Hi, you're watching Tom Did It. Here I'll be showing you how I adjust the clutch on my Aprilia RS 125 2 stroke, 2010 model. Clutch tool link: www.pjme.co.uk... Thanks again for watching Tom Did It.
My apologies Tom for assuming you were from my ends I found that such coin's fit better than a washer and if you have already chewed the inside up no point using a coin thanks for a reply
On Sunday , I'll be uploading a video on my channel ( this PatRiot channel isn't mine, it's on a iPad that 6+ people have access to) It's the only hydraulic clutch upgrade I've seen like this, the Ducati ones that stick out the side of the clutch cover isn't a good idea if you dropped the bike, it's going to brake off, but what I've used is small and tucked between the barrel and oil pump. It cost £8 for the pump & £28 for the clutch master cylinder & front brake master cylinder, I have the back brake hose as my clutch, but it's too long ( 8-10 inches) and I will have to mock one up and then have it made so it fits on the bike properly like how the cable fits I've been using it since September 2020 1700+ miles and I can say it's faultless and it slightly easier to use than cable and a lot smoother, after a few days without using the bike it goes a little soft & spongey, but it only takes a couple of pulls and it is back to normal, it amazing I'll post a link from my channel to this channel Comment section on Sunday 😉👍🏽👍🏽
@@tomdidit4216 I went to get bike ready and I broke the petcock 😳 So I’m buying a new one & I’ll get a auxiliary fuel tank in the meantime, I’ll upload my hydraulic clutch video as soon as I can 👍🏼
Hey Tom, my ‘08 RS125 has a problem with the clutch where if i put it in gear with the clutch pulled all the way in, it will stall. So to put it in gear i have to get the revs up, if not it will stall. Is this something that can be caused by a badly adjusted clutch? btw i love your rs videos;)
Hi Tom, so I’ve been playing about with the Rs I bought, I found that the powervalve was stuck solid and the solenoid was solid, so after cleaning and freeing everything up I could tell straight away that the bike was running better, now I’ve noticed the bike seems to struggle going past 10,000 rpm I believe I’m running a 34mm carb but the bike seems too rich still smokes quite a bit should I modify the air intake to help with the richness? I noticed you have taken out your snorkel on the air box should I try this? Thanks
Hi Ronnie & Hilda. I’d be cleaning the carb components, checking the jet sizes then plug chop. I think and 155 or 160 is the standard main jet size in the 34mm carb? I have removed the snorkel for a bit of extra air flow, and allot more induction noise😀. Well done on freeing up the power valve. Good luck with the tuning. Tom.
Hello again. Thanks for your continued support. Honestly I’m not really qualified to advise on this. The manual states that 75-90 should be used. It’s my best recommendation that you stick to the manual (just to be on the safe side)👍 Thanks again. Tom
If you have the pbhb28 could be vaccum from the bottom of fuel tap/filter or possibly your kill switch is cutting the bike out when going in gear, good luck
My apologies for the late response. So, when in neutral the bike revs freely - You put it in gear it dies. My bike cuts off immediately when I put it in gear and accidentally leave the kick stand is down. It sounds to me like your kick stand switch could be faulty?
What’s the top speed? I love ur bike man , any performance upgrades? Ohlins suspension rare mono block ? Front suspension cartridge to adjust rebound and compression? Ecu!
Hi Chaitanya The top speed is about 150kmh as I have it geared for acceleration. I have completed some performance upgrades. Bigger carburettor, wossner piston and increased compression. No suspension upgrades at this stage. ECU is standard. It goes pretty well for a 125 and it is also light weight👍
Hi Tom
Thank you so much for your videos they are very informative.
Regards
Wayne
Simplest engine n bike to work on great for a beginner them I had them when I was 17
Hi James
Good to hear you had one. They are fun little machines!
this is what im loooking for and bang !
tommorow my clutch will be finally adjusted after new clutch cable clutch discs and springs
thanks
Greetings Gutkowski.
Glad the video is of some use!
Cheers Tom
Great video very clear thanks for your efforts
You are very welcome
thanks mate ur keep making quality videos at the right time when im getting stuck with my rebuild keep up the good content
Good to hear mate…. And good luck with the build!👌
very instructive. thanks
Great video as always!
Keep up the great work Tom :)
Phillip, thanks for your support on the channel and kind words!
Cheers pal
Another great video Tom!! You are a natural!!!
Cheers mate
Another great video Tom 👍
Many thanks David!
I bought the right cable but it's too long... even if i thighten that screw in the clutch to the max, it's still 2-3 cm too long. What do i do?
Hiya mate thanks for a tidy video I'm a big of that rotax 122 moter use a 2 pence piece next time you change your oil instead of a screwdriver 😉
Hi Darren.
Thanks for the tip.
I’ll be sure to use a suitably shaped coin next time… possibly a 10 cent👍
Cheers
Tom
My apologies Tom for assuming you were from my ends I found that such coin's fit better than a washer and if you have already chewed the inside up no point using a coin thanks for a reply
Great video pal!
