making the bottom ring out of the four pieces does make it stronger and should keep it from splitting and the base was made out of 4\4 stock that is usually more than 3\4 to just under an inch. I know I just turned it to flat. Sorry I did'nt get back to you sooner thank you for watching!
Very nice! I'm planning to attempt a segmented bowl and need to make or buy a wedge sled. Did you make or purchase your wedge template? Did you make or purchase your wedge sled? Also, the angled piece that directs your cutoffs away from the blade, how did you achieve that? Is it affixed to your throat plate? Thank you!
Go to Segeasy.com. They have free plans for building a wedgie sled and they explain the angled piece in some of their videos. They also sell wedgies for setting up proper angles for cutting segments.
Thanks for the video. You did a great job and I want to try one. A glue-up tip if you don't mind. To keep things from moving around or you might say slipping around, you can sprinkle some table salt on the glue. You don't want to put a lot of salt on it. I have been doing this for years with no problems.
Thanks Dee. The bottom is just four squares glued up, the middle ring is 6 segments cut at a 30 degree angle. The board was about 2.3 inches wide, the segment is about 4.6 inches at the widest. The middle ring has straight cut pieces between each segment that are about .25 thick. The top ring is also 6 segments, with a 2.5 inch wide board. the long edge of the segment is about 5.75 long.
Beautiful!!
It may be simple but it is an awesome looking bowl, thanks for sharing
Beautiful bowl!!!
That's a lovely bowl! My first and only attempt at segmenting was a failure - full of gaps. I'm inspired to have another go after watching this. Thanks for sharing.
Thank you! Im glad it was able to inspire you to try again!
Beautiful piece
simple but beatiful. congratulations and tks for share
Beautiful work!
Thank you!
Thanks for sharing. I thought you looked familiar when I saw your video, small world!
I'm impressed!!
Noel Perry thank you!
Beauty. We do have different definitions of simple. However you've "turned" me into a new subscriber.
Thanks Wakely! Glad you liked it.
Very cool, I really like it. I have been turning bowls for a while, but I am just now getting ready to start turning segmented bowls and learning about it before I start. Is there a reason you used a 4 segment bottom rather than a 6 segment bottom like the rest of the bowl? Thanks
Very beautiful thanks for sharing.
Thank you Tony!
Do you have a link to the app by chance Please ??
i could,nt hear what degree you set guides. for the 6 pcs
what angle is your miter sled cut at?
Very nice! Question - I noticed you put some wipe-on poly first, then sanding sealer. Isn't the sanding sealer supposed to go first?
Thank you! I did use sanding sealer first then wipe on polly. Sorry if it looked the other way around in the video.
I really like the combination of Zebra wood and walnut. The Zebra wood really sets it it apart.
I want to make one and have a couple questions. What is the diameter and height of the bowl?
Making the bottom ring as you did will that prevent splitting and what is the base thickness.
Thanks and keep the chips coming.
Glen
The bowl ended up to be around seven inches diameter and about three inches tall. Making the bottom ring out of the four pieces does make it stronger and should keep it from splitting and the base was made out of 4\4 stock that is usually more than 3\4 to just under an inch. I know I just turned it to flat. Sorry I did'nt get back to you sooner thank you for watching!
What type of wood did you use
Very nice! I'm planning to attempt a segmented bowl and need to make or buy a wedge sled. Did you make or purchase your wedge template? Did you make or purchase your wedge sled? Also, the angled piece that directs your cutoffs away from the blade, how did you achieve that? Is it affixed to your throat plate? Thank you!
Go to Segeasy.com. They have free plans for building a wedgie sled and they explain the angled piece in some of their videos. They also sell wedgies for setting up proper angles for cutting segments.
Thanks for the cell phone info. on what angles to use! Is there a cell phone location on cutting staves?
Nice I like the look of it and not a lot of complicated cuts 👍
Thanks for the video. You did a great job and I want to try one. A glue-up tip if you don't mind. To keep things from moving around or you might say slipping around, you can sprinkle some table salt on the glue. You don't want to put a lot of salt on it. I have been doing this for years with no problems.
Use
Very nice job, I particularly like the proportionality of your rings. Could you share the dimensions of the rings and segments you used. Thanks.
Thanks Dee. The bottom is just four squares glued up, the middle ring is 6 segments cut at a 30 degree angle. The board was about 2.3 inches wide, the segment is about 4.6 inches at the widest. The middle ring has straight cut pieces between each segment that are about .25 thick. The top ring is also 6 segments, with a 2.5 inch wide board. the long edge of the segment is about 5.75 long.
Nice job the six segments is nice for newbe turners to get them turning segments
Hello , what's the name of the app ? Thanks
it is the ringmaker app available on the website www.turnedwood.com. Thanks
What is the name of the app I cannot find it thank you
Sorry for the late response, it is the segmented ring maker app at turnedwood.com
What’s the name of the app you mentioned?
Its the segmented ring maker app at turnedwood.com
No Koo
You're a very good weather video
Do correctly see in your video that you are a Redwings fan?
Yes Dee I am a RedWings fan!