How to Replace Ignition Lock Cylinder 1988-1999 Chevy C/K1500
ฝัง
- เผยแพร่เมื่อ 7 ก.ย. 2021
- Buy Now!
New Ignition Lock Cylinder from 1AAuto.com 1aau.to/ia/1AIMX00039
This video shows you how to repair, install, fix, change or replace a broken, damaged, worn or faulty ignition lock key cylinder in your 1988-2000 Chevy C/K1500.
• Check here for more videos on the 1988-2002 Chevy K1500 • Chevy K1500 Pickup 198...
This process should be similar on the following vehicles:
1988 Chevrolet K1500 Truck
1989 Chevrolet K1500 Truck
1990 Chevrolet K1500 Truck
1991 Chevrolet K1500 Truck
1992 Chevrolet K1500 Truck
1993 Chevrolet K1500 Truck
1994 Chevrolet K1500 Truck
1995 Chevrolet K1500 Truck
1996 Chevrolet K1500 Truck
1997 Chevrolet K1500 Truck
1998 Chevrolet K1500 Truck
1999 Chevrolet K1500 Truck
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oapd/1AXAA00013
• Phillips Head Screwdriver 1aau.to/oapd/1AXAA00013
• Pocket Screwdriver
• 10mm Wrench 1aau.to/oxT/1AXAA00010
• 21mm Socket 1aau.to/oHj/1AXAA00043
• Steering wheel puller
• T15 Torx Driver 1aau.to/osn/1AXAA00008
• Ratchet 1aau.to/oaw4/1AXAA00016
• 1/2 Inch Wrench 1aau.to/odQ/1AXAA00011
• Pick 1aau.to/os5/1AXAA00037
Subscribe: / @trq
Check out our playlist:
Chevy K1500 Pickup 1988-2002: • Chevy K1500 Pickup 198...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - ยานยนต์และพาหนะ
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
Whats the name of that special tool?
@@thomasvictory815 lock plate removal tool
@@thomasvictory815 l
This Young Man Understood The Walk-Someone-Through-Something Assignment.
GREAT Job, young man.
This guy is good. I used his video and swapped out my ignition switch. His personality is dry but he's still the best one I've seen.
Need to let this guy do all the how to videos
The tool he used is called a lock plate removal
Thank you!
Thanks!
Thanks!!
Thanks ese
Is it a must? Can I change the ignition without it?
Thanks for the how to. Saved me 120$.
Awesome video.... Very instructive.... VERY thorough on EACH step. This had for to be the best... How to video ...I've seen so far.. Great job ..... But I did notice if someone has a ? No one responds.... Why would they.. lol... The video covers it....
We really appreciate your great job.
Hussein's from Germany 🙋♂️
What a great video. I was in the middle of this project and got stumped. This solved my problem and I finished the job. Well filmed and easy to understand. Thank you.
+Jim H Thanks for watching our video! 1aau.to/m/Shop-TRQ
Y’all made this cake work. Really appreciate the video.
I changed my ignition in 5 minutes by drilling a small hole through the steering shroud above the lock cylinder and stuck a pick through the hole to press down on the cylinder release. quick and easy.
What size bit do I need?
@@wildestcowboy2668 Big enough to get a pick through it? lol
What about that t15 bolt holding the cylinder from falling out? What does drilling a hole from top do? I know there is a release pin but not sure if you can make a video of how I would do it? Thanks!
If that's real it is genius
Can you post a video or picture of it?
GREAT VIDEO ! And I learned a new word !! " PETON '
Thank you for this video. Very helpful and spot on!
Wow man great job on such a detailed video
Thank you ! After two days of frustration, I saw your video - so easy !!!
Very good instructional video! Step by step very accurate! Thank You!!
Thanks man I needed this
Very good video and commentary. Thanks.
You are good ! Terrific video, thanks for the schooling.
This is the best video on the internet
Awesome video. Thanks!
Great video, this helped a lot
Thank you for video you saved me 100$
Great video! Probably saved me $200.
Lost the keys to my 93 OBS and used this video. Highly recommend
+@metaworlddomination4923 Thanks for watching our video! 1aau.to/m/Shop-TRQ
Is this the way to change the ignition switch in a 1989 chevrolet blazer also?
Great video
What is that special tool called you used to press in to get that lock ring off after you pulled the steering wheel???
Thank you.
