Man, I thank God for your video. I am not as good in english but this video has a very nice and simple speach that I got everything without needing translation. And you helped so much thant I already know what to do as the sun raises up. Thank you
My car is Audi Q5 2012.. there is check engine sign OBDII read codes P0506 & P12A4. and when turn on there shaking and increased fuel consumption is it possible cause?
This is because I owe a Mitsubishi Pajero IO, 1.8 but with difficult first start or after a while with the engine off (at least 3h). In addition it is heavilly consuming fuel, I am talking about a full tank for only 380km....it is super abnormal.
Thank you for the video! I have 2016 kia Rio throwing codes for misfire in cylinder 1 and 3 also a code for fuel rail pressure sensor one low and one high. it’s starting rough and hesitating. Changed the sensor but didn’t fix it, any help would be appreciated!
@@moath939it means the sensor or the wiring connector is bad on the fuel rail pressure sensor it’s different from the map sensor especially if it say’s open circuit but typically when it says high voltage the sensor has malfunctioned if it says voltage low that means the wire fuse or connector is loose or wire is bad
Hi ! My car is chrysler 300 2012 model 3.0 CRD, i have code with P0088. Fuel rail system/ pressure too high. And i have changed the fuel pump and injectors all is good and i have changed 2 of fuel pressure regulator, and there is only one fuel pressure sensor left that i haven’t changed, but i have no idea if it’s the problem! Because car runs well , it doesn’t turn off, but when I drive in highway and try to pass the cars, when the RPM is high enough, and sometimes the engine lights comes out with Red lightning bolt, and i will lose the power, but still can drive with safety mode kinda! 😅 And after on, of the car few times all the lights will be gone, and everything is normal.
Hypothetically what would happen if someone just unplugged the electrical connection and unscrewed the fuel pressure sensor without doing any preparation
Man, I thank God for your video.
I am not as good in english but this video has a very nice and simple speach that I got everything without needing translation.
And you helped so much thant I already know what to do as the sun raises up.
Thank you
My car is Audi Q5 2012.. there is check engine sign OBDII read codes P0506 & P12A4. and when turn on there shaking and increased fuel consumption
is it possible cause?
This is because I owe a Mitsubishi Pajero IO, 1.8 but with difficult first start or after a while with the engine off (at least 3h).
In addition it is heavilly consuming fuel, I am talking about a full tank for only 380km....it is super abnormal.
Hi thank , i have 2012 hyundai santafe diesel and the rpm is not going over 3000 and no power , we changed diesel filter and cleaned MAS sensor
Ok. Try scan the car
Thank you for the video! I have 2016 kia Rio throwing codes for misfire in cylinder 1 and 3 also a code for fuel rail pressure sensor one low and one high. it’s starting rough and hesitating. Changed the sensor but didn’t fix it, any help would be appreciated!
Ignition coils in the coresponding misfire cylinders are bad
@@DIYAssistant I changed the coils and spark plugs too! The codes says p0193 fuel rail pressure sensor A circuit high what does that mean. Thank you!
@@moath939it means the sensor or the wiring connector is bad on the fuel rail pressure sensor it’s different from the map sensor especially if it say’s open circuit but typically when it says high voltage the sensor has malfunctioned if it says voltage low that means the wire fuse or connector is loose or wire is bad
Check the fuses and wires first that lead to the specific sensor in question for a bad broken or burnt wire on the harness or fuse
my engine starts after about 5-7 seconds. i lose power and get no fuel to the driver side banks 1, 2, and 3. Any ideas if its sensor or pump?
Whats the car make and model?
My car Vw Tiguan 2.0 tdi 140 2008 misfires when it is cold, could it be because of this?
I don't think your car is equipped with this system. Scan & check for error code
i have Audi A4 2012 model it keep saying fuel rail presser too low please help tdi 2.0
This can be bad fuel pump or bad fuel pressure sensor
Hi ! My car is chrysler 300 2012 model 3.0 CRD, i have code with P0088. Fuel rail system/ pressure too high. And i have changed the fuel pump and injectors all is good and i have changed 2 of fuel pressure regulator, and there is only one fuel pressure sensor left that i haven’t changed, but i have no idea if it’s the problem!
Because car runs well , it doesn’t turn off, but when I drive in highway and try to pass the cars, when the RPM is high enough, and sometimes the engine lights comes out with Red lightning bolt, and i will lose the power, but still can drive with safety mode kinda! 😅
And after on, of the car few times all the lights will be gone, and everything is normal.
Is there anything other things has to be changed or should just change the fuel pressure sensor ?
Yes
Hypothetically what would happen if someone just unplugged the electrical connection and unscrewed the fuel pressure sensor without doing any preparation
Error code, car may shutdown
My car accelerates after a delay when gas pedal is pressed. Is this because of this issue.??
👉th-cam.com/video/gz1PK5Kiz4I/w-d-xo.html
👉th-cam.com/video/sGjL1b12xK0/w-d-xo.html
@@DIYAssistant thanks♥️♥️