Hey that’s dielectric grease you should put a thin layer of that back in the motor contacts. That’s not what kept it from working. It was the build up of dust or debris collecting on the contacts. Dielectric grease will keep it from corrosion in the future. Also if your watching this video look at the recalibration video to complete the job.
since there are 3 of these in my sierra I'm not sure which one to change-I have air flow to the 4 vents in the dash but no defrost, no air to feet. There is only hot air to passenger side, only cold air on drivers side and only from the vents in the dash.
hay otro actuador para cambiar la direccion del aire?. Aquel que envia el aire a los pies o a la cabeza o al parabrisas o combinado?. Mi privlema es que solo da el aire hacia los pies y al tablero. Si enfria si hay aire caliente si hay fuerza y temperatura pero no hay cambio de direccion. Gracias
I ordered brand new actuator plugged it in where old was was started the car turned rear ac on and when i pressed mode change i watched actuator move and kept moving and than it started clicking and it wouldnt stop i changed mode again and it still wouldnt stop clicking what do you think could be the cause that i kept moving even though i changed mode only once i think thats the reason my old one went bad
Hey that’s dielectric grease you should put a thin layer of that back in the motor contacts. That’s not what kept it from working. It was the build up of dust or debris collecting on the contacts. Dielectric grease will keep it from corrosion in the future. Also if your watching this video look at the recalibration video to complete the job.
Njj8jjkkjjjjnkjjj845
This should be higher.
Got it working it had a ball of grease! Thanks
Great video but loose the music it's loud and goes over your voice.
since there are 3 of these in my sierra I'm not sure which one to change-I have air flow to the 4 vents in the dash but no defrost, no air to feet. There is only hot air to passenger side, only cold air on drivers side and only from the vents in the dash.
You’re likely looking at the blend door actuator for the floor vents.
Thank you Sr. Gracias Señor 👍👍👍👍😀😀😀
You’re most welcome 👍
Again, Great, concise vid, thanks
Thanks Jackson👍
Thank you, it really helps ❤️
Thanks so much Susana😊👍
I thought that cleaning it was not a good idea. But, you were right. Thank you. Cleaned out that grease and it started working again.
Excellent 👍😊
Good job. Well done
Thanks Butch😊
Just did it and back working thanks 👍
Is it jus on passenger side or drive side too what on the driver side by the pedal acceleration
Should work the same👍
great and easy fix,going to take mine out right away??Thanks, JPG...
Thank you
What year of truck are you working on? I don’t see it in the desscription
It’s a 2004 GMC Yukon.
Will this work on a 09 GMC Yukon XL ?
Should be the same👍
Great video. Gonna try repair!
hay otro actuador para cambiar la direccion del aire?. Aquel que envia el aire a los pies o a la cabeza o al parabrisas o combinado?. Mi privlema es que solo da el aire hacia los pies y al tablero. Si enfria si hay aire caliente si hay fuerza y temperatura pero no hay cambio de direccion. Gracias
Thanks Gus,
Can you send the question again in English?
Thank you😊
I'm going to try this
What year is this one?
2004👍
Good video 👍
So is this considered for the front blowing vents?
Presto 🎶✨✨✨🌟
GooD VIDEO
This is if my ac dont blow...or what is it for
It’s when your heater or ac is stuck and it won’t shift to hot or cold, it’s stuck on one.
Mines doesn't blow at all...could this be it...thanks for the info my guy
No, in your case it sounds like you may have a blown fuse or maybe a bad fan / blower motor.
if you fan is not coming on its your blower motor or blower motor resistor easy fix
Good video did it just like you and it works great. Thanks!
Like video
I ordered brand new actuator plugged it in where old was was started the car turned rear ac on and when i pressed mode change i watched actuator move and kept moving and than it started clicking and it wouldnt stop i changed mode again and it still wouldnt stop clicking what do you think could be the cause that i kept moving even though i changed mode only once i think thats the reason my old one went bad
you have to calibrate it.
@@RobertThorne-qj9qd i did that i watched it move back and forth and after that when i went to move the settings it didnt respond