What is the 1st plastic piston u press into tumbler. Truck won't start after replacement of tumbler
You just made more work for your self by taking the wires off that's not necessary at all you don't even have to take your battery terminal off just more work
In this video, he seems to have skipped a bunch of steps taking things apart, that he is shown reassembling. Also, a "new" wiring harness? He didn't show any of that being removed & replaced in this video...
Where did the wires come from?
Whay size are the bolts to use on the steering wheel puller?
Will this work if the ignition is stuck in the on position?
You mention it must be off?
Yeah bruv, when did you remove the covering for the wiring harness around the steering column?
Where can i get another one of those screws that hold the lock cylinder in place
what is that part at 6:34 that every video i've watched refers to it as a little thingy etc. what does it do and on many older vehicles it is very brittle and breaks when removing, can you buy a replacement and is it critical.
My spring clip popped out of key switch can’t figure how it clips and stays in can you help
So, what was that “ special tool” that was used at 2:31
Substitutes in Spanish, please. Your videos are very good. I have a 1999 Chevrolet S 10 and I would like to know more about repairs to this truck. Thank you very much for uploading these videos.👍
Learn to pick with lock picks and you can decode and cut a fresh key and be done.
I normally if I have to go this deep in will pull the door, get most of the cuts then progression the remaining amount.
yes. But not with this type of ignition- side bar makes it where you cannot pick this particular lock
Amigo eate switch se puede desarmar para hacerle la llave?
Do you know the name of the tool. The one to remove the long thick screw like at the center of the steering wheelie. The tool that looks like a wine bottle opener.
Where can i get the clip that holds in the plate mine its bad and i cant find one
You could try at a salvage yard
My lock plate remember is to big what do I do I got the ring out but can’t get it in
I have an 89 GMC that randomly decides it wants to start. Battery’s fine, could this be why?
Wat if u don't have a lock plate removal and ur hands r disabled in a bad way how can I push that in
I broke the piton that you remove right after the hazard switch what is it called so i could replace it
Did you find out what’s that piece called?
@@Hijodelrey420 bump - - - also looking for the answer xD
Same. I dont know where to find one outside of a junkyard
I have problem now after replacing the bearing. I have removed everything followed this video returned everything. When I try to start the engine, there no power. Horn is ok, turn lights, hazards lights, wiper, everything is ok except the ignition switch. What seems to be the issue? Did I miss something? Please help
I'm stuck where the ignition isn't lining up right not sure what to do next I've taken it out 10 times and it's still not lining up
Does anyone know the name of that plastic tab at 5:35
What’s that second special tool called?
What happened to 1aauto 😂
You dont need to take out horn contacts. Broke mine and didnt need to. Save a lot of headache trying to figure out what you broke.
Just wondering about how much does it cost to have the Ignition Lock Cylinder Replaced on a 1989 GMC Truck.
depends on the shop/mechanic labor time. 100 dollars to 200 would be my guess, an individual mechanic may be cheaper.
If you are around the muscle shoals Alabama area my shop charges $50 if u bring the truck and $150 if we come over!
God it’s lame needing a special tool for every little job!
I’ve got to change my ignition on my 85 Buick Leasabre and I’ve never changed an ignition b4 and I’ll be honest, I’m a little nervous. I’d rather change my earl alone with the filter. I’ve also have to change valve cover gaskets. Fun times @Ridgemont High
What the tool your using to push it down called
Thats what iam tryna figure out
Same question
Have you found what it’s called yet?
steering wheel lock plate removal tool
What if my cylinder is stuck in on position?
I have tons of play in my cylinder hopefully that fixes the problem I had ….
Steering column shifter got stuck on drive DIDNT wanna shift into park
I had a mechanic replace a ignition switch for me once. He told me there is a key that will go out shortly afterward. Within 6 months it did. When the key went out my cylinder spun all the way around. That might be your problem. But, I am no mechanic.
I lost my key so can I still do this ? 😩
yes
What if my key ignition is locked?
What happens if I have a lost key. Is it not possible to do this without the key?
Hey did u ever find out the answer to this?
The ignition comes with a new key, I’ve done this twice so far.
Dude. Why are you doing all this to put in a new cylinder? What year is this truck?
why the gloves
This is not easy i figure changing the whole column is easier
Why won’t my key come out
+Derek Hamblin We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Live dangerous leave the battery connected
Thank you.
What is the name or part number of the plastic tab you slid out right before you took the t15 screw and cylinder out? Mine is broke and idn even know what to call it
Its a contact for the horn, if yours is broke it's new column time