Many thanks. Glad you like it! Hope it was of some use…
On Sunday , I'll be uploading a video on my channel ( this PatRiot channel isn't mine, it's on a iPad that 6+ people have access to)
It's the only hydraulic clutch upgrade I've seen like this, the Ducati ones that stick out the side of the clutch cover isn't a good idea if you dropped the bike, it's going to brake off, but what I've used is small and tucked between the barrel and oil pump.
It cost £8 for the pump & £28 for the clutch master cylinder & front brake master cylinder, I have the back brake hose as my clutch, but it's too long ( 8-10 inches) and I will have to mock one up and then have it made so it fits on the bike properly like how the cable fits
I've been using it since September 2020 1700+ miles and I can say it's faultless and it slightly easier to use than cable and a lot smoother, after a few days without using the bike it goes a little soft & spongey, but it only takes a couple of pulls and it is back to normal, it amazing
I'll post a link from my channel to this channel
Comment section on Sunday 😉👍🏽👍🏽
Go for it Pat.
Can wait to see!👍
@@tomdidit4216
I went to get bike ready and I broke the petcock 😳
So I’m buying a new one & I’ll get a auxiliary fuel tank in the meantime, I’ll upload my hydraulic clutch video as soon as I can 👍🏼
All is well mate👍
Hey Tom, my ‘08 RS125 has a problem with the clutch where if i put it in gear with the clutch pulled all the way in, it will stall. So to put it in gear i have to get the revs up, if not it will stall. Is this something that can be caused by a badly adjusted clutch?
btw i love your rs videos;)
Hi I’m got a problem my Aprilla 125 RS won’t select any gears it has become totally stiff? Any suggestions?
Thanks 🙏🏻
Bravo
Tks u Tom !
Please I have problem of fixing my clutch in Nigeria the robber inside the gear box keep melting
What oil you recommend to put in gearbox
Hi do you need to keep the cable pulled as your ajusting with the Allen key thanks
Hi Barry. Thanks for leaving a comment.
Don’t pull the cable when adjusting.
Hi Tom, so I’ve been playing about with the Rs I bought, I found that the powervalve was stuck solid and the solenoid was solid, so after cleaning and freeing everything up I could tell straight away that the bike was running better, now I’ve noticed the bike seems to struggle going past 10,000 rpm I believe I’m running a 34mm carb but the bike seems too rich still smokes quite a bit should I modify the air intake to help with the richness? I noticed you have taken out your snorkel on the air box should I try this? Thanks
Hi Ronnie & Hilda.
I’d be cleaning the carb components, checking the jet sizes then plug chop.
I think and 155 or 160 is the standard main jet size in the 34mm carb?
I have removed the snorkel for a bit of extra air flow, and allot more induction noise😀.
Well done on freeing up the power valve.
Good luck with the tuning.
Tom.
Hello what do you think about 75w80 oil for gearbox?
Hello again. Thanks for your continued support.
Honestly I’m not really qualified to advise on this. The manual states that 75-90 should be used. It’s my best recommendation that you stick to the manual (just to be on the safe side)👍
Thanks again.
Tom
@@tomdidit4216 no problem mate thanks for the answer.
Hey mate,
What manual are you using? Where did you get it?
Thanks and love the content! 👍
Hi there. Thanks for your comment.
I’m using an Aprilia work shop manual. Email me direct from my channel email
@@tomdidit4216 Hi mate, I can’t seem to find your email?
are we going to ignore the fact, that there's 600cc carved into the panel?
That's the quantity of oil
My aprilia starts and revs but when in gear and i try to move it dies
Fuel delivery problem?
If you have the pbhb28 could be vaccum from the bottom of fuel tap/filter or possibly your kill switch is cutting the bike out when going in gear, good luck
My apologies for the late response.
So, when in neutral the bike revs freely - You put it in gear it dies.
My bike cuts off immediately when I put it in gear and accidentally leave the kick stand is down.
It sounds to me like your kick stand switch could be faulty?
Hi Tom, This is my go to channel for the Aprilia. love the carb tuning video to: th-cam.com/video/3IzsN-HL6XQ/w-d-xo.html
Hello again Jaap. As usual, thanks for your comment and continued support.
I’m glad you like the video content on this one mate👍
What’s the top speed? I love ur bike man , any performance upgrades? Ohlins suspension rare mono block ? Front suspension cartridge to adjust rebound and compression? Ecu!
Hi Chaitanya
The top speed is about 150kmh as I have it geared for acceleration.
I have completed some performance upgrades. Bigger carburettor, wossner piston and increased compression. No suspension upgrades at this stage.
ECU is standard.
It goes pretty well for a 125 and it is also light weight👍
@@tomdidit4216 brake upgrades ?
Hey there
No brake upgrades - just sintered pads on front and rear👍
These bike have good brakes in stock form👍